The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during spiral cable sub-assembly removal/installation are shown below.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)
3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 6AR-FSE: Click hereGeneral>MAINTENANCE>6AR-FSE BATTERY>REMOVAL
for 2AR-FE: Click hereGeneral>MAINTENANCE>2AR-FE BATTERY>REMOVAL
for A25A-FKS: Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>REMOVAL
for 2GR-FKS: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
45186
5.REMOVE LOWER NO. 2 STEERING WHEEL COVER
45130
6.REMOVE HORN BUTTON ASSEMBLY
45100
7.REMOVE STEERING WHEEL ASSEMBLY
45024
8.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)
45024
9.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)
45286B
10.REMOVE UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)
45286B
11.REMOVE UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)
12.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.
Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.
Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the front wheels are aligned facing straight ahead.
| *a | Slider |
|
Release in this Direction |
Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Disconnect the other connectors from the spiral cable with sensor sub-assembly.
|
Separate in this Direction |
Separate the wire harness from the spiral cable with sensor sub-assembly as shown in the illustration.
Disengage the claw and 2 clips to remove the spiral cable with sensor sub-assembly.
13.REMOVE SPIRAL CABLE SUB-ASSEMBLY
Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly or the steering sensor.
Removing the steering sensor from the spiral cable sub-assembly without using a lock pin may result in the center position of the steering sensor becoming misaligned. Therefore, make sure to use the lock pin provided with a new spiral cable sub-assembly when removing the steering sensor from the spiral cable sub-assembly.
When replacing the steering sensor:
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL
Install the lock pin to the steering sensor.
Use the lock pin provided with a new spiral cable sub-assembly.
Do not remove the lock pin before installing the steering sensor to the spiral cable sub-assembly.
| *a | Guide |
| *b | Pin |
Disengage the 6 claws and 2 pins to remove the spiral cable sub-assembly from the steering sensor.
Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.