Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351183 AUTOMATIC TRANSAXLE SYSTEM C

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P071000  Transmission Fluid Temperature Sensor "A" Circuit Range/Performance  


SYSTEM DESCRIPTION

The ATF temperature sensor converts the automatic transaxle fluid (ATF) temperature into a resistance value for use by the ECM.

The ECM applies a voltage to the ATF temperature sensor through terminal THO1 of the ECM.

The sensor resistance changes with the ATF temperature. As the temperature rises, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance and voltage decrease as the temperature rises.

The ECM calculates the ATF temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071000 Transmission Fluid Temperature Sensor "A" Circuit Range/Performance Either of the following conditions is met (2-trip detection logic):
·

Certain monitor enabling conditions are met and the ATF temperature is below 20°C (68°F).

·

Certain monitor enabling conditions are met and the ATF temperature is 110°C (230°F) or higher.


Transmission wire (ATF temperature sensor) Comes on DTC stored SAE Code:
P0711

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition Certain monitor enabling conditions are met. ○ ○
Malfunction Condition The ATF temperature is below 20°C (68°F). ○ -
The ATF temperature is 110°C (230°F) or higher. - ○
Duration 3 seconds or more 10 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic

HINT:

This DTC is stored when either of the above detection patterns are met.


MONITOR DESCRIPTION

This DTC indicates that there is a problem with output signal from the ATF temperature sensor and that the sensor itself is malfunctioning. The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature sensor circuit or a malfunction of the ATF temperature sensor.

After driving the vehicle for a certain period of time, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after driving the vehicle for a certain period, the ECM interprets this as a malfunction, illuminates the MIL and stores this DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for 2 minutes or more.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Start the engine and perform both of the following:

-

Drive the vehicle 30 km (19 miles) or more over a period of 17 minutes and 15 seconds or more.

-

Wait until 76 minutes and 25 seconds or more have elapsed since the engine was started.


7.

Stop the vehicle.

8.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

9.

Input the DTC: P071000.

10.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

If DTCs P071000 and P261029 are output simultaneously, confirm that the ATF temperature is as specified in "Normal Condition" using the GTS first. When the ATF temperature is as specified in "Normal Condition", perform troubleshooting for DTC P261029.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION



DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Data List.


g.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature No.1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

Approximately 80°C (176°F): After stall speed test

·

Equal to ambient temperature: When engine is cold


If the value is -40°C (-40°F) or 150°C (302°F), the ATF temperature sensor circuit is open or shorted.
Powertrain > Transmission > Data List
Tester Display
A/T Oil Temperature No.1
50003 373 180
HINT:
·

If DTC P071015 is output and the GTS indicates -40°C (-40°F), there is an open in the circuit.

If DTC P071011 is output and the GTS indicates 150°C (302°F) or higher, there is a short in the circuit.

Measure the resistance between terminal THO1 (OIL) and body ground.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or more Short circuit

·

If a circuit related to the ATF temperature sensor becomes open, DTC P071015 is stored immediately (in 0.5 seconds). When DTC P071015 is stored, DTC P071000 cannot be detected.

It is not necessary to inspect the circuit when DTC P071000 is stored.





PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P071000)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only DTC P071000 is output A
DTC P071000 and other DTCs are output B


HINT:

If any DTCs other than DTC P071000 are output, perform troubleshooting for those DTCs first.




A

2.CHECK AUTOMATIC TRANSAXLE FLUID LEVEL

B

2.CHECK AUTOMATIC TRANSAXLE FLUID LEVEL

OK:

Automatic transaxle fluid level is correct.


Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)

NG