Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (except 2AR-FE) › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0326622 CRUISE CONTROL SYSTEM(except 2AR-FE) J

CRUISE CONTROL  CRUISE CONTROL SYSTEM(except 2AR-FE)  Steering Pad Switch Circuit  


DESCRIPTION

·

The steering pad switch assembly outputs the on/off signal and various control signals to the ECM.

·

The ECM performs cruise control according to the signals received from the steering pad switch assembly.


WIRING DIAGRAM

for A25A-FKS:
A402120E04
0.74,2.615 2.646,3 1.906,0.385 10 false Steering Pad Switch Assembly (Cruise Control Switch) 1.823,1.469 2.74,1.667 0.917,0.198 10 false CANCEL 0.5,1.479 1.417,1.677 0.917,0.198 10 false -SET 1.24,1.469 2.156,1.667 0.917,0.198 10 false +RES 2.521,1.479 3.438,1.677 0.917,0.198 10 false MAIN 2.75,0.75 3.667,0.948 0.917,0.198 10 false CCS 2.75,1.948 3.667,2.146 0.917,0.198 10 false ECC 3.219,0.875 4.135,1.073 0.917,0.198 10 false z1 3.219,2.073 4.135,2.271 0.917,0.198 10 false z1 3.26,0.615 4.177,0.813 0.917,0.198 10 false 2 3.219,1.823 4.135,2.021 0.917,0.198 10 false 12 3.74,0.771 4.656,0.969 0.917,0.198 10 false CCS 3.74,1.99 4.656,2.188 0.917,0.198 10 false ECC 4.333,0.885 5.25,1.083 0.917,0.198 10 false K22 4.333,2.083 5.25,2.281 0.917,0.198 10 false K22 4.375,0.656 5.292,0.854 0.917,0.198 10 false 13 4.427,1.854 5.344,2.052 0.917,0.198 10 false 2 3.198,2.583 5.104,2.969 1.906,0.385 10 false Spiral Cable Sub-assembly 5.708,0.875 6.625,1.073 0.917,0.198 10 false A24 5.719,2.083 6.635,2.281 0.917,0.198 10 false A24 5.719,2.844 6.635,3.042 0.917,0.198 10 false A24 5.76,0.646 6.677,0.844 0.917,0.198 10 false 27 5.76,1.854 6.677,2.052 0.917,0.198 10 false 28 5.75,2.625 6.667,2.823 0.917,0.198 10 false 10 6.115,0.885 7.031,1.083 0.917,0.198 10 false CCS 6.115,2.063 7.031,2.26 0.917,0.198 10 false ECCS 6.115,2.844 7.031,3.042 0.917,0.198 10 false E1 6.406,3.448 6.99,3.667 0.583,0.219 10 false ECM

for 2GR-FKS:
A408160E07
6.375,3.427 6.833,3.625 0.458,0.198 10 false ECM 6.01,3.427 6.469,3.625 0.458,0.198 10 false A23 5.854,0.76 6.313,0.958 0.458,0.198 10 false 41 6.094,0.885 6.552,1.083 0.458,0.198 10 false CCS 4.323,0.875 4.781,1.073 0.458,0.198 10 false K22 4.333,2.083 4.792,2.281 0.458,0.198 10 false K22 4.375,0.646 4.833,0.844 0.458,0.198 10 false 13 4.427,1.854 4.885,2.052 0.458,0.198 10 false 2 3.25,2.604 4.948,2.99 1.698,0.385 10 false Spiral Cable Sub-assembly 3.75,1.99 4.208,2.188 0.458,0.198 10 false ECC 3.74,0.771 4.198,0.969 0.458,0.198 10 false CCS 3.229,0.885 3.688,1.083 0.458,0.198 10 false z1 3.229,2.083 3.688,2.281 0.458,0.198 10 false z1 3.229,1.854 3.688,2.052 0.458,0.198 10 false 12 3.271,0.656 3.729,0.854 0.458,0.198 10 false 2 0.823,2.583 2.781,2.917 1.958,0.333 10 false Steering Pad Switch Assembly (Cruise Control Switch) 2.76,1.958 3.219,2.156 0.458,0.198 10 false ECC 2.76,0.781 3.219,0.979 0.458,0.198 10 false CCS 0.458,1.5 0.917,1.698 0.458,0.198 10 false -SET 1.24,1.49 1.698,1.688 0.458,0.198 10 false +RES 1.833,1.49 2.583,1.74 0.75,0.25 10 false CANCEL 2.49,1.49 3.24,1.74 0.75,0.25 10 false MAIN

for 6AR-FSE:
A402120E12
0.74,2.615 2.646,3 1.906,0.385 10 false Steering Pad Switch Assembly (Cruise Control Switch) 1.823,1.469 2.74,1.667 0.917,0.198 10 false CANCEL 0.5,1.479 1.417,1.677 0.917,0.198 10 false -SET 1.24,1.469 2.156,1.667 0.917,0.198 10 false +RES 2.521,1.479 3.438,1.677 0.917,0.198 10 false MAIN 2.75,0.75 3.667,0.948 0.917,0.198 10 false CCS 2.75,1.948 3.667,2.146 0.917,0.198 10 false ECC 3.219,0.875 4.135,1.073 0.917,0.198 10 false z1 3.219,2.073 4.135,2.271 0.917,0.198 10 false z1 3.26,0.635 4.177,0.833 0.917,0.198 10 false 2 3.219,1.823 4.135,2.021 0.917,0.198 10 false 12 3.74,0.771 4.656,0.969 0.917,0.198 10 false CCS 3.74,1.99 4.656,2.188 0.917,0.198 10 false ECC 4.333,0.875 5.25,1.073 0.917,0.198 10 false K22 4.375,0.656 5.292,0.854 0.917,0.198 10 false 13 4.427,1.854 5.344,2.052 0.917,0.198 10 false 2 3.198,2.583 5.104,2.969 1.906,0.385 10 false Spiral Cable Sub-assembly 5.708,0.875 6.625,1.073 0.917,0.198 10 false A78 5.719,2.083 6.635,2.281 0.917,0.198 10 false A78 5.719,2.844 6.635,3.042 0.917,0.198 10 false C58 5.771,1.865 6.688,2.063 0.917,0.198 10 false 41 5.75,0.656 6.667,0.854 0.917,0.198 10 false 55 5.75,2.625 6.667,2.823 0.917,0.198 10 false 53 6.115,0.885 7.031,1.083 0.917,0.198 10 false CCS 6.115,2.063 7.031,2.26 0.917,0.198 10 false ECCS 6.115,2.844 7.031,3.042 0.917,0.198 10 false E1 6.406,3.448 6.99,3.667 0.583,0.219 10 false ECM 4.333,2.083 5.25,2.281 0.917,0.198 10 false K22

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS
a.
A401214C01
2.615,1.031 2.865,1.031 true 2.271,0.698 2.396,0.542 2.396,0.542 2.833,0.542 true 2.281,1.396 2.406,1.552 2.406,1.552 2.917,1.552 true 1.75,0.99 2.26,0.99 true 1.552,0.365 1.865,0.521 0.313,0.156 10 false *1 2.885,0.938 3.094,1.146 0.208,0.208 10 true *a 2.927,1.458 3.115,1.656 0.188,0.198 10 true *b 2.865,0.448 3.177,0.604 0.313,0.156 10 false *c 1.594,0.906 1.906,1.063 0.313,0.156 10 false *d
*1 Steering Pad Switch Assembly
*a Cruise Control Main Switch
*b -SET Switch
*c +RES Switch
*d CANCEL Switch


Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Check the Data List to confirm proper functioning of the steering pad switch assembly.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch pushed
OFF: CANCEL switch not pushed
-
-SET Switch -SET switch status ON or OFF ON: -SET switch pushed
OFF: -SET switch not pushed
-
+RES Switch +RES switch status ON or OFF ON: +RES switch pushed
OFF: +RES switch not pushed
-
Cruise Main Switch Operation Condition Cruise control main switch status ON or OFF ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed
-
Powertrain > Cruise Control > Data List
Tester Display
Cancel Switch
-SET Switch
+RES Switch
Cruise Main Switch Operation Condition
50003 374 18,19,20,41
OK:

The value of each measurement item changes according to the operation of the steering pad switch assembly.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the K22 spiral cable sub-assembly connector.


b.

Disconnect the A24 ECM connector (for A25A-FKS).


c.

Disconnect the A23 ECM connector (for 2GR-FKS).


d.

Disconnect the A78 ECM connector (for 6AR-FSE).


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for A25A-FKS):
Tester Connection Condition Specified Condition
A24-27 (CCS) - K22-13 (CCS) Always Below 1 Ω
A24-28 (ECCS) - K22-2 (ECC) Always Below 1 Ω
A24-27 (CCS) or K22-13 (CCS) - Body ground Always 10 kΩ or higher
A24-28 (ECCS) or K22-2 (ECC) - Body ground Always 10 kΩ or higher


Standard Resistance (for 2GR-FKS):
Tester Connection Condition Specified Condition
A23-41 (CCS) - K22-13 (CCS) Always Below 1 Ω
K22-2 (ECC) - Body ground Always Below 1 Ω
A23-41 (CCS) or K22-13 (CCS) - Body ground Always 10 kΩ or higher


Standard Resistance (for 6AR-FSE):
Tester Connection Condition Specified Condition
A78-55 (CCS) - K22-13 (CCS) Always Below 1 Ω
A78-41 (ECCS) - K22-2 (ECC) Always Below 1 Ω
A78-55 (CCS) or K22-13 (CCS) - Body ground Always 10 kΩ or higher
A78-41 (ECCS) or K22-2 (ECC) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for A25A-FKS, 6AR-FSE) A
OK (for 2GR-FKS) B
NG C



A

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the A24 ECM connector (for A25A-FKS).


b.

Disconnect the C58 ECM connector (for 6AR-FSE).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for A25A-FKS):
Tester Connection Condition Specified Condition
A24-10 (E1) - Body ground Always Below 1 Ω


Standard Resistance (for 6AR-FSE):
Tester Connection Condition Specified Condition
C58-53 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR