Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351198 DIFFERENTIAL CASE A

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41039A 1.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C288461C02
0.771,0.688 0.635,0.302 0.635,0.302 0.552,0.302 false 1.719,0.74 1.583,0.333 1.583,0.333 1.5,0.333 false 2.5,0.708 2.365,0.323 2.365,0.323 2.281,0.323 false 0.406,0.229 0.719,0.385 0.313,0.156 10 false *1 1.323,0.25 1.635,0.406 0.313,0.156 10 false *2 2.104,0.25 2.417,0.406 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer
V100135

ATF


Coat the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs with Toyota Genuine ATF WS.


b.
C317734C01
2.198,0.177 2.406,0.177 false 2.281,0.333 2.448,0.333 false 2.188,0.719 2.354,0.719 false 2.188,1.323 2.354,1.323 false 2.292,1.719 2.458,1.719 false 2.198,1.854 2.417,1.854 false 2.021,0.635 2.333,0.792 0.313,0.156 10 false *1 2.125,0.25 2.438,0.406 0.313,0.156 10 false *2 2.042,0.104 2.354,0.26 0.313,0.156 10 false *3 2.042,1.24 2.354,1.396 0.313,0.156 10 false *1 2.146,1.625 2.458,1.781 0.313,0.156 10 false *2 2.042,1.771 2.354,1.927 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Install the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs to the front differential case.

NOTICE:
·

Do not drop the front differential side gears, front No. 1 differential side gear thrust washers or conical springs.

·

Make sure that the conical springs are installed with the correct orientation.




c.

Install SST as shown in the illustration and tighten it.

C317732C01
4.625,0.26 5.146,0.26 false 5.104,1.667 4.885,1.521 4.885,1.521 5.094,1.396 false 4.375,1.521 4.896,1.521 false 3.177,0.229 3.51,0.542 0.333,0.313 10 false *a 1.042,2.406 1.417,2.677 0.375,0.271 10 false *b 4.313,0.177 4.802,0.615 0.49,0.438 10 false SST 4.063,1.448 4.552,1.885 0.49,0.438 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

NOTICE:

Do not overtighten SST as doing so will damage the front differential side gears, conical springs, front No. 1 differential side gear thrust washers and front differential case.


HINT:
·

Tighten SST to create the necessary clearance to install the front differential pinions.

·

When installing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




d.
C287727C02
0,0 0,0 false
V100135

ATF


Coat the 2 front differential pinions and 2 front differential pinion thrust washers with Toyota Genuine ATF WS.


e.
C317743C01
2.583,2.354 2.583,2.823 2.583,2.823 2.75,2.823 false 1.969,0.719 2.302,1.031 0.333,0.313 10 false *a 2.802,2.75 3.177,3.042 0.375,0.292 10 false SST
*a Turn


Using SST as shown in the illustration and rotate the front differential side gear and install the 2 front differential pinions to 2 front differential pinion thrust washers.

SST
09528-52010  (09528-05030)

CAUTION:

Be careful not to pinch your fingers between the front differential pinion and front differential case.


NOTICE:

Do not drop the front differential pinions or front differential pinion thrust washers.



Hide 2.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41342F 3.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C317744C01
2.813,1.417 2.781,1.5 false
V100135

ATF


Coat the front No. 1 differential pinion shaft with Toyota Genuine ATF WS.


b.

Install the front No. 1 differential pinion shaft to the front differential case so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case.


Hide 41342A 5.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C317745

Using a 5 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the front differential case.


b.
C317746

Using a chisel and a hammer, stake the front differential case.


Hide 41221 6.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the front differential ring gear to more than 110°C (230°F).



b.

Clean the contact surface of the front differential case.


c.
C317727C01
1.167,1.469 0.427,0.99 0.427,0.99 1.229,1.406 true 0.24,0.833 0.677,1.25 0.438,0.417 10 false *a
*a Matchmark


Align the matchmarks, and install the front differential ring gear to the front differential case quickly.


d.
C317728

Install the 12 bolts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:
·

Tighten the bolts after the front differential ring gear has cooled down sufficiently.

·

Tighten the bolts evenly in a diagonal pattern using several steps.