Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for 6AR-FSE) › 2018.04–2021.02
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0351287 COMPRESSOR(for 6AR-FSE) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 6AR-FSE)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.

When replacing the compressor assembly with magnetic clutch with a new one:

i.
E381589C01
1.115,1.802 1.115,0.969 true 1.021,1.813 1.333,1.969 0.313,0.156 10 false *a
*a Drain Bolt (Seal Washer)


Remove the drain bolt (seal washer) from a new compressor assembly with magnetic clutch.


ii.
E218352C07
0.125,0.125 0.302,0.313 0.177,0.188 10 false *a 1.438,1.375 1.625,1.542 0.188,0.167 10 true *b 1.479,1.625 1.667,1.802 0.188,0.177 10 true A 2.396,1.375 2.583,1.531 0.188,0.156 10 true *c
*a Removed Compressor
*b Amount of oil to be drained from removed compressor assembly with magnetic clutch
*c Amount of oil remaining in the reserve chamber (60 cc (2.03 fl.oz))


Gradually discharge the inert gas from the service valve of the new compressor assembly with magnetic clutch. Then drain the following amount of oil from the new compressor before installation so that the amount of oil contained in it is the same as that in the compressor to be replaced.

HINT:

New compressors are filled with sufficient oil for the whole air conditioning system. Therefore, it is necessary to drain oil from the new compressor to compensate for oil remaining in the condenser and cooling unit.


Standard:

(The amount of compressor oil inside a new compressor assembly with magnetic clutch: 70 (+15) cc (2.37 (+0.51) fl.oz)) - (The amount of compressor oil remaining in the removed compressor assembly with magnetic clutch) = The amount of compressor oil to be removed when replacing the compressor assembly with magnetic clutch.


NOTICE:
·

When A + 60 cc (2.03 fl.oz) exceeds the standard oil fill volume specified for the compressor by part number, install the compressor without adjusting the oil volume.

Example:

If A = 45 cc (1.52 fl.oz), A + 60 cc (2.03 fl.oz) = 105 cc (3.55 fl.oz). If the standard volume is 70 (+15) cc (2.37 (+0.51) fl.oz)), install the compressor as is.

·

If the amount of compressor oil remaining in the removed compressor assembly with magnetic clutch is excessively low, check for compressor oil leaks.

·

Make sure to use ND-OIL 8 or equivalent compressor oil.




iii.

Install the drain bolt (seal washer).

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)



b.

If draining the oil is difficult, drain the oil using the following procedure:

i.

Remove the suction seal cap.


ii.
E363442

Lightly shake the compressor assembly with magnetic clutch with the suction port facing down, and drain the oil (*1).

NOTICE:

Do not allow the pulley to come into contact with the compressor oil.




c.
E363443

With the pulley facing down, rotate the pulley as shown in the illustration 10 times at a rate of approximately once every 2 seconds (*2).

CAUTION:

If the pulley is rotated, refrigerant or oil may spray out. Thus, keep your face away from the compressor port.



d.
E363444

Rotate the pulley once as shown in the illustration while quickly turning the compressor up (*3).


e.

Perform step (*1) and drain the oil (*4).


f.

Drain the oil by repeating steps (*2) to (*4) approximately 5 times.


Hide 88310E 2.INSTALL COMPRESSOR ASSEMBLY WITH MAGNETIC CLUTCH

a.

for Type A:

i.

Using an E8 "TORX" socket wrench, temporarily install the compressor assembly with magnetic clutch with the 2 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.
E381581C02
2.094,1.677 2.156,1.938 true 2.083,1.938 2.396,2.094 0.313,0.156 10 false *a 1.198,0.188 1.396,0.365 0.198,0.177 10 true 1 1.781,1.979 1.979,2.156 0.198,0.177 10 false 2 0.896,1.771 1.094,1.948 0.198,0.177 10 false 3 2.219,0.302 2.417,0.479 0.198,0.177 10 true 4
*a Bracket
V100135

Bolt
V100136

Nut


Install the compressor assembly with magnetic clutch and bracket with the 2 bolts and 2 nuts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolts and nuts in the order shown in the illustration to install the compressor assembly with magnetic clutch.




b.

for Type B:

i.
E381582C02
2.063,1.646 2.146,1.938 true 2.063,1.948 2.375,2.104 0.313,0.156 10 false *a 0.906,1.719 1.208,1.906 0.302,0.188 10 false 3 1.771,1.958 2.073,2.146 0.302,0.188 10 false 2 1.198,0.167 1.375,0.344 0.177,0.177 10 true 1 2.208,0.302 2.385,0.479 0.177,0.177 10 true 4
*a Bracket


Install the compressor assembly with magnetic clutch and bracket with the 4 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration to install the compressor assembly with magnetic clutch.




c.

Engage each clamp.


d.

Connect each connector.


Hide 88704 3.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction hose sub-assembly to the compressor assembly with magnetic clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 1 cooler refrigerant discharge hose sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the No. 1 cooler refrigerant discharge hose sub-assembly to the compressor assembly with magnetic clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 17750A 5.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 6.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 16361A 7.INSTALL V-RIBBED BELT

Hide 8.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT