Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2018.04–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake system warning light (red indicator) remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

The vacuum inside the brake booster decreases (except 2AR-FE).

·

EBD operation is not possible.


WIRING DIAGRAM

C375208E04
0.792,1.24 1.521,1.531 0.729,0.292 10 false CANL 1.26,1.042 1.656,1.292 0.396,0.25 10 false 31 1.271,1.646 1.667,1.896 0.396,0.25 10 false 32 5.75,1.063 6.146,1.313 0.396,0.25 10 false 19 5.802,1.635 6.198,1.885 0.396,0.25 10 false 5 5.75,2.188 6.146,2.438 0.396,0.25 10 false 30 5.74,2.875 6.135,3.125 0.396,0.25 10 false 36 5.74,3.74 6.135,3.99 0.396,0.25 10 false 46 6.031,2.292 6.427,2.542 0.396,0.25 10 false +BS 6.031,2.979 6.427,3.229 0.396,0.25 10 false IG1 6.042,3.854 6.51,4.083 0.469,0.229 10 false GND1 5.458,4.552 6.375,4.813 0.917,0.26 10 false A34 5.458,4.729 7.01,5.26 1.552,0.531 10 false Skid Control ECU (Brake Actuator Assembly) 4.417,2.469 5.271,2.74 0.854,0.271 10 false ABS NO. 2 4.302,3.167 5.396,3.417 1.094,0.25 10 false ECU-IG1 NO. 2 2.833,2.281 3.813,2.573 0.979,0.292 10 false from Battery 2.281,2.969 3.75,3.219 1.469,0.25 10 false from IG1-NO. 1 Relay 1.26,4.542 1.656,4.792 0.396,0.25 10 false 12 1.281,6.26 1.677,6.51 0.396,0.25 10 false 7 1.938,4.542 2.333,4.792 0.396,0.25 10 false 1 2.156,4.542 2.552,4.792 0.396,0.25 10 false + 2.958,4.552 3.354,4.802 0.396,0.25 10 false E 1.542,5.073 1.938,5.323 0.396,0.25 10 false A1 1.542,5.24 4.031,5.792 2.49,0.552 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 1.948,6.823 2.344,7.073 0.396,0.25 10 false A2 1.948,7 3.49,7.448 1.542,0.448 10 false Vacuum Warning Switch Assembly* 1.865,8.25 3.917,8.51 2.052,0.26 10 false : CAN Communication Line 0.219,7.385 1.406,7.802 1.188,0.417 10 false Combination Meter Assembly 0.771,1.833 1.5,2.125 0.729,0.292 10 false CANH 6.031,1.219 6.76,1.51 0.729,0.292 10 false CANL 0.229,7.219 0.625,7.469 0.396,0.25 10 false K21 6.052,1.813 6.781,2.104 0.729,0.292 10 false CANH 3.177,4.542 3.573,4.792 0.396,0.25 10 false 2 1.958,6.271 2.354,6.521 0.396,0.25 10 false 2 3.188,6.25 3.583,6.5 0.396,0.25 10 false 1 2.948,6.26 3.344,6.51 0.396,0.25 10 false E 2.156,6.271 2.552,6.521 0.396,0.25 10 false + 0.917,4.469 1.385,4.698 0.469,0.229 10 false SW 0.865,6.188 1.333,6.417 0.469,0.229 10 false VCM 4.333,8.24 6.385,8.5 2.052,0.26 10 false *: except 2AR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing this procedure, depress the brake pedal and confirm that the stop lights illuminate.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) terminal - Negative (-) terminal Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C360727C69
0.229,0.302 0.635,0.563 0.406,0.26 1.49,0.927 1.771,0.417 true 0.927,1.792 0.677,1.063 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.302,0.344 0.635,0.542 0.333,0.198 10 false A34 1.698,0.25 2.333,0.438 0.635,0.188 10 false IG1 0.833,1.823 1.563,2.021 0.729,0.198 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-30 (+BS) - Body ground Always 11 to 14 V
A34-36 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C360727C70
0.302,0.302 0.74,0.552 0.438,0.25 2.396,0.344 2.74,0.99 true 0.135,0.063 0.448,0.26 0.313,0.198 10 false *a 0.385,0.333 0.698,0.531 0.313,0.198 10 false A34 2.219,0.177 2.719,0.385 0.5,0.208 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-46 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.
C230719C21
2,1.99 2.51,2.813 false 1.458,1.99 0.958,2.813 false 0.365,0.302 0.594,0.49 0.229,0.188 10 *a 2.563,2.844 2.719,3.031 0.156,0.188 10 + 0.844,2.865 1,3.052 0.156,0.188 10 E
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Turn the ignition switch off.


b.

Reconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Remove the reservoir filler cap and strainer.


d.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



e.

Disconnect the A1 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.


Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - 2 (E) Switch off (float up) 1.9 to 2.1 kΩ
1 (+) - 2 (E) Switch on (float down) Below 1 Ω



h.

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the K21 combination meter assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-12 (SW) - A1-1 (+) Always Below 1 Ω
K21-12 (SW) or A1-1 (+) - Body ground Always 10 kΩ or higher
A1-2 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (except 2AR-FE) A
OK (for 2AR-FE) B
NG C



A

8.INSPECT VACUUM WARNING SWITCH ASSEMBLY

B

11.READ VALUE USING GTS (BRAKE WARNING LIGHT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT VACUUM WARNING SWITCH ASSEMBLY
a.

Reconnect the A1 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


b.

Reconnect the K21 combination meter assembly connector.


c.

Inspect the vacuum warning switch assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH>ON-VEHICLE INSPECTION

OK:

The vacuum warning switch assembly is normal.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)

NG

REPLACE VACUUM WARNING SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A2 vacuum warning switch assembly connector.


c.

Disconnect the K21 combination meter assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-7 (VCM) - A2-2 (+) Always Below 1 Ω
K21-7 (VCM) or A2-2 (+) - Body ground Always 10 kΩ or higher
A2-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Reconnect the A2 vacuum warning switch assembly connector.


b.

Reconnect the K21 combination meter assembly connector.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Warning Light Brake system warning light (red indicator) ON or OFF ON: Warning light on
OFF: Warning light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Brake Warning Light
50003 105 52

d.

Check the GTS display condition of the brake system warning light (red indicator).


Result:
Result Proceed to
The value of Brake Warning Light is ON A
The value of Brake Warning Light is OFF B



A

B

11.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Reconnect the K21 combination meter assembly connector.


b.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Warning Light Brake system warning light (red indicator) ON or OFF ON: Warning light on
OFF: Warning light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Brake Warning Light
50003 105 52

c.

Check the GTS display condition of the brake system warning light (red indicator).


Result:
Result Proceed to
The value of Brake Warning Light is ON A
The value of Brake Warning Light is OFF B



A

B