Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › VALVE BODY ASSEMBLY › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351187 VALVE BODY ASSEMBLY A

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during transmission valve body assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

*3: The vehicle height changes because of suspension or tire replacement.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly Perform the following procedures in the order shown:
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for U761E Initialization
(Click here)for U761E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Engine start


See Service Bulletin for the registration method.
Suspension, tires*3 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
·

Replacement of transmission valve body assembly

·

Replacement of solenoid (SL3 and/or SL4) valve


Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for U761E Initialization
(Click here)for U761E Registration
Replacement of solenoid (SL1 and/or SL2) valve Perform road test to allow ECM to learn

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Transmission Jack


The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.



PROCEDURE

Hide 35106D 3.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C385275

Remove the 19 bolts and automatic transaxle oil pan sub-assembly from the transaxle case sub-assembly.

NOTICE:

Some fluid will remain in the automatic transaxle oil pan sub-assembly. Remove all of the bolts and carefully remove the automatic transaxle oil pan sub-assembly.



Hide 35168A 4.REMOVE AUTOMATIC TRANSAXLE OIL PAN GASKET

a.

Remove the automatic transaxle oil pan gasket from the automatic transaxle oil pan sub-assembly.


Hide 35394 5.REMOVE TRANSMISSION OIL CLEANER MAGNET

a.
C317150C01
1.948,0.531 1.948,0.167 1.948,0.167 0.302,0.167 false 0.885,1.052 0.885,0.177 false 1.594,0.656 1.594,0.167 false 1.115,1.49 1.115,0.177 false 0.104,0.104 0.458,0.385 0.354,0.281 10 false *1
*1 Transmission Oil Cleaner Magnet


Remove the 4 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


Hide 35394 6.INSPECT TRANSMISSION OIL CLEANER MAGNET

Hide 35330 7.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.
C379911

Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.


b.
C317151C01
0.719,0.406 1.26,0.406 false 0.531,0.333 0.896,0.677 0.365,0.344 10 false *1
*1 O-ring


Remove the O-ring from the valve body oil strainer assembly.


Hide 35410 8.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C379912

Remove the 11 bolts and transmission valve body assembly from the transaxle case sub-assembly.

NOTICE:
·

When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.

·

As the manual valve is not secured to the transmission valve body assembly, make sure it does not fall out when removing the transmission valve body assembly.




Hide 35145C 9.REMOVE TRANSAXLE CASE GASKET

a.
C201316

Remove the 2 transaxle case gaskets from the transaxle case sub-assembly.


Hide 35418 10.REMOVE MANUAL VALVE

a.
C201705

Remove the manual valve from the transmission valve body assembly.