Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351457 ENGINE ASSEMBLY A

6AR-FSE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 12372A 1.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>INSTALLATION

Hide 12304 2.INSTALL ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting bracket sub-assembly LH is necessary.


a.
A413650N01
2.208,0.458 2.365,0.656 0.156,0.198 10 true A 2.292,1.802 2.448,2 0.156,0.198 10 true B 0.625,0.75 0.781,0.948 0.156,0.198 10 true C 1.604,0.177 1.76,0.375 0.156,0.198 10 true D

Temporarily tighten the bolt (A), and then fully tighten the 4 bolts in the order of (B), (C), (D) and (A).

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Make sure that there is no gap between the engine mounting bracket sub-assembly LH and vehicle body before tightening the bolts.



Hide 12341 3.INSTALL ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A413649N01
0.708,1.677 0.865,1.875 0.156,0.198 10 true A 2.51,1.104 2.667,1.302 0.156,0.198 10 true B

Install the engine mounting spacer to the vehicle body with the 2 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).



Hide 12305 4.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A413648N01
0.729,1.177 0.885,1.375 0.156,0.198 10 true A 2.49,1.688 2.646,1.885 0.156,0.198 10 true B 2.5,0.375 2.656,0.573 0.156,0.198 10 true C

Install the engine mounting insulator sub-assembly RH with the 2 bolts and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts and nut in the order of (B), (A) and (C).



b.

Engage the clamp.


c.

Connect the No. 1 bond cable to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


d.

Connect the bracket to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.
A413646C01
0.813,1.229 1.021,1.427 0.208,0.198 10 true *a 2.458,0.406 2.667,0.604 0.208,0.198 10 true *b
*a Bolt
*b Nut


Install the radiator reserve tank assembly with the bolt and nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Temporarily tighten the bolt, nut and then fully tighten the bolt and nut in the order of bolt and nut.



f.

Engage the clamp.


g.

Connect the No. 6 water by-pass hose.


Hide 6.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 82121 7.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 32101 8.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 11.INSTALL NO. 1 TRANSMISSION OIL COOLER HOSE ASSEMBLY

Hide 33493A 12.INSTALL TRANSMISSION OIL COOLER

Hide 13.CONNECT NO. 1 TRANSMISSION OIL COOLER HOSE ASSEMBLY

Hide 16281N 14.CONNECT NO. 4 WATER BY-PASS HOSE

Hide 28100 15.INSTALL STARTER ASSEMBLY

Hide 12371A 16.INSTALL REAR ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator to the rear engine mounting bracket with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 12361A 17.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the front engine mounting insulator to the front engine mounting bracket with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 51100G 18.INSTALL FRONT FRAME ASSEMBLY

a.

Install the front frame assembly with the 7 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 20.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:

Perform inspection after repair after replacing the engine assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly with transaxle.




b.

Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.


c.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




d.
A413641C02
0.792,0.302 0.948,0.5 0.156,0.198 10 true B 2.51,0.302 2.667,0.5 0.156,0.198 10 true B 1.24,2.031 1.396,2.229 0.156,0.198 10 true A 1.229,2.281 1.385,2.479 0.156,0.198 10 true A 1.115,2.542 1.271,2.74 0.156,0.198 10 true C 2.146,2.542 2.302,2.74 0.156,0.198 10 true C 2.052,2.042 2.208,2.24 0.156,0.198 10 true A 2.052,2.292 2.208,2.49 0.156,0.198 10 true A 0.646,3.823 0.802,4.021 0.156,0.198 10 true E 0.708,4.448 0.865,4.646 0.156,0.198 10 true D 2.573,4.469 2.729,4.667 0.156,0.198 10 true D 2.615,3.854 2.771,4.052 0.156,0.198 10 true E
V100135

Bolt
V100136

Nut


Install the front bumper extension sub-assembly RH and front bumper extension sub-assembly LH to the front frame assembly and vehicle body with the 8 bolts.

Torque:
Bolt (A) : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
Bolt (B) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (C) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)


e.

Install the front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH to the front frame assembly and vehicle body with the 4 bolts and 2 nuts.

Torque:
Bolt (D) : 17.5 N*m (178 kgf*cm, 13 ft.*lbf)
Bolt (E) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Nut : 17.5 N*m (178 kgf*cm, 13 ft.*lbf)


f.

Install the engine mounting insulator LH to the engine mounting bracket sub-assembly LH with the bolt and nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

While holding the bolt in place, tighten the nut.



g.

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 42 N*m (428 kgf*cm, 31 ft.*lbf)


h.

Engage the clamp.


Hide 32101A 21.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 11361J 22.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the cylinder block sub-assembly.


Hide 17410 24.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 45220 25.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 26.CONNECT WIRE HARNESS

a.

Connect the wire harness to the vehicle body with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Engage the claw to connect the wire harness to the engine room relay block and junction block assembly.


c.

Connect the 4 connectors.


d.

Install the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Install the relay block cover.


f.

Connect the wire harness with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 27.CONNECT WATER HOSE

a.

Engage the 2 clamps.


b.

Connect the 2 water hoses and slide the 2 clips to secure them.


c.

Engage the clamp.


d.

Connect the water hose and slide the clip to secure it.


Hide 88704 28.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88711 29.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 16572D 30.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.


Hide 16571C 31.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.


Hide 44773F 32.CONNECT UNION TO CHECK VALVE HOSE

Hide 23826 33.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the No. 1 vacuum switching valve assembly and slide the clip to secure it.


Hide 23901 34.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the 2 No. 1 fuel hoses.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


c.

Engage the 2 claws to install the No. 2 fuel pipe clamp.


Hide 33820B 35.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


b.

Connect the transmission control cable assembly to the transmission control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.



Hide 74404A 36.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the battery clamp sub-assembly with the 3 bolts.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


b.

Engage the 5 clamps to the battery clamp sub-assembly.


Hide 38.CONNECT WIRE HARNESS

a.

Connect the wire harness to the positive (+) battery terminal with the nut.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


Hide 40.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A413651C01
1.469,4.365 0.854,4.344 0.854,4.344 1.208,4.24 true 2.281,4.146 2.531,4.146 true 0.594,4.25 0.813,4.438 0.219,0.188 10 true *a 2.531,4.052 2.75,4.24 0.219,0.188 10 true *a
*a Air Cleaner Support


Connect the air cleaner assembly with air cleaner hose to the throttle body with motor assembly and tighten the hose clamp.


b.

Insert the 3 pins of the air cleaner assembly into the 3 air cleaner supports as shown in the illustration.

NOTICE:
·

Insert the 3 pins of the air cleaner assembly into the 3 air cleaner supports at the same time.

·

Check that the pins are securely inserted into air cleaner supports.




c.

Engage the 2 clamps.


d.

Connect the ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.


e.

Engage the 2 clamps.


f.

Engage the clamp.


g.

Engage the 3 wire harness clamps.


h.

Connect the mass air flow meter sub-assembly connector.


Hide 17750A 41.INSTALL INLET AIR CLEANER ASSEMBLY

a.
A413619N01
0.563,1.615 0.719,1.813 0.156,0.198 10 true 1 1.385,1.604 1.542,1.802 0.156,0.198 10 true 2

Install the inlet air cleaner assembly with the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12601B 42.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

Engage the 3 clips to install the No. 1 engine cover sub-assembly.


Hide 43.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45.ADD ENGINE COOLANT

Hide 46.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 50.INSPECT FOR ENGINE OIL LEAK

Hide 56.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK

Hide 52618 57.INSTALL FRONT LOWER BUMPER ABSORBER

a.

Engage the 2 claws to install the front lower bumper absorber.


b.

Install the 4 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 52119A 58.INSTALL FRONT BUMPER COVER

Hide 53737B 59.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 2 screws and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53736 60.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal RH with the 2 screws and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51441 61.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the bolt, 6 screws and 2 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53852K 62.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

a.

Install the front wheel opening extension pad LH with the 3 screws.


Hide 53851M 63.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

a.

Install the front wheel opening extension pad RH with the 3 screws.


Hide 64.INSTALL FRONT WHEELS

Hide 65. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 66.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT