Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065374 NAVIGATION / MULTI INFO DISPLAY _0328126 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Roof console box sub-assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

Telematics Transceiver

·

Harness or connector*



*: w/ Telematics Transceiver


WIRING DIAGRAM

w/ Sliding Roof
E368042E01
0.438,3.229 1.833,3.833 1.396,0.604 10 false Telephone Microphone Assembly 2.188,3.25 3.646,3.813 1.458,0.563 10 false Roof Console Box Sub-assembly 5.271,3.323 6.969,4 1.698,0.677 10 false Radio and Display Receiver Assembly 2.938,1.865 3.531,2.135 0.594,0.271 10 false SNS2 2.917,2.24 3.51,2.51 0.594,0.271 10 false MCO- 2.146,1.656 2.74,1.927 0.594,0.271 10 false 1 2.146,1.865 2.74,2.135 0.594,0.271 10 false B 3.427,1.865 4.021,2.135 0.594,0.271 10 false V14 2.156,2.063 2.75,2.333 0.594,0.271 10 false 2 3.51,1.646 4.104,1.917 0.594,0.271 10 false 6 2.99,2.667 3.583,2.938 0.594,0.271 10 false GND 5.625,1.875 6.219,2.146 0.594,0.271 10 false SNS2 5.625,2.271 6.219,2.542 0.594,0.271 10 false MIN- 5.365,1.76 5.958,2.031 0.594,0.271 10 false 25 5.365,2.135 5.958,2.406 0.594,0.271 10 false 22 5.281,3.156 5.875,3.427 0.594,0.271 10 false K2 2.156,2.26 2.75,2.531 0.594,0.271 10 false B 3.448,2.24 4.042,2.51 0.594,0.271 10 false V14 3.448,2.646 4.042,2.917 0.594,0.271 10 false V14 3.521,2.052 4.115,2.323 0.594,0.271 10 false 7 3.479,2.438 4.073,2.708 0.594,0.271 10 false 15

w/o Sliding Roof
E371449E17
5.427,2.156 6.615,2.688 1.188,0.531 10 false Radio and Display Receiver Assembly 2.323,2.01 3.438,2.635 1.115,0.625 10 false Roof Console Box Sub-assembly 0.458,2.052 1.885,2.531 1.427,0.479 10 false Telephone Microphone Assembly 0.448,4.729 1.875,5.208 1.427,0.479 10 false Telephone Microphone Assembly 4.177,4.49 5.24,4.854 1.063,0.365 10 false Telematics Transceiver 5.479,4.854 6.656,5.354 1.177,0.5 10 false Radio and Display Receiver Assembly 5.438,1.99 5.958,2.24 0.521,0.25 10 false K2 5.49,4.698 6.01,4.948 0.521,0.25 10 false K2 4.177,4.323 4.698,4.573 0.521,0.25 10 false K145 5.583,1.073 6.104,1.323 0.521,0.25 10 false MIN- 5.594,0.719 6.115,0.969 0.521,0.25 10 false SNS2 5.354,3.219 5.875,3.469 0.521,0.25 10 false 25 5.365,1 5.885,1.25 0.521,0.25 10 false 22 3.448,0.5 3.969,0.75 0.521,0.25 10 false 12 3.448,0.906 3.969,1.156 0.521,0.25 10 false 11 2.938,0.708 3.458,0.958 0.521,0.25 10 false SNS2 2.938,1.083 3.458,1.333 0.521,0.25 10 false MCO- 2.125,0.51 2.646,0.76 0.521,0.25 10 false 1 2.135,0.917 2.656,1.167 0.521,0.25 10 false 2 2.125,3.135 2.646,3.385 0.521,0.25 10 false 1 2.156,3.656 2.677,3.906 0.521,0.25 10 false 2 2.948,3.313 3.469,3.563 0.521,0.25 10 false SNS2 3.49,3.135 4.01,3.385 0.521,0.25 10 false 3 3.479,3.656 3.979,3.906 0.5,0.25 10 false 4 4.75,3.833 5.271,4.083 0.521,0.25 10 false MCO- 3.406,1.094 3.948,1.365 0.542,0.271 10 false V13 3.406,0.708 3.927,0.958 0.521,0.25 10 false V13 2.125,1.104 2.646,1.354 0.521,0.25 10 false B 2.125,0.708 2.646,0.958 0.521,0.25 10 false B 3.406,3.833 3.927,4.083 0.521,0.25 10 false V20 3.417,3.323 3.938,3.573 0.521,0.25 10 false V20 2.146,3.844 2.667,4.094 0.521,0.25 10 false B 2.125,3.313 2.646,3.563 0.521,0.25 10 false B 5.594,3.875 6.115,4.125 0.521,0.25 10 false MIN- 5.604,3.333 6.125,3.583 0.521,0.25 10 false SNS2 5.385,3.74 5.906,3.99 0.521,0.25 10 false 22 5.146,3.75 5.667,4 0.521,0.25 10 false 19 4.021,3.708 4.542,3.958 0.521,0.25 10 false 35 4.208,3.854 4.729,4.104 0.521,0.25 10 false MCI- 2.917,3.823 3.438,4.073 0.521,0.25 10 false MCO- 5.354,0.594 5.875,0.844 0.521,0.25 10 false 25 3,1.49 3.521,1.74 0.521,0.25 10 false GND 3.406,1.5 3.927,1.75 0.521,0.25 10 false V13 3.49,1.302 4.01,1.552 0.521,0.25 10 false 4 3.01,4.292 3.531,4.542 0.521,0.25 10 false GND 3.406,4.292 3.927,4.542 0.521,0.25 10 false V20 3.458,4.115 3.979,4.365 0.521,0.25 10 false 11 0.042,0.042 2.417,0.313 2.375,0.271 12 false w/o Telematics Transceiver: 0.073,2.667 2.448,2.938 2.375,0.271 12 false w/ Telematics Transceiver: 2.344,4.708 3.458,5.333 1.115,0.625 10 false Roof Console Box Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.




PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E360498C04
1.531,0.729 1.896,1.01 0.365,0.281 2.813,2.604 2.052,2.156 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.635,0.792 1.948,0.99 0.313,0.198 10 false K2 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-22 (MIN-) - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK (w/ Sliding Roof) A
OK (w/o Sliding Roof and w/o Telematics Transceiver) B
OK (w/o Sliding Roof and w/ Telematics Transceiver) C
NG D




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

C

8.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX SUB-ASSEMBLY)

D

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V14 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V14-6 (SNS2) Always Below 1 Ω
K2-22 (MIN-) - V14-7 (MCO-) Always Below 1 Ω
K2-25 (SNS2) or V14-6 (SNS2) - Body ground Always 10 kΩ or higher
K2-22 (MIN-) or V14-7 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect the B telephone microphone assembly connector.


c.
E360501C01
1.76,1.24 1.688,0.698 false 1.969,1.24 2.208,0.719 false 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.521,0.531 1.948,0.74 0.427,0.208 10 false MCO- 2.104,0.552 2.531,0.771 0.427,0.219 10 false SNS2
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
4.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371472C04
1.427,2.781 1.885,3.042 0.458,0.26 1.563,0.427 2.021,0.688 0.458,0.26 1.823,1.583 1.563,0.875 false 1.969,1.583 2.229,0.885 false 2.448,2.448 2.708,1.75 false 1.167,0.781 1.677,1.052 0.51,0.271 10 false MCO- 0.188,0.24 0.5,0.438 0.313,0.198 10 false *a 0.219,2.708 0.531,2.906 0.313,0.198 10 false *b 1.646,0.479 2.125,0.698 0.479,0.219 10 false V14 1.583,2.823 2.063,3.042 0.479,0.219 10 false B 2.302,0.781 2.844,1 0.542,0.219 10 false SNS2 2.135,2.396 2.677,2.615 0.542,0.219 10 false GND
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - V14-6 (SNS2) Always Below 1 Ω
B-2 - V14-7 (MCO-) Always Below 1 Ω
B-1 or V14-6 (SNS2) - V14-15 (GND) Always 10 kΩ or higher
B-2 or V14-7 (MCO-) - V14-15 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V13 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V13-12 (SNS2) Always Below 1 Ω
K2-22 (MIN-) - V13-11 (MCO-) Always Below 1 Ω
K2-25 (SNS2) or V13-12 (SNS2) - Body ground Always 10 kΩ or higher
K2-22 (MIN-) or V13-11 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect the B telephone microphone assembly connector.


c.
E360499C01
1.74,1.698 1.573,1.385 false 1.219,1.719 1.458,1.385 false 0.25,0.156 0.563,0.354 0.313,0.198 10 false *a 1.031,1.719 1.479,1.958 0.448,0.24 10 false SNS2 1.667,1.698 2.156,1.958 0.49,0.26 10 false MCO-
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (SNS2) - 11 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

7.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
7.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371473C10
1.458,2.75 1.885,3.01 0.427,0.26 1.417,0.563 1.844,0.823 0.427,0.26 1.042,1.531 0.771,0.969 false 1.396,2.073 1.51,1.729 false 1.865,2.177 1.625,1.74 false 0.26,0.292 0.573,0.49 0.313,0.198 10 false *a 0.281,2.74 0.594,2.938 0.313,0.198 10 false *b 1.052,2.083 1.563,2.365 0.51,0.281 10 false SNS2 1.917,2.094 2.427,2.375 0.51,0.281 10 false MCO- 0.448,0.875 0.958,1.156 0.51,0.281 10 false GND 1.5,0.625 2.01,0.906 0.51,0.281 10 false V13 1.625,2.813 2.135,3.094 0.51,0.281 10 false B
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - V13-12 (SNS2) Always Below 1 Ω
B-2 - V13-11 (MCO-) Always Below 1 Ω
B-1 or V13-12 (SNS2) - V13-4 (GND) Always 10 kΩ or higher
B-2 or V13-11 (MCO-) - V13-4 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K145 telematics transceiver connector.


b.

Disconnect the V20 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K145-35 (MCI-) - V20-4 (MCO-) Always Below 1 Ω
K145-35 (MCI-) or V20-4 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the K145 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-22 (MIN-) - K145-19 (MCO-) Always Below 1 Ω
K2-22 (MIN-) or K145-19 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V20 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V20-3 (SNS2) Always Below 1 Ω
K2-25 (SNS2) or V20-3 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT TELEMATICS TRANSCEIVER
a.

Connect the K145 telematics transceiver connector.


b.

Connect the K2 radio and display receiver assembly connector.


c.
E266270C36
1.521,0.594 2.021,0.844 0.5,0.25 0.99,2.604 1.24,2.031 false 1.594,0.635 2.052,0.875 0.458,0.24 10 false K145 0.854,2.646 1.302,2.885 0.448,0.24 10 false MCI- 0.198,0.177 0.51,0.375 0.313,0.198 10 false *a
*a Component with harness connected
(Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K145-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

12.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect the B telephone microphone assembly connector.


c.
E360500C02
1.927,1.229 1.479,0.698 false 2.104,1.219 2.583,0.719 false 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 1.302,0.521 1.813,0.729 0.51,0.208 10 false MCO- 2.438,0.542 2.969,0.802 0.531,0.26 10 false SNS2
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SNS2) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

13.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
13.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E369493C34
1.458,0.396 1.844,0.646 0.385,0.25 1.479,2.813 1.875,3.063 0.396,0.25 2.542,2.156 2.333,1.708 false 1.896,1.438 1.396,0.927 false 2.052,1.438 2.479,0.927 false 0.521,0.385 0.833,0.583 0.313,0.198 10 false *a 0.521,2.719 0.833,2.917 0.313,0.198 10 false *b 2.354,0.75 2.854,0.969 0.5,0.219 10 false SNS2 1.198,0.75 1.677,0.958 0.479,0.208 10 false MCO- 2.438,2.188 2.927,2.417 0.49,0.229 10 false GND 1.635,2.854 1.948,3.052 0.313,0.198 10 false B 1.521,0.448 2,0.656 0.479,0.208 10 false V20
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - V20-3 (SNS2) Always Below 1 Ω
B-2 - V20-4 (MCO-) Always Below 1 Ω
B-1 or V20-3 (SNS2) - V20-11 (GND) Always 10 kΩ or higher
B-2 or V20-4 (MCO-) - V20-11 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY