Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE FLUID › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351184 AUTOMATIC TRANSAXLE FLUID N

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE FLUID  ADJUSTMENT  


CAUTION / NOTICE / HINT

CAUTION:
C332322

To prevent injury due to contact with an operating V-ribbed belt or cooling fan, keep your hands and clothing away from the V-ribbed belt and cooling fans when working in the engine compartment with the engine running or the engine switch turned on (IG).


PROCEDURE

Hide 1. PRECAUTIONS AND WORK DESCRIPTION

a.

The U761E automatic transaxle assembly does not have an oil filler tube and oil level gauge. When adding automatic transaxle fluid, add automatic transaxle fluid through the refill hole on the rear transaxle cover sub-assembly. The automatic transaxle fluid level can be adjusted by draining excess automatic transaxle fluid (allowing excess automatic transaxle fluid to overflow) through the overflow plug of the automatic transaxle oil pan sub-assembly.

HINT:

"Overflow" indicates the condition under which automatic transaxle fluid comes out of the overflow plug hole.



b.

Before adjusting the automatic transaxle fluid level, add the specified amount of automatic transaxle fluid when the engine is cold and warm up the engine to circulate the automatic transaxle fluid in the automatic transaxle assembly. Ensure that the automatic transaxle fluid temperature is as specified and the engine is idling.

C242969E08
2.844,2.344 2.844,2.229 2.844,2.229 1.948,2.104 false 5.969,2.75 5.969,2.5 5.969,2.5 5.635,2.302 false 1.469,3.219 6.292,3.604 4.823,0.385 12 false 3. ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE 0.042,5.667 4.177,6.01 4.135,0.344 12 false 4. ADJUST AUTOMATIC TRANSAXLE FLUID LEVEL 0.031,0.042 3.792,0.365 3.76,0.323 12 false Automatic Transaxle Fluid Filling Procedure: 0.5,0.406 3.01,0.615 2.51,0.208 12 false 1. PERFORM INITIAL FILLING 3.542,0.177 7.073,0.74 3.531,0.563 12 false 2. ADD SPECIFIED AMOUNT OF AUTOMATIC TRANSAXLE FLUID 0.51,0.771 3.281,1.302 2.771,0.531 10 false Add automatic transaxle fluid to the transaxle oil pan sub-assembly to the specified level. 3.865,0.771 6.99,1.417 3.125,0.646 10 false Add the correct amount of automatic transaxle fluid specified for the operation that was performed. 5.583,2.771 6.51,3.094 0.927,0.323 10 false Overflow Plug 3.563,7.792 5.646,8.729 2.083,0.938 10 false Add automatic transaxle fluid until automatic transaxle fluid comes out of the overflow plug hole. 0.01,2.323 1.833,3.208 1.823,0.885 10 false Add automatic transaxle fluid until automatic transaxle fluid comes out of the overflow plug hole. 0.063,7.781 2.083,8.667 2.021,0.885 10 false Keep the overflow plug open until the automatic transaxle fluid flow slows and only drips come out. 0.104,6.01 2.844,6.635 2.74,0.625 10 false Drain excess automatic transaxle fluid at the specified fluid temperature. 3.49,6 6.885,6.729 3.396,0.729 10 false If no automatic transaxle fluid comes out, add automatic transaxle fluid until automatic transaxle fluid comes out of the overflow plug hole. 0.51,3.667 6.906,4.302 6.396,0.635 10 false Start the engine to circulate the automatic transaxle fluid. Activate fluid temperature detection mode and engine idle speed control mode, and adjust the automatic transaxle fluid temperature to the specified level. 2.125,2.365 3.375,2.729 1.25,0.365 10 false No. 1 Transmission Oil Filler Tube 6.5,1.698 7.115,2.875 0.615,1.177 10 false Specified Amount of Automatic Transaxle Fluid


c.

The U761E automatic transaxle assembly requires Toyota Genuine ATF WS.


d.

The adjustment should be performed according to the procedures and notes.


Hide 2. WORK FLOW

a.

The adjustment should be performed according to the procedure referenced in the work flow below.

C343638E01
0.083,0.083 1.615,0.417 1.531,0.333 10 false WORK FLOW: 3.375,0.333 4.958,0.667 1.583,0.333 10 false START 0.167,0.833 4.906,1.167 4.74,0.333 10 false Step 4. Perform Initial Filling 0.167,1.417 2.917,1.833 2.75,0.417 10 false Operations that require initial filling: 0.167,1.833 3.5,2.583 3.333,0.75 8 false Removal and installation of the front drive shaft assembly 0.167,2.25 3.5,2.917 3.333,0.667 8 false Removal and installation of the torque converter assembly 0.167,2.667 4.083,3.333 3.917,0.667 8 false Removal and installation of the transaxle side cover sub-assembly 0.167,3.083 4.083,4 3.917,0.917 8 false Removal and installation of the transmission valve body assembly 3.917,2.667 6.917,3.583 3,0.917 8 false Replacement of the automatic transaxle assembly 3.917,1.417 7.083,2.083 3.167,0.667 10 false Operations that do not require initial filling: 3.917,1.833 6.833,2.667 2.917,0.833 8 false Repair of an automatic transaxle fluid leak, etc. 3.917,2.25 6.917,3 3,0.75 8 false Disconnection of an oil cooler tube or oil cooler hose 0.167,4.917 4.198,5.656 4.031,0.74 10 false Step 5. Add Specified Amount of Automatic Transaxle Fluid 2.063,5.292 5.615,5.792 3.552,0.5 10 false Add specified amount of automatic transaxle fluid 0.167,5.917 4.917,6.417 4.75,0.5 10 false Step 6, Step 7. Adjust Automatic Transaxle Fluid Temperature 0.583,6.354 6.635,6.875 6.052,0.521 10 false Activate automatic transaxle fluid temperature detection mode and engine idle speed control mode 2.177,6.99 5.208,7.542 3.031,0.552 10 false Idling (Warm up the automatic transaxle fluid) 1.479,7.75 5.073,8.188 3.594,0.438 10 false Automatic transaxle fluid level adjustment temperature 5.25,7.24 6.948,8.177 1.698,0.938 10 false Above automatic transaxle fluid level adjustment temperature

C338930E03
0.167,0.917 3.813,1.292 3.646,0.375 10 false Step 8. Adjust Automatic Transaxle Fluid Level 2.396,1.427 5.313,1.792 2.917,0.365 10 false Drain excess automatic transaxle fluid 3.313,2.208 3.958,2.604 0.646,0.396 10 false Overflow 2.115,3.198 5.104,3.563 2.99,0.365 10 false Check the amount of automatic transaxle fluid 5.385,3.25 6.969,3.823 1.583,0.573 10 false Add automatic transaxle fluid 5.208,2.031 7,2.594 1.792,0.563 10 false No automatic transaxle fluid comes out 2.99,4.458 4.646,4.833 1.656,0.375 10 false Finish up operation 0.146,4.323 1.25,4.833 1.104,0.51 10 false Step 9. Rebuild Work 3.417,5.396 4.302,5.75 0.885,0.354 10 false END


Hide 3. PREPARATION WORK

a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear and side to side of the vehicle is within +/- 1°).



b.

Remove the front fender apron seal LH.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


Hide 4. PERFORM INITIAL FILLING

NOTICE:

If the automatic transaxle assembly is hot (automatic transaxle fluid temperature is high), wait until the automatic transaxle fluid temperature becomes the same as the ambient temperature before starting the following procedure. (Recommended automatic transaxle fluid temperature: around 20°C (68°F))


a.
C378107

Remove the refill plug and gasket from the rear transaxle cover sub-assembly.

NOTICE:

After performing either of the following operations, it is not necessary to perform the initial filling procedure. Proceed to the "Add Specified Amount of Automatic Transaxle Fluid" procedure.


Operations that do not require initial filling
·

Disconnection of a transmission oil cooler or oil cooler hose

·

Repair of an automatic transaxle fluid leak due to a loose case plug, or a faulty plug gasket or O-ring

·

Replacement of the automatic transaxle assembly




b.
C378108

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly.

NOTICE:
·

If automatic transaxle fluid comes out after removing the overflow plug, wait until the automatic transaxle fluid flow slows and only drips come out.

·

If automatic transaxle fluid comes out, it is not necessary to perform the initial filling procedure. After checking the tightening torque of the No. 1 transmission oil filler tube, temporarily install the overflow plug.




c.
C378109C01
0.719,1.156 0.844,1.156 false 0.865,1.042 1.177,1.24 0.313,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, check that the No. 1 transmission oil filler tube is tightened to the specified torque.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)

NOTICE:

If the No. 1 transmission oil filler tube is not tightened to the specified torque, the amount of automatic transaxle fluid cannot be precisely adjusted.


HINT:

To check the torque of the No. 1 transmission oil filler tube, insert the 6 mm hexagon socket wrench into the overflow plug hole.



d.

Perform initial filling.

i.
C378117

Fill the automatic transaxle assembly through the refill hole until automatic transaxle fluid begins to come out of the overflow plug hole.

NOTICE:

Use Toyota Genuine ATF WS.




e.
C378118

Wait until the automatic transaxle fluid flow slows and only drips come out.


f.
C378108

Using a 6 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the automatic transaxle oil pan sub-assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.



g.
C378107

Temporarily install the gasket and refill plug to the rear transaxle cover sub-assembly.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.



Hide 5.ADD SPECIFIED AMOUNT OF AUTOMATIC TRANSAXLE FLUID

a.
C378107

Remove the refill plug and gasket from the rear transaxle cover sub-assembly.


b.
C378111

Fill the automatic transaxle assembly with the correct amount of automatic transaxle fluid as listed in the table below.

NOTICE:

Use Toyota Genuine ATF WS.


HINT:

The refill amount differs depending on the operation that was performed.


Reference Capacity:
Performed Repair Fill Amount
Automatic transaxle assembly replacement (with a new torque converter assembly) 5.1 liters (5.4 US qts, 4.5 Imp. qts)
Automatic transaxle assembly replacement (when reusing the torque converter assembly) 3.5 liters (3.7 US qts, 3.1 Imp. qts)
Removal and installation of the automatic transaxle oil pan sub-assembly 3.2 liters (3.4 US qts, 2.8 Imp. qts)
Removal and installation of a front drive shaft assembly 3.2 liters (3.4 US qts, 2.8 Imp. qts)
Removal and installation of the transmission valve body assembly 3.7 liters (3.9 US qts, 3.3 Imp. qts)
Removal and installation of the torque converter assembly 3.4 liters (3.6 US qts, 3.0 Imp. qts)
Repair of an automatic transaxle fluid leak due to a loose case plug, or a faulty plug gasket or O-ring 0.5 liters (0.5 US qts, 0.4 Imp. qts)



c.
C378107

Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.



d.

Lower the vehicle.


Hide 6.ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Using the GTS)

HINT:

The actual automatic transaxle fluid temperature can be checked on the Data List using the GTS.


a.

Connect the GTS to the DLC3 with the engine switch off.


b.

Turn the engine switch on (IG) and turn the GTS on.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system are off.



c.

Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.

Powertrain > Transmission > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
A/T Oil Temperature No.1
50004 373 22 180

d.

According to the display on the GTS, perform the Data List "A/T Oil Temperature No.1".


e.

According to the display on the GTS, perform the Active Test Activate the TC Terminal and set it to "ON".


f.

Check the automatic transaxle fluid temperature.

NOTICE:
·

If the automatic transaxle fluid temperature is below 45°C (113°F), proceed to the next step. Recommended automatic transaxle fluid temperature: 35°C (95°F) or less

·

If the automatic transaxle fluid temperature is 45°C (113°F) or more, turn the engine switch off and wait until the automatic transaxle fluid temperature drops below 45°C (113°F).




g.

Depress and hold the brake pedal.


h.

Start the engine.


i.

Slowly move the shift lever from P to D, then back to P.

HINT:
·

Slowly move the shift lever to circulate the automatic transaxle fluid through each part of the automatic transaxle assembly.

·

Keep the shift lever in each position for approximately 3 seconds.




j.
C370813

While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter automatic transaxle fluid temperature detection mode.



k.

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When automatic transaxle fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the first step (perform the Active Test Activate the TC Terminal and set it to "ON") and perform the procedure again.




l.

Move the shift lever to P.


m.

Release the brake pedal.


n.

According to the display on the GTS, perform the Active Test Activate the TC Terminal and set it to "OFF".

NOTICE:

Make sure that the Active Test is changed to "OFF". If it is not, the automatic transaxle fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Changing the Active Test to "OFF" activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the automatic transaxle fluid temperature reaches the specified temperature and the engine speed is maintained.

·

Even after the Active Test is changed to "OFF", automatic transaxle fluid temperature detection mode will be active until the engine switch is turned off.




o.

Adjust the automatic transaxle fluid temperature to the automatic transaxle fluid level adjustment temperature.

Automatic Transaxle Fluid Temperature
Below Automatic Transaxle Fluid Level Adjustment Temperature Automatic Transaxle Fluid Level Adjustment Temperature Above Automatic Transaxle Fluid Level Adjustment Temperature
35°C or less
(95°F or less)
35 to 45°C
(95 to 113°F)
45°C or more
(113°F or more)

NOTICE:
·

If the automatic transaxle fluid temperature is within the automatic transaxle fluid level adjustment temperature range, immediately proceed to the "Adjust Automatic Transaxle Fluid Level" procedure.

·

If the automatic transaxle fluid temperature is 45°C (113°F) or more, stop the engine and wait until the automatic transaxle fluid temperature drops to 40°C (104°F) or less. Then perform the "Adjust Automatic Transaxle Fluid Temperature" procedure again from the beginning.



HINT:

In automatic transaxle fluid temperature detection mode, the D shift indicator comes on, turns off or blinks depending on the automatic transaxle fluid temperature.

D Shift Indicator
Below Automatic Transaxle Fluid Level Adjustment Temperature
(35°C or less)
(95°F or less)
Automatic Transaxle Fluid Level Adjustment Temperature
(35 to 45°C)
(95 to 113°F)
Above Automatic Transaxle Fluid Level Adjustment Temperature
(45°C or more)
(113°F or more)
OFF ON Blinks



Hide 7.ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Not Using the GTS)

a.
C166029C88
1.594,0.906 1.823,0.458 1.823,0.458 2.021,0.458 true 2.104,1.833 1.969,1.833 1.969,1.833 1.792,1.479 true 2.156,1.75 2.396,1.927 0.24,0.177 10 false TC 2.063,0.365 2.365,0.542 0.302,0.177 10 false CG 0.167,0.115 0.385,0.292 0.219,0.177 10 false *1
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the engine switch off.

SST
09843-18040  


b.

Depress and hold the brake pedal.


c.

Start the engine.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system are off.



d.

Slowly move the shift lever from P to D, then back to P.

HINT:
·

Slowly move the shift lever to circulate the automatic transaxle fluid through each part of the automatic transaxle assembly.

·

Keep the shift lever in each position for approximately 3 seconds.




e.
C370813

While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter automatic transaxle fluid temperature detection mode.



f.

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When automatic transaxle fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the first step (connect terminals 13 (TC) and 4 (CG) of the DLC3) and perform the procedure again.




g.

Move the shift lever to P.


h.

Release the brake pedal.


i.

Remove SST from terminals 13 (TC) and 4 (CG).

SST
09843-18040  

NOTICE:

Make sure that the terminals are not connected. If the terminals are connected, the automatic transaxle fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting the terminals activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the automatic transaxle fluid temperature reaches the specified temperature and the engine speed is maintained.

·

Even after the terminals are disconnected, automatic transaxle fluid temperature detection mode is active until the engine switch is turned off.




j.

Allow the engine to idle until the D shift indicator comes on again.

D Shift Indicator
Below Automatic Transaxle Fluid Level Adjustment Temperature
(35°C or less)
(95°F or less)
Automatic Transaxle Fluid Level Adjustment Temperature
(35 to 45°C)
(95 to 113°F)
Above Automatic Transaxle Fluid Level Adjustment Temperature
(45°C or more)
(113°F or more)
OFF ON Blinks

NOTICE:
·

If the D shift indicator is on, immediately proceed to the "Adjust Automatic Transaxle Fluid Level" procedure.

·

If the D shift indicator blinks, stop the engine and wait until the automatic transaxle fluid temperature drops to 35°C (95°F) or less (the indicator turns off). Then perform the "Adjust Automatic Transaxle Fluid Temperature" procedure again from the beginning.



HINT:
·

In automatic transaxle fluid temperature detection mode, the D shift indicator comes on, turns off, or blinks depending on the automatic transaxle fluid temperature.

·

The automatic transaxle fluid filling procedure should be performed when the D shift indicator is on (the automatic transaxle fluid temperature is within the automatic transaxle fluid level adjustment temperature range).




Hide 8.ADJUST AUTOMATIC TRANSAXLE FLUID LEVEL

CAUTION:

Use caution while the engine is idling and the radiator fans are operating.


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear and side to side of the vehicle is within +/- 1°).



b.
C378108

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly.

CAUTION:

Be careful as the automatic transaxle fluid coming out of the overflow plug hole is hot.



c.

Check the amount of automatic transaxle fluid that comes out of the overflow plug hole.

·

If the amount of automatic transaxle fluid that comes out of the overflow plug hole is large, proceed to step [#1].

·

If no automatic transaxle fluid comes out of the overflow plug hole, proceed to step [#2].


NOTICE:

If only a small amount of automatic transaxle fluid (approximately 1 cc) comes out of the overflow plug hole, then only automatic transaxle fluid remaining in the No. 1 transmission oil filler tube has come out. This condition is not considered as overflow, so it is necessary to add automatic transaxle fluid.



d.

If the amount of automatic transaxle fluid that comes out of the overflow plug hole is large. [#1]

i.
C378118

Wait until the automatic transaxle fluid flow slows and only drips come out.

HINT:

The automatic transaxle fluid flow will not stop completely because the automatic transaxle fluid continues to expand as its temperature increases.




e.

If no automatic transaxle fluid comes out of the overflow plug hole. [#2]

i.
C378107

Remove the refill plug and gasket from the rear transaxle cover sub-assembly.


ii.
C378117

Add automatic transaxle fluid through the refill hole until automatic transaxle fluid comes out of the overflow plug hole.

NOTICE:

Use Toyota Genuine ATF WS.



iii.
C378118

Wait until the automatic transaxle fluid flow slows and only drips come out.



f.
C378108

Using a 6 mm hexagon socket wrench, install the overflow plug and a new gasket to the automatic transaxle oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


g.
C378394C01
1.25,0.406 1.25,0.146 1.25,0.146 1.385,0.146 true 0.594,1.01 0.823,1.208 0.229,0.198 10 true *a 1.438,0.021 1.771,0.208 0.333,0.188 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the refill plug and a new gasket to the rear transaxle cover sub-assembly.

SST
09922-10240  

Torque:
Specified tightening torque : 49 N*m (500 kgf*cm, 36 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 40 mm (1.57 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)):

42.4 N*m (432 kgf*cm, 31 ft.*lbf)




h.

Lower the vehicle.


i.

Turn the engine switch off.

HINT:

Turning the engine switch off ends automatic transaxle fluid temperature detection mode.



j.

Disconnect the GTS from the DLC3 (when using the GTS).


Hide 9. REBUILD WORK

a.

Lift the vehicle.


b.

Clean each part.


c.

Check for automatic transaxle fluid leaks.


d.

e.

Lower the vehicle.