Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS) › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _072211 TELEMATICS _0351443 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B1573  Disconnect/Short in Telephone Antenna Circuit  B15CB  Telephone Antenna Disconnected  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the roof antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1573 Disconnect/Short in Telephone Antenna Circuit Roof antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the engine switch is on (IG)
(Short circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

Antenna cord sub-assembly (for Type A)

·

No. 2 antenna cord sub-assembly

·

No. 5 antenna cord sub-assembly


B15CB Telephone Antenna Disconnected Roof antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the engine switch is on (IG)
(Open circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

Antenna cord sub-assembly (for Type A)

·

No. 2 antenna cord sub-assembly

·

No. 5 antenna cord sub-assembly



WIRING DIAGRAM

E338340E28
0.292,1.219 1.906,1.552 1.615,0.333 10 false Roof Antenna Assembly 0.281,1.052 0.438,1.25 0.156,0.198 10 false G 1.135,0.438 1.292,0.635 0.156,0.198 10 false 4 2.5,0.354 2.656,0.552 0.156,0.198 10 false 3 2.885,0.354 3.042,0.552 0.156,0.198 10 false 3 4.365,0.365 4.521,0.563 0.156,0.198 10 false 5 4.75,0.365 4.906,0.563 0.156,0.198 10 false 5 1.625,0.688 1.833,0.875 0.208,0.188 10 false *3 3.583,0.688 3.792,0.875 0.208,0.188 10 false *2 5.427,0.688 5.635,0.875 0.208,0.188 10 false *1 5.927,0.458 6.135,0.646 0.208,0.188 10 false 1 2.49,0.563 2.646,0.76 0.156,0.198 10 false F 2.896,0.563 3.052,0.76 0.156,0.198 10 false E 4.76,0.563 4.938,0.75 0.177,0.188 10 false C 4.365,0.563 4.521,0.76 0.156,0.198 10 false D 6.125,0.563 6.479,0.76 0.354,0.198 10 false TEL 6.094,1.042 6.281,1.229 0.188,0.188 10 false A 6.083,1.208 6.792,1.625 0.708,0.417 10 false Telematics Transceiver 1.573,2.229 4.427,2.458 2.854,0.229 10 false *1: Antenna Cord Sub-assembly (for Type A) 1.573,2.667 4.031,2.875 2.458,0.208 10 false *2: No. 2 Antenna Cord Sub-assembly 1.583,3.094 4.042,3.302 2.458,0.208 10 false *3: No. 5 Antenna Cord Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 233

f.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT ROOF ANTENNA ASSEMBLY
2.INSPECT ROOF ANTENNA ASSEMBLY
a.

Remove the roof antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.
E271865C14
1.969,1.479 2.229,1.729 false 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.26,1.708 2.573,1.906 0.313,0.198 10 false 4a
*a Component without harness connected
(Roof Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY

NG

3.INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY
a.

Remove the No. 5 antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA CORD>REMOVAL


b.
E170182C30
1.615,0.177 1.948,0.427 0.333,0.25 1.781,1.844 1.781,1.531 false 0.083,0.052 0.26,0.219 0.177,0.167 10 false *a 1.719,0.219 1.896,0.385 0.177,0.167 10 false F 1.729,1.875 2.031,2.094 0.302,0.219 10 false 3a
*a Component without harness connected
(No. 5 Antenna Cord Sub-assembly)


E271898C16
0.99,0.781 1.344,1.01 0.354,0.229 1.198,1.333 1.552,1.115 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.104,0.802 1.417,1 0.313,0.198 10 false G 1.021,1.302 1.333,1.5 0.313,0.198 10 false 4a
*a Component without harness connected
(No. 5 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F-3 - G-4 Always Below 1 Ω
F-3a - G-4a Always Below 1 Ω
F-3 or G-4 - Body ground Always 10 kΩ or higher
F-3a or G-4a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 5 ANTENNA CORD SUB-ASSEMBLY

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Remove the No. 2 antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


b.
B278874C11
1.552,0.229 1.885,0.479 0.333,0.25 1.885,1.417 2.417,1.417 false 0.156,0.125 0.354,0.344 0.198,0.219 10 false *a 2.469,1.333 2.677,1.521 0.208,0.188 10 false 3a 1.656,0.26 2.156,0.51 0.5,0.25 10 false E
*a Component without harness connected
(No. 2 Antenna Cord Sub-assembly)


E215638C49
1.635,0.25 1.969,0.5 0.333,0.25 1.427,1.708 1.427,1.208 false 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 1.75,0.292 2.063,0.49 0.313,0.198 10 false D 1.354,1.729 1.667,1.927 0.313,0.198 10 false 5a
*a Component without harness connected
(No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-5 - E-3 Always Below 1 Ω
D-5a - E-3a Always Below 1 Ω
D-5 or E-3 - Body ground Always 10 kΩ or higher
D-5a or E-3a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type A)

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

5.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type A)
a.

Remove the antenna cord sub-assembly (for type A).

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


b.
E258653C33
1.542,0.323 1.896,0.552 0.354,0.229 1.344,1.74 1.688,1.375 false 2.24,1.729 1.906,1.375 false 1.656,0.354 1.813,0.552 0.156,0.198 10 false A 1.167,1.76 1.5,1.958 0.333,0.198 10 false TEL 2.198,1.76 2.531,1.958 0.333,0.198 10 false 1a 0.167,0.146 0.365,0.323 0.198,0.177 10 false *a
*a Component without harness connected
(Antenna Cord Sub-assembly (for Type A))


E356779C13
1.552,0.438 1.906,0.667 0.354,0.229 2.25,1.667 2.125,1.229 true 0.208,0.135 0.521,0.333 0.313,0.198 10 false *a 2.219,1.708 2.531,1.906 0.313,0.198 10 false 5a 1.688,0.479 2,0.677 0.313,0.198 10 false C
*a Component without harness connected
(Antenna Cord Sub-assembly (for Type A))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (TEL) - C-5 Always Below 1 Ω
A-1a - C-5a Always Below 1 Ω
A-1 (TEL) or C-5 - Body ground Always 10 kΩ or higher
A-1a or C-5a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE TELEMATICS TRANSCEIVER

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (foe Type A)

6.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT