Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL PUMP › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351197 OIL PUMP A

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  REASSEMBLY  


PROCEDURE

Hide 35301A 1.INSTALL FRONT OIL PUMP OIL SEAL

a.
C188149C01
1.313,2.052 1.042,2.052 false 2.438,1.333 2.333,1.333 2.333,1.333 1.781,0.906 false 2.49,1.24 2.99,1.531 0.5,0.292 10 false SST 0.719,1.958 1.01,2.115 0.292,0.156 10 false SST 0.625,2.333 1,2.646 0.375,0.313 10 false *a
*a Depth


Using SST and a hammer, install a new front oil pump oil seal to the front oil pump body sub-assembly.

SST
09350-32014  (09351-32140)

Standard Depth:

-0.25 to 0.25 mm (-0.00984 to 0.00984 in.)


NOTICE:

The front oil pump oil seal end should be level with the outer edge of the front oil pump body sub-assembly.



b.

Coat the lip of the front oil pump oil seal with MP grease.


Hide 2.INSTALL FRONT OIL PUMP BODY O-RING

a.
C138278

Coat a new front oil pump body O-ring with Toyota Genuine ATF WS and install it to the front oil pump body sub-assembly.

NOTICE:

Make sure that the front oil pump body O-ring is installed correctly with the identification line facing outward and check that it is not twisted, protruding or damaged.



Hide 35322 3.INSTALL FRONT OIL PUMP DRIVEN GEAR

a.
C316894

Coat the front oil pump driven gear with Toyota Genuine ATF WS and install it to the front oil pump body sub-assembly with the marked side facing upward.


Hide 35321 4.INSTALL FRONT OIL PUMP DRIVE GEAR

a.
C316893

Coat the front oil pump drive gear with Toyota Genuine ATF WS and install it to the front oil pump body sub-assembly with the marked side facing upward.


Hide 35370 5.INSTALL STATOR SHAFT ASSEMBLY

a.
C138275N04
1.45,2.46 1.6,2.625 0.15,0.165 10 B 0.766,1.177 0.916,1.342 0.15,0.165 10 A 1.005,0.553 1.155,0.718 0.15,0.165 10 A 1.659,0.194 1.809,0.36 0.15,0.165 10 A 2.295,0.507 2.445,0.672 0.15,0.165 10 A 2.579,0.975 2.73,1.14 0.15,0.165 10 A 2.554,1.613 2.704,1.778 0.15,0.165 10 A 2.183,2.087 2.333,2.252 0.15,0.165 10 A 1.707,2.207 1.858,2.372 0.15,0.165 10 A 1.004,1.868 1.143,2.033 0.14,0.165 10 A 2.226,2.681 2.376,2.846 0.15,0.165 10 B 2.438,3.298 2.588,3.463 0.15,0.165 10 B 2.377,4.008 2.527,4.173 0.15,0.165 10 B 0.875,3.831 1.025,3.996 0.15,0.165 10 B 0.887,3.041 1.038,3.206 0.15,0.165 10 B 1.339,4.248 1.489,4.413 0.15,0.165 10 B

Align each knock pin of the stator shaft assembly with the holes in the front oil pump and gear body sub-assembly and install the stator shaft assembly to the front oil pump and gear body sub-assembly.

NOTICE:

Do not drop the front oil pump drive gear and front oil pump driven gear.



b.

Using a T30 "TORX" socket wrench, install the 16 bolts.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)

Bolt Length:
Bolt (A):

14 mm (0.551 in.)

Bolt (B):

26 mm (1.02 in.)



Hide 35035 6.INSPECT FRONT OIL PUMP ASSEMBLY