Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351183 AUTOMATIC TRANSAXLE SYSTEM C

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P275613  Torque Converter Clutch Pressure Control Solenoid Control Circuit Open  


DESCRIPTION

The ECM uses signals from the throttle position sensor, air-flow meter, input speed sensor NT, output speed sensor NC and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.

C315080C01
1.792,1.417 2.125,0.417 2.125,0.417 2.542,0.417 true 1.219,1.646 0.969,2.146 0.969,2.146 0.635,2.146 true 2.521,1.688 2.771,2.188 2.771,2.188 3.104,2.188 true 2.583,0.333 2.896,0.49 0.313,0.156 10 false *a 0.458,2.063 0.771,2.219 0.313,0.156 10 false *b 3.146,2.104 3.458,2.26 0.313,0.156 10 false *c 4.802,0.625 5.115,0.781 0.313,0.156 10 false *d 6.135,2.031 6.448,2.188 0.313,0.156 10 false *e
*a Spool Valve *b Sleeve
*c Solenoid Coil *d Hydraulic Pressure
*e Current - -


The ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect mechanical malfunctions of the solenoid (SLU) valve, transmission valve body assembly and torque converter clutch.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P275613 Torque Converter Clutch Pressure Control Solenoid Control Circuit Open While the vehicle is being driven, an open or short is detected in the solenoid (SLU) valve circuit for 1 second (1-trip detection logic).
·

Wiring harness connector

·

Open or short in solenoid (SLU) valve circuit

·

Solenoid (SLU) valve

·

Transmission wire

·

ECM


Comes on DTC stored SAE Code:
P2759

MONITOR DESCRIPTION

When an open or short in the solenoid (SLU) valve circuit is detected, the ECM determines there is a malfunction, illuminates the MIL and stores a DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for 2 minutes or more.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Start the engine.

7.

Perform the Lock-up Function inspection in Road Test.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P275613.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C314405E71
1.188,3.01 5.469,3.208 4.281,0.198 10 false Transmission Wire 3.042,3 4.063,3.396 1.021,0.396 10 false Wiring Harness Connector 5.583,3 6.042,3.198 0.458,0.198 10 false C58 5.594,3.167 6.052,3.365 0.458,0.198 10 false ECM 1.542,1.552 2.479,1.99 0.938,0.438 10 false Solenoid (SLU) Valve 2.333,1.021 2.948,1.219 0.615,0.198 10 false SLU+ 3.083,1.021 3.698,1.219 0.615,0.198 10 false SLU+ 3.594,1.021 4.208,1.219 0.615,0.198 10 false SLU+ 5.042,1.031 5.656,1.229 0.615,0.198 10 false SLU+ 5.052,2.021 5.667,2.219 0.615,0.198 10 false SLU- 3.625,2.021 4.24,2.219 0.615,0.198 10 false SLU- 3.083,2.021 3.698,2.219 0.615,0.198 10 false SLU- 2.365,2.021 2.979,2.219 0.615,0.198 10 false SLU- 2.823,1.125 2.979,1.323 0.156,0.198 10 false A 2.833,2.125 2.99,2.323 0.156,0.198 10 false A 4.021,1.104 4.333,1.302 0.313,0.198 10 false C54 4.021,2.104 4.333,2.302 0.313,0.198 10 false C54 4.906,1.031 5.219,1.229 0.313,0.198 10 false 3 4.906,2.021 5.219,2.219 0.313,0.198 10 false 2 4.115,1.917 4.427,2.115 0.313,0.198 10 false 5 4.063,0.927 4.375,1.125 0.313,0.198 10 false 14 2.792,0.927 3.104,1.125 0.313,0.198 10 false 11 2.844,1.938 3.156,2.135 0.313,0.198 10 false 5 5.625,0.76 6.156,1.01 0.531,0.25 10 false 12 V 1.26,1.313 1.417,1.51 0.156,0.198 10 false 2 1.25,1.948 1.406,2.146 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SOLENOID (SLU) VALVE CIRCUIT)
a.

Disconnect the C58 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-3 (SLU+) - C58-2 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C58-3 (SLU+) - Body ground and other terminals Always 10 kΩ or higher
C58-2 (SLU-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
a.

Disconnect the C54 wiring harness connector connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-3 (SLU+) - C54-14 (SLU+) Always Below 1 Ω
C58-2 (SLU-) - C54-5 (SLU-) Always Below 1 Ω
C58-3 (SLU+) or C54-14 (SLU+) - Body ground and other terminals Always 10 kΩ or higher
C58-2 (SLU-) or C54-5 (SLU-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (SOLENOID (SLU) VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION WIRE (SOLENOID (SLU) VALVE)
a.
C370674C06
0.417,1 0.833,1.25 0.417,0.25 1.75,1.896 2,1.313 true 2.365,1.885 2.042,1.146 true 0.573,1.031 0.729,1.229 0.156,0.198 10 false A 1.344,1.823 1.958,2.021 0.615,0.198 10 false SLU+ 2.417,1.823 3.031,2.021 0.615,0.198 10 false SLU- 0.333,0.344 0.646,0.5 0.313,0.156 10 false *a
*a Component without harness connected
(Transmission Wire)


Remove the wiring harness connector.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-11 (SLU+) - A-5 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
A-11 (SLU+) - Body ground and other terminals Always 10 kΩ or higher
A-5 (SLU-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT SOLENOID (SLU) VALVE
4.INSPECT SOLENOID (SLU) VALVE
a.
C201747C02
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 0.49,0.521 0.667,0.719 0.177,0.198 10 1 2.531,0.5 2.708,0.698 0.177,0.198 10 2 1.177,4.198 1.385,4.406 0.208,0.208 10 (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 (+) 0.51,2.771 0.688,2.969 0.177,0.198 10 1 2.521,2.76 2.698,2.958 0.177,0.198 10 2 0.135,0.135 0.354,0.344 0.219,0.208 10 *1
*1 Solenoid (SLU) Valve


Remove the solenoid (SLU) valve.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG