Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM D

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  CALIBRATION  


ADJUST PANORAMIC VIEW MONITOR SYSTEM


a.

This panoramic view monitor system can be set from the diagnostic screen of the radio and display receiver assembly.


b.

If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.

Part Name Operation Adjustment Item Proceed to
Steering sensor
·

Removal and installation of the steering sensor

·

Removal and installation of the connector of the steering sensor

·

Replacement


Steering angle neutral point (Initialize panoramic view monitor system) (Click here)
Procedure 9
Television camera controller Replacement Television camera controller initialization Procedure 2
Procedure 7
Procedure 8
Adjust steering angle Procedure 9
Suspension, tires, etc. The vehicle height changes because of suspension or tire replacement Television camera controller initialization Procedure 2
Procedure 7
Procedure 8
Adjust steering angle Procedure 9
Rear television camera assembly optical axis (Back camera position setting) Procedure 10
Rear television camera assembly
·

Replacement

·

Installation angle of the rear television camera changes because of the removal and installation of the rear television camera, etc.


Rear television camera view adjustment Procedure 2
Procedure 4
Procedure 8
Rear television camera assembly optical axis (Back camera position setting) Procedure 10
·

Front television camera assembly

·

Front bumper assembly

·

Radiator grille


·

Replacement

·

Installation angle of the front television camera changes because of the removal and installation of the front television camera, etc.


Front television camera view adjustment Procedure 2
Procedure 3
Procedure 8
Side television camera assembly LH
Outer rear view mirror assembly with cover LH
·

Replacement

·

Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.


Side television camera view adjustment Procedure 2
Procedure 5
Procedure 8
Side television camera assembly RH
Outer rear view mirror assembly with cover RH
·

Replacement

·

Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.


Side television camera view adjustment Procedure 2
Procedure 6
Procedure 8
·

Front television camera assembly, front bumper assembly or radiator grille

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly with cover LH

·

Side television camera assembly RH or outer rear view mirror assembly with cover RH


Replacement or removal and installation of 2 or more parts Television camera view adjustment Procedure 2
Procedure 7
Procedure 8
Rear television camera assembly optical axis (Back camera position setting)* Procedure 10

*: Applies only for when removing and installing or replacing the rear television camera assembly.


HINT:

The adjustment values stored while performing panoramic view monitor system calibration are stored in the television camera controller.




Procedure 1: PRE-WORK CHECKS


a.

Preliminary checks

NOTICE:
·

Provide shadow to prevent back-up light from hitting the camera.

·

Use string that does not stretch.

·

Apply pieces of adhesive tape to serve as check markers. When placing the markers, make them 100 mm (3.94 in.) wide.



i.

Perform the work at a wide, level location (4000 to 7300 mm [13.12 to 23.94 ft.]).


ii.

Park the vehicle on a flat surface with the steering wheel centered.

NOTICE:

Before stopping the vehicle, move the vehicle backward and forward to ensure that both the steering wheel and the tires point straight ahead.



iii.

Adjust the tire pressure to the specified value(s).


iv.

Remove all luggage from the vehicle before starting work.



b.

Marker locations

i.

Secure the string to the locations required to make the checks and set markers as shown in the illustration.

·
E287135C01
0.479,0.698 0.844,1.146 false 2.229,0.469 1.844,1.115 false 2.302,1.333 2.552,1.708 false 1.104,1.333 0.854,1.74 false 2.01,4.052 1.708,3.688 false 2.573,3.49 2.271,3.083 false 0.292,0.583 0.75,0.781 0.458,0.198 10 false *e 2.302,0.396 3.188,0.677 0.885,0.281 10 false *b 0.729,1.76 0.948,2 0.219,0.24 10 false *a 2.063,4 2.521,4.198 0.458,0.198 10 false *d 2.615,3.5 3.073,3.698 0.458,0.198 10 false *c 2.531,1.75 2.75,1.99 0.219,0.24 10 false *a
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3


Front camera adjustment only

·
E287136C01
1.719,1.042 2.073,0.563 false 2.552,3.135 2.781,2.729 false 2.375,3.823 2.5,4.01 false 0.958,3.823 0.708,4.094 false 1.521,3.813 1.521,4.292 false 0.552,3.49 0.76,3.792 false 2.146,0.469 2.604,0.667 0.458,0.198 10 false *d 0.385,3.406 0.844,3.604 0.458,0.198 10 false *e 0.563,4.094 1.25,4.458 0.688,0.365 10 false *a 2.458,4.042 3.146,4.406 0.688,0.365 10 false *a 1.427,4.344 2.365,4.552 0.938,0.208 10 false *b 2.823,2.635 3.323,2.854 0.5,0.219 10 false *c
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 4


Rear camera adjustment only

·
E287137C01
1.063,0.917 0.688,0.563 false 2.281,0.958 2.688,0.656 false 2.271,2.906 2.625,2.646 false 2.375,3.521 2.688,3.313 false 1.719,3.635 1.927,3.875 false 1.125,3.542 1.49,4.125 false 1.094,3.833 0.844,4.083 false 1.073,1.542 0.771,1.365 false 1.052,2.25 0.781,2.375 false 0.531,0.458 1.24,0.833 0.708,0.375 10 false *a 1.469,4.167 1.698,4.406 0.229,0.24 10 false *a 0.594,1.281 0.969,1.573 0.375,0.292 10 false *b 0.708,4.083 1.156,4.333 0.448,0.25 10 false *g 1.958,3.844 2.406,4.094 0.448,0.25 10 false *d 2.667,2.563 3.115,2.813 0.448,0.25 10 false *c 2.74,3.24 3.188,3.49 0.448,0.25 10 false *f 2.719,0.583 3.167,0.833 0.448,0.25 10 false *e 0.604,2.323 0.979,2.615 0.375,0.292 10 false *b
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3
*f String 4
*g String 5


Left camera adjustment only

·
E287138C01
0.573,0.438 0.854,0.906 false 2.615,0.563 2.344,0.854 false 2.594,3.781 2.313,3.74 false 2.271,3.521 1.844,4.188 false 1.708,3.615 1.365,3.844 false 0.969,3.479 0.75,3.229 false 0.885,2.865 0.667,2.615 false 2.615,1.188 2.344,1.479 false 2.677,2.427 2.344,2.167 false 2.646,0.5 3.344,0.844 0.698,0.344 10 false *a 1.74,4.188 2.104,4.448 0.365,0.26 10 false *a 2.635,1.094 2.979,1.385 0.344,0.292 10 false *b 0.406,0.323 0.792,0.542 0.385,0.219 10 false *e 0.51,2.49 0.896,2.708 0.385,0.219 10 false *c 0.594,3.125 0.979,3.344 0.385,0.219 10 false *f 1.188,3.792 1.573,4.01 0.385,0.219 10 false *d 2.635,3.729 3.021,3.948 0.385,0.219 10 false *g 2.708,2.427 3.052,2.719 0.344,0.292 10 false *b
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3
*f String 4
*g String 6


Right camera adjustment only

·

Adjustment of 4 cameras

E287104C01
4.833,3.344 5.083,3 false 2.417,1.5 2.875,1.5 false 4.26,1.5 4.75,1.5 false 3.25,4.469 3.573,4.135 false 3.917,4.469 3.792,4.073 false 5,4.031 5.25,4.344 false 5,1.115 5.25,0.833 false 4.292,1.073 5,0.417 false 2.823,1.083 2.406,0.667 false 3.667,1.083 3.844,0.76 false 4.302,1.771 4.823,1.771 false 4.302,2.552 4.823,2.552 false 4.292,4.094 4.542,4.406 false 2.5,4.417 2.823,4.083 false 2.313,1.792 2.833,1.792 false 2.313,2.552 2.833,2.552 false 2.219,0.521 2.51,0.75 0.292,0.229 10 false *a 5.052,0.333 6.302,0.5 1.25,0.167 10 false *a 4.875,1.698 5.708,1.865 0.833,0.167 10 false *b 3.865,4.5 4.115,4.719 0.25,0.219 10 false *b 3.854,0.646 4.083,0.896 0.229,0.25 10 false *b 2.25,1.438 2.667,1.604 0.417,0.167 10 false *g 4.802,1.417 5.219,1.583 0.417,0.167 10 false *h 5.135,2.917 5.552,3.083 0.417,0.167 10 false *c 5.302,0.75 5.719,0.917 0.417,0.167 10 false *e 5.229,4.385 5.646,4.552 0.417,0.167 10 false *f 3.063,4.5 3.479,4.667 0.417,0.167 10 false *d 4.865,2.479 5.698,2.646 0.833,0.167 10 false *b 4.531,4.448 4.948,4.615 0.417,0.167 10 false *a 2.365,4.406 2.781,4.573 0.417,0.167 10 false *a 2.125,1.719 2.958,1.885 0.833,0.167 10 false *b 2.125,2.458 2.958,2.625 0.833,0.167 10 false *b
*a Cross Check Marker *b Check Marker
*c String 1 *d String 2
*e String 3 *f String 4
*g String 5 *h String 6





c.

Marker positions

i.

Set the check markers at the positions shown in the illustration.

E287105C01
1.594,2.135 1.594,1.938 1.594,1.938 1.927,1.938 false 1.594,4.073 1.594,3.875 1.594,3.875 1.927,3.875 false 3.76,0.5 3.76,0.198 3.76,0.198 4.094,0.198 false 4.927,3.281 4.927,3.125 4.927,3.125 4.646,3.125 false 3.385,0.5 3.385,0.198 3.385,0.198 3.073,0.198 false 5.5,3.073 5.5,2.917 5.5,2.917 5.219,2.917 false 6.073,2.75 6.073,2.594 6.073,2.594 5.792,2.594 false 6.656,2.531 6.656,2.375 6.656,2.375 6.375,2.375 false 3.313,5.094 3.406,4.99 false 3.167,5.458 3.24,5.333 false 3.802,5.104 3.729,4.99 false 4,5.469 3.927,5.333 false 1.51,2.167 1.823,2.365 0.313,0.198 10 false *a 1.531,4.104 1.844,4.302 0.313,0.198 10 false *b 3.073,5.479 3.385,5.677 0.313,0.198 10 false *c 3.938,5.479 4.25,5.677 0.313,0.198 10 false *c 4.865,3.302 5.177,3.5 0.313,0.198 10 false *e 6,2.76 6.313,2.958 0.313,0.198 10 false *g 6.583,2.573 6.896,2.771 0.313,0.198 10 false *h 4.135,0.125 4.448,0.323 0.313,0.198 10 false *d 3.208,5.125 3.521,5.323 0.313,0.198 10 false *d 2.885,0.135 3.198,0.333 0.313,0.198 10 false *d 3.74,5.125 4.052,5.323 0.313,0.198 10 false *d 5.438,3.115 5.75,3.313 0.313,0.198 10 false *f
*a 4800 mm (15.7 ft.) *b 1500 mm (4.92 ft.)
*c 1400 mm (4.60 ft.) *d 693 mm (2.27 ft.)
*e 1500 mm (4.92 ft.) *f 1700 mm (5.58 ft.)
*g 3000 mm (9.84 ft.) *h 3200 mm (10.5 ft.)





PROCEDURE 2: SET DATUM POINTS


a.

Extend the datum line (string 1).

i.
E372783C01
1.625,2.844 1.948,3.156 1.948,3.156 2.198,3.156 false 1.646,2.698 2.313,2.51 2.313,2.51 2.563,2.51 false 2.24,3.073 2.552,3.229 0.313,0.156 10 false *a 2.604,2.448 2.917,2.604 0.313,0.156 10 false *b
*a Mark A
*b Weight


Hang a weight with a pointed tip and accurately mark the center position on the road surface. (Mark A)

NOTICE:

Make sure that the weight hangs straight down from the string.



ii.

Repeat the procedure to mark the right side. (Mark B)


iii.
E287139C01
1.01,2.771 1.292,2.458 false 2.417,2.74 2.125,2.458 false 2.385,2.458 2.542,2.073 false 2.594,1.969 2.875,2.135 0.281,0.167 10 false *a 0.885,2.802 1.135,2.938 0.25,0.135 10 false *b 2.385,2.792 2.646,2.969 0.26,0.177 10 false *c
*a String 1
*b Mark A
*c Mark B


Secure string 1 so that it passes through marks A and B on the left and right sides.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.




b.

Extend the vehicle center line (string 2).

i.

Hang a weight with a pointed tip so that it passes through the center of the front television camera assembly and accurately mark the center position on the road surface. (Mark C)

E372790C01
3.073,2.156 3.24,2.156 3.24,2.156 3.802,2.396 false 1.552,1.521 1.927,1.885 1.927,1.885 2.094,1.885 true 1.083,1.563 1.25,1.563 1.25,1.563 1.542,1.115 true 1.635,1.01 1.938,0.635 1.938,0.635 2.104,0.635 true 3.844,2.51 4.146,2.615 4.146,2.615 4.313,2.615 true 2.156,0.563 2.385,0.75 0.229,0.188 10 true *1 0.906,1.479 1.167,1.688 0.26,0.208 10 true *a 2.875,2.083 3.188,2.24 0.313,0.156 10 false *b 2.156,1.802 2.469,1.958 0.313,0.156 10 true *c 4.344,2.531 4.656,2.688 0.313,0.156 10 false *d
*1 Front Television Camera Assembly - -
*a Center Point *b Weight
*c String *d Mark C



ii.

Hang a weight with a pointed tip from the center of the rear emblem and accurately mark the center position on the road surface. (Mark D)

E359639C02
2.698,2.479 3.146,2.385 false 2.708,2.625 3.156,2.667 false 5.167,1.073 5.781,1.229 false 5.167,0.677 5.771,0.552 true 5.802,0.458 6.115,0.615 0.313,0.156 10 false *a 3.188,2.313 3.5,2.469 0.313,0.156 10 false *b 5.823,1.167 6.135,1.323 0.313,0.156 10 false *c 3.208,2.594 3.365,2.75 0.156,0.156 10 false *d
*a Center *b Weight
*c String *d Mark D



iii.
E287140C01
1.719,1.333 2.229,0.896 false 2.219,2.927 2.583,2.427 false 1,2.188 1.708,2.917 false 1.719,3.208 2.104,3.573 false 1.375,3.969 1.719,3.656 false 0.802,2.083 1.021,2.281 0.219,0.198 10 false *a 2.271,0.781 2.458,0.958 0.188,0.177 10 false *d 2.156,3.542 2.385,3.729 0.229,0.188 10 false *e 2.625,2.313 2.875,2.51 0.25,0.198 10 false *b 1.24,3.979 1.427,4.177 0.188,0.198 10 false *c
*a Datum Point
*b String 1
*c String 2
*d Mark C
*e Mark D


Secure string 2 so that it passes through marks C and D at the front and rear of the vehicle.

NOTICE:

When securing string 2, check that there is no slack and the string is not twisted.


HINT:

Set the point where strings 1 and 2 intersect as the datum point.





PROCEDURE 3: SET MARKERS (when checking front)


a.
E287141C01
1.719,1.208 2.24,0.76 false 2.594,3.448 2.333,3.156 false 2.01,4.104 1.708,3.76 false 1.125,3.781 1.323,3.781 1.323,3.781 1.719,3.156 false 0.583,1.917 0.771,1.74 0.771,1.74 0.99,1.74 false 1.031,1.667 1.281,1.865 0.25,0.198 10 false *a 2.302,0.677 2.583,0.875 0.281,0.198 10 false *e 2.635,3.479 2.865,3.656 0.229,0.177 10 false *c 2.063,4.125 2.281,4.292 0.219,0.167 10 false *d 0.958,3.708 1.208,3.885 0.25,0.177 10 false *b
*a 4800 mm (15.7 ft.)
*b Datum Point
*c String 1
*d String 2
*e Mark E


In front of the vehicle, extend string 3 perpendicular to the vehicle center line (string 2), and place a marker.

i.

Mark the position on string 2 in front of the vehicle, 4800 mm (15.7 ft.) from the datum point. (Mark E)


ii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iii.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



iv.
E287142C01
0.771,0.927 1.094,1.25 false 1.115,1.656 1.396,1.25 false 2.281,1.688 2.042,1.25 false 2.688,1.438 2.313,1.25 false 2.688,0.573 2.583,0.573 2.583,0.573 2.458,1.25 false 2.042,4.073 1.719,3.76 false 2.521,3.51 2.198,3.198 false 1.938,0.938 2.094,0.448 2.094,0.448 2.25,0.448 false 1.417,0.938 1.26,0.51 1.26,0.51 1.104,0.51 false 0.917,0.417 1.115,0.583 0.198,0.167 10 false *a 0.594,0.823 0.802,1.01 0.208,0.188 10 false *g 0.938,1.635 1.167,1.792 0.229,0.156 10 false *e 2.333,1.688 2.51,1.833 0.177,0.146 10 false *f 2.74,1.427 2.979,1.583 0.24,0.156 10 false *h 2.74,0.5 2.948,0.656 0.208,0.156 10 false *d 2.583,3.531 2.792,3.688 0.208,0.156 10 false *b 2.083,4.073 2.292,4.24 0.208,0.167 10 false *c 2.292,0.354 2.521,0.51 0.229,0.156 10 false *a
*a 1400 mm (4.60 ft.)
*b String 1
*c String 2
*d String 3
*e Mark F
*f Mark G
*g Mark H
*h Mark I


Secure string 3 so that it passes through marks F and G as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



v.

Mark positions on string 3, 1400 mm (4.60 ft.) to the left and right of the vehicle center line (string 2). (Marks H and I).


vi.
E287109C01
0.75,1.667 1.063,1.25 false 2.333,1.667 1.917,1.125 false 1.083,1.083 0.833,0.833 false 2.052,1.083 1.833,0.333 false 1.385,1.083 1.167,0.5 false 2.323,0.635 2.323,0.333 2.323,0.333 2.583,0.333 false 2.333,1.083 2.667,0.75 2.667,0.75 2.833,0.75 false 3.25,1.333 3.25,1.104 3.25,1.104 3.052,1.104 false 2.781,1.708 2.365,1.229 false 0.604,1.688 0.823,1.875 0.219,0.188 10 false *c 2.313,1.698 2.51,1.854 0.198,0.156 10 false *d 0.677,0.688 0.896,0.865 0.219,0.177 10 false *g 1.052,0.354 1.292,0.521 0.24,0.167 10 false *e 1.708,0.188 1.948,0.333 0.24,0.146 10 false *f 2.885,0.667 3.063,0.813 0.177,0.146 10 false *h 2.635,0.25 2.865,0.417 0.229,0.167 10 false *a 3.188,1.354 3.406,1.521 0.219,0.167 10 false *b 2.74,1.708 2.958,1.896 0.219,0.188 10 false *c
*a 800 mm (2.62 ft.)
*b 100 mm (0.33 ft.)
*c Cross Check Marker
*d Check Marker
*e Mark F
*f Mark G
*g Mark H
*h Mark I


Place and secure the cross check markers, centered on marks H and I.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.




vii.

Place the check marker between marks F and G.


viii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 4: SET MARKERS (When checking rear)


a.

To the rear of the vehicle, extend string 4 perpendicular to the vehicle center line (string 2), and place a check marker.

i.
E287143C01
1.719,1.104 2.208,0.854 false 0.948,2.26 1.167,2.26 1.167,2.26 1.719,2.844 false 1.229,4.021 1.688,3.573 false 0.698,3.104 0.896,3.104 0.896,3.104 1.094,3.271 false 2.74,3.24 2.552,2.833 false 0.531,3.031 1.604,3.229 1.073,0.198 10 false *a 1.063,3.99 1.542,4.25 0.479,0.26 10 false *e 0.792,2.198 1.615,2.458 0.823,0.26 10 false *b 2.271,0.802 3.094,1.063 0.823,0.26 10 false *d 2.75,3.26 3.229,3.521 0.479,0.26 10 false *c
*a 1500 mm (4.92 ft.)
*b Datum Point
*c String 1
*d String 2
*e Mark J


Mark a position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


ii.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


iii.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



iv.
E287144C01
1.708,0.896 2.208,0.542 false 0.583,2.063 1.094,2.688 false 1,3.052 1.396,3.354 false 0.677,3.802 1.094,3.354 false 2.385,3.042 2.073,3.344 false 2.875,3.646 2.677,3.344 false 2.615,3.802 2.313,3.344 false 2.167,3.969 1.969,3.667 false 1.188,3.979 1.417,3.667 false 2.292,0.5 2.75,0.698 0.458,0.198 10 false *c 0.385,1.969 0.844,2.167 0.458,0.198 10 false *b 0.844,2.938 1.302,3.135 0.458,0.198 10 false *f 2.438,2.969 2.896,3.167 0.458,0.198 10 false *e 2.844,3.698 3.302,3.896 0.458,0.198 10 false *d 2.542,3.854 3,4.052 0.458,0.198 10 false *h 2.167,4.042 3.104,4.26 0.938,0.219 10 false *a 1.115,4 2.052,4.219 0.938,0.219 10 false *a 0.552,3.833 1.01,4.031 0.458,0.198 10 false *g
*a 1400 mm (4.60 ft.)
*b String 1
*c String 2
*d String 4
*e Mark K
*f Mark L
*g Mark M
*h Mark N


Secure string 4 so that it passes through marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



v.

Mark positions on string 4, 1400 mm (4.60 ft.) to the left and right of the vehicle center line (string 2). (Marks M and N)


vi.
E287106C01
2.583,2.948 2.833,2.667 false 1.917,4.25 1.833,3.667 false 1.375,3.604 1.302,3.396 1.302,3.396 1.385,3.396 false 2.052,3.604 2.135,3.396 2.135,3.396 2.052,3.396 false 3.167,3.885 3.167,3.635 3.167,3.635 3.052,3.635 false 1.5,4 1.5,3.729 1.5,3.729 1.344,3.729 false 2.583,4.25 2.333,4.021 false 2.354,3.74 2.781,3.969 false 0.792,4.063 0.99,3.656 false 1.115,3.625 0.792,3.281 false 2.323,3.635 2.573,3.354 false 2.885,2.583 3.302,2.75 0.417,0.167 10 false *f 2.802,3.99 3.167,4.344 0.365,0.354 10 false *d 1.875,4.313 2.708,4.479 0.833,0.167 10 false *e 1.427,4.042 2.01,4.208 0.583,0.167 10 false *c 2.531,4.292 3.115,4.458 0.583,0.167 10 false *a 3.115,3.917 3.396,4.135 0.281,0.219 10 false *b 1.448,3.333 1.698,3.5 0.25,0.167 10 false *h 1.865,3.333 2.115,3.5 0.25,0.167 10 false *g 0.677,4.125 1.375,4.458 0.698,0.333 10 false *d 0.719,3.146 1.417,3.479 0.698,0.333 10 false *i 2.552,3.208 3.25,3.542 0.698,0.333 10 false *j
*a 800 mm (2.62 ft.)
*b 100 mm (0.33 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g Mark K
*h Mark L
*i Mark M
*j Mark N


Place and secure the cross check markers, centered on marks M and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




vii.

Place the check marker between marks K and L.


viii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 5: SET MARKERS (When checking left side)


a.

To the left side of the vehicle, extend string 5 perpendicular to the vehicle center line (string 2), and place a check marker.

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1500 mm (4.92 ft.)
*b 4800 mm (15.7 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string 2 in front of the vehicle, 4800 mm (15.7 ft.) from the datum point. (Mark E)


ii.

Mark the position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287146C01
0.563,0.5 1.094,1.073 false 1.135,1.438 1.406,1.063 false 2.042,1.052 2.177,0.583 false 2.552,1.063 2.792,0.594 false 2.583,3.719 2.74,3.958 false 2.052,3.719 2.208,3.958 false 1.104,3.417 1.385,3.708 false 0.781,4.073 1.083,3.708 false 1.365,4.021 1.469,4.281 false 1.365,0.771 1.438,0.438 false 0.385,0.417 0.698,0.615 0.313,0.198 10 false *f 1.385,0.26 2.021,0.469 0.635,0.208 10 false *a 0.99,1.469 1.302,1.667 0.313,0.198 10 false *d 2.156,0.427 2.469,0.625 0.313,0.198 10 false *e 2.781,0.427 3.188,0.667 0.406,0.24 10 false *b 2.719,3.99 3.125,4.229 0.406,0.24 10 false *c 2.156,3.99 2.469,4.188 0.313,0.198 10 false *g 1.427,4.313 2.063,4.521 0.635,0.208 10 false *a 0.656,4.094 1.063,4.365 0.406,0.271 10 false *i 0.938,3.323 1.25,3.521 0.313,0.198 10 false *h
*a 1400 mm (4.60 ft.)
*b String 3
*c String 4
*d Mark F
*e Mark G
*f Mark H
*g Mark K
*h Mark L
*i Mark M


Secure strings 3 and 4 so that they pass through marks F and G, marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark strings 3 and 4, 1400 mm (4.60 ft.) to the left of the vehicle center line (string 2). (Marks H and M)


ix.
E287147C04
0.771,0.771 1.385,1.021 false 0.781,0.385 1.396,0.635 false 1.406,1.531 1.24,1.365 false 1.385,1.677 1.229,1.792 false 1.385,2.208 1.188,2.083 false 1.396,2.354 1.281,2.51 false 2.531,2.979 2.656,3.219 false 1.385,3.594 1.563,3.75 false 0.24,2.354 0.125,2.354 0.125,2.354 0.125,2.635 false 0.51,2.354 0.396,2.354 0.396,2.354 0.396,2.635 false 0.802,2.354 0.688,2.354 0.688,2.354 0.688,2.635 false 1.063,2.51 0.948,2.51 0.948,2.51 0.948,2.792 false 0.615,0.313 1.073,0.51 0.458,0.198 10 false *f 0.604,0.677 0.917,0.885 0.313,0.208 10 false *g 1.104,1.24 1.563,1.438 0.458,0.198 10 false *l 1.073,1.792 1.531,1.99 0.458,0.198 10 false *k 1.073,1.969 1.531,2.167 0.458,0.198 10 false *j 1.208,2.552 1.667,2.75 0.458,0.198 10 false *i 2.625,3.281 3.083,3.479 0.458,0.198 10 false *e 1.615,3.771 2.073,3.969 0.458,0.198 10 false *h 0.865,2.781 1.802,3.052 0.938,0.271 10 false *a 0.594,2.698 1.531,2.969 0.938,0.271 10 false *b 0.333,2.677 1.271,2.948 0.938,0.271 10 false *c 0.042,2.677 0.313,2.896 0.271,0.219 10 false *d
*a 1500 mm (4.92 ft.)
*b 1700 mm (5.58 ft.)
*c 3000 mm (9.84 ft.)
*d 3200 mm (10.5 ft.)
*e String 1
*f String 5
*g Mark H
*h Mark M
*i Mark O
*j Mark P
*k Mark Q
*l Mark R


Secure string 5 so that it passes through marks H and M as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



x.

Make marks on string 5 that are 1500 mm (4.92 ft.), 1700 mm (5.58 ft.), 3000 mm (9.84 ft.), and 3200 mm (10.5 ft.) from the datum line (string 1) as shown in the illustration. (Marks O, P, Q and R)


xi.
E287107C01
1.094,3.615 0.75,3.333 false 1.438,0.167 1.104,0.167 1.104,0.167 1.104,0.396 false 2,0.5 1.135,0.917 false 1.073,3.75 0.667,4.25 false 1.583,4 1.583,3.74 1.583,3.74 1.438,3.74 false 0.885,1.219 1.104,1.031 false 1.104,0.667 0.667,0.5 false 2.583,3.031 2.833,2.74 false 0.885,2.604 1.115,2.406 false 0.875,2.052 1.115,2.229 false 1.229,1.896 1.115,1.75 false 1.333,1.396 1.115,1.573 false 0.365,1.031 0.198,1.031 0.198,1.031 0.198,1.5 false 1.063,2.323 0.813,2.323 false 1.073,1.667 0.823,1.667 false 1.49,0.083 2.073,0.25 0.583,0.167 10 false *b 0.49,0.406 0.906,0.573 0.417,0.167 10 false *g 2.052,0.417 3.302,0.583 1.25,0.167 10 false *d 0.646,2.25 1.479,2.417 0.833,0.167 10 false *e 0.573,4.271 2.073,4.438 1.5,0.167 10 false *d 0.594,3.229 0.927,3.396 0.333,0.167 10 false *i 1.51,4.042 2.094,4.208 0.583,0.167 10 false *c 2.885,2.604 3.302,2.771 0.417,0.167 10 false *f 0.719,1.25 1.052,1.417 0.333,0.167 10 false *h 1.292,1.25 1.625,1.417 0.333,0.167 10 false *m 1.177,1.927 1.51,2.094 0.333,0.167 10 false *l 0.75,1.906 1.083,2.073 0.333,0.167 10 false *k 0.792,2.646 1.125,2.813 0.333,0.167 10 false *j 0.146,1.552 0.729,1.719 0.583,0.167 10 false *a 0.594,1.583 1.427,1.75 0.833,0.167 10 false *e
*a 100 mm (0.33 ft.)
*b 800 mm (2.62 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g String 5
*h Mark H
*i Mark M
*j Mark O
*k Mark P
*l Mark Q
*m Mark R


Place and secure the cross check markers, centered on marks H and M.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




xii.

Place check markers between marks O and P, and marks Q and R.


xiii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 6: SET MARKERS (When checking right side)


a.

At the right side of the vehicle, extend string 6 parallel to the vehicle and place a marker.

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1500 mm (4.92 ft.)
*b 4800 mm (15.7 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string 2 in front of the vehicle, 4800 mm (15.7 ft.) from the datum point. (Mark E)


ii.

Mark the position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287712C01
0.927,0.49 1.344,1.052 false 2,1.063 2.229,1.469 false 2.313,1.063 2.792,0.385 false 2.5,1.063 2.896,1.323 false 2.813,3.615 2.906,3.354 false 2.313,3.635 2.573,3.948 false 2.01,3.615 2.219,3.354 false 1.354,3.625 1.125,3.344 false 1.969,3.938 2.094,4.188 false 1.99,0.76 2.146,0.448 false 2.115,0.313 3.188,0.51 1.073,0.198 10 false *a 2.052,4.229 3.125,4.427 1.073,0.198 10 false *a 0.708,0.385 1.021,0.583 0.313,0.198 10 false *d 2.833,0.24 3.146,0.438 0.313,0.198 10 false *f 2.969,1.302 3.417,1.531 0.448,0.229 10 false *b 2.26,1.5 2.573,1.698 0.313,0.198 10 false *e 2.948,3.271 3.396,3.5 0.448,0.229 10 false *c 2.271,3.271 2.583,3.469 0.313,0.198 10 false *g 2.594,3.979 2.906,4.177 0.313,0.198 10 false *i 0.896,3.219 1.208,3.417 0.313,0.198 10 false *h
*a 1400 mm (4.60 ft.)
*b String 3
*c String 4
*d Mark F
*e Mark G
*f Mark I
*g Mark K
*h Mark L
*i Mark N


Secure strings 3 and 4 so that they pass through marks F and G and marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark strings 3 and 4, 1400 mm (4.60 ft.) to the left of the vehicle center line (string 2). (Marks I and N)


ix.
E287713C01
2.01,0.781 2.365,0.573 false 1.823,0.729 2.021,1.021 false 2.26,1.333 2.021,1.531 false 2.229,1.833 2.031,1.667 false 1.885,2.01 2.01,2.219 false 1.896,2.531 2.01,2.344 false 0.656,3.125 0.771,3.125 0.771,3.125 0.875,2.969 false 2.99,2.76 2.99,2.563 2.99,2.563 3.167,2.563 false 1.854,3.792 2.01,3.615 false 2.448,2.75 2.448,2.552 2.448,2.552 2.604,2.552 false 2.729,2.75 2.729,2.552 2.729,2.552 2.885,2.552 false 2.177,2.74 2.177,2.542 2.177,2.542 2.333,2.542 false 1.646,0.615 1.958,0.813 0.313,0.198 10 false *g 2.427,0.51 2.958,0.75 0.531,0.24 10 false *f 2.313,1.229 2.625,1.427 0.313,0.198 10 false *l 2.219,1.865 2.531,2.063 0.313,0.198 10 false *k 1.813,1.844 2.125,2.042 0.313,0.198 10 false *j 1.833,2.552 2.146,2.75 0.313,0.198 10 false *i 0.438,3.042 0.906,3.292 0.469,0.25 10 false *e 1.677,3.76 1.99,3.958 0.313,0.198 10 false *h 2.927,2.792 3.26,3.021 0.333,0.229 10 false *d 2.677,2.792 2.969,3.031 0.292,0.24 10 false *c 2.104,2.792 3.063,3 0.958,0.208 10 false *a 2.385,2.792 3.344,3 0.958,0.208 10 false *b
*a 1500 mm (4.92 ft.)
*b 1700 mm (5.58 ft.)
*c 3000 mm (9.84 ft.)
*d 3200 mm (10.5 ft.)
*e String 1
*f String 6
*g Mark I
*h Mark N
*i Mark S
*j Mark T
*k Mark U
*l Mark V


Secure string 6 so that it passes through marks I and N as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



x.

Make marks on string 6 that are 1500 mm (4.92 ft.), 1700 mm (5.58 ft.), 3000 mm (9.84 ft.), and 3200 mm (10.5 ft.) from the datum line (string 1) as shown in the illustration. (Marks S, T, U and V)


xi.
E287108C01
1.5,0.583 2.292,0.917 false 2.563,1.406 2.323,1.573 false 2.615,1.896 2.323,1.76 false 2.198,2.583 2.333,2.406 false 2.74,3.375 2.365,3.25 false 3.167,1.333 3.167,1.031 3.167,1.031 3.063,1.031 false 2.5,3.021 2.75,2.729 false 2.323,0.667 2.75,0.333 false 2.323,0.396 2.323,0.167 2.323,0.167 2.083,0.167 false 1.99,3.74 1.833,3.74 1.833,3.74 1.833,4.25 false 2.333,3.615 2.552,3.927 false 2.198,2.01 2.333,2.229 false 2.333,1.01 2.75,0.667 false 2.656,1.667 2.354,1.667 false 2.656,2.302 2.354,2.302 false 1.292,0.51 2.542,0.677 1.25,0.167 10 false *d 2.719,1.604 3.333,1.76 0.615,0.156 10 false *e 2.74,3.375 3.125,3.646 0.385,0.271 10 false *d 1.781,4.292 2.365,4.458 0.583,0.167 10 false *c 2.604,3.927 2.938,4.094 0.333,0.167 10 false *i 2.802,2.583 3.219,2.75 0.417,0.167 10 false *f 3.104,1.385 3.417,1.594 0.313,0.208 10 false *a 2.802,0.583 3.135,0.75 0.333,0.167 10 false *h 2.802,0.25 3.219,0.417 0.417,0.167 10 false *g 1.917,0.104 2.5,0.271 0.583,0.167 10 false *b 2.583,1.323 2.917,1.49 0.333,0.167 10 false *m 2.656,1.865 2.99,2.031 0.333,0.167 10 false *l 2.135,1.844 2.385,2.042 0.25,0.198 10 false *k 2.135,2.625 2.469,2.792 0.333,0.167 10 false *j 2.698,2.229 3.313,2.385 0.615,0.156 10 false *e
*a 100 mm (0.33 ft.)
*b 800 mm (2.62 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g String 6
*h Mark I
*i Mark N
*j Mark S
*k Mark T
*l Mark U
*m Mark V


Place and secure the cross check markers, centered on marks I and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




xii.

Place check markers between marks S and T, and marks U and V.


xiii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 7: SET MARKERS (When checking all cameras)


a.

Set markers in every direction from the vehicle.

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1500 mm (4.92 ft.)
*b 4800 mm (15.7 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string 2 in front of the vehicle, 4800 mm (15.7 ft.) from the datum point. (Mark E)


ii.

Mark the position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287148C01
0.615,0.708 0.76,0.708 0.76,0.708 1.094,1.052 false 1.042,1.552 1.188,1.552 1.188,1.552 1.396,1.063 false 2.344,1.531 2.167,1.531 2.167,1.531 2.042,1.063 false 2.76,0.292 2.583,0.292 2.583,0.292 2.354,1.073 false 2.865,0.719 2.688,0.719 2.688,0.719 2.573,1.052 false 2.292,3.135 2.146,3.135 2.146,3.135 2.042,3.448 false 2.75,4.177 2.604,4.177 2.604,4.177 2.365,3.458 false 2.76,3.75 2.646,3.75 2.646,3.75 2.563,3.458 false 2.021,4.323 1.906,4.323 1.906,4.323 1.719,4.042 false 0.833,3.719 0.969,3.719 0.969,3.719 1.083,3.458 false 0.979,3.115 1.115,3.115 1.115,3.115 1.406,3.448 false 1.375,0.76 1.271,0.375 false 2,0.76 2.125,0.396 false 1.313,3.99 1.385,3.76 false 2.135,3.99 2.073,3.76 false 1.188,0.229 2.26,0.427 1.073,0.198 10 false *a 2.083,0.24 3.156,0.438 1.073,0.198 10 false *a 0.417,0.646 0.865,0.833 0.448,0.188 10 false *g 2.948,0.656 3.396,0.844 0.448,0.188 10 false *c 2.833,0.229 3.281,0.417 0.448,0.188 10 false *h 0.781,1.479 1.229,1.667 0.448,0.188 10 false *e 2.396,1.469 2.844,1.656 0.448,0.188 10 false *f 2.354,3.083 2.802,3.271 0.448,0.188 10 false *i 0.802,3.063 1.25,3.25 0.448,0.188 10 false *j 0.667,3.667 1.115,3.854 0.448,0.188 10 false *k 2.813,4.125 3.26,4.313 0.448,0.188 10 false *l 2.833,3.698 3.281,3.885 0.448,0.188 10 false *d 2.094,4.26 2.542,4.448 0.448,0.188 10 false *b 2.094,4.031 2.823,4.25 0.729,0.219 10 false *a 1.208,4.01 1.938,4.229 0.729,0.219 10 false *a
*a 1400 mm (4.60 ft.)
*b String 2
*c String 3
*d String 4
*e Mark F
*f Mark G
*g Mark H
*h Mark I
*i Mark K
*j Mark L
*k Mark M
*l Mark N


Secure strings 3 and 4 so that they pass through marks F, G, K and L as shown in the illustration.

NOTICE:

Secure strings 3 and 4 so that they pass through marks F, G, K and L as shown in the illustration.



viii.

Mark string 3, 1400 mm (4.60 ft.) to the left and right of the vehicle center line (string 2). (Marks H and I)


ix.

Mark string 4, 1400 mm (4.60 ft.) to the left and right of the vehicle center line (string 2). (Marks M and N)


x.
E287132C02
1.094,0.688 1.292,0.271 false 2.302,0.667 2.688,0.177 false 2.604,1 2.875,0.677 false 2.625,1.375 2.302,1.01 false 0.781,1.385 1.104,1 false 0.458,3.26 0.698,3.583 false 0.771,4.031 1.094,3.594 false 1.552,3.833 1.708,3.74 false 2.646,3.948 2.313,3.594 false 2.635,2.646 2.469,2.958 false 1.344,0.198 1.802,0.396 0.458,0.198 10 false *e 2.75,0.104 3.208,0.302 0.458,0.198 10 false *f 2.938,0.604 3.396,0.802 0.458,0.198 10 false *c 2.688,1.396 3.146,1.594 0.458,0.198 10 false *h 0.625,1.417 1.083,1.615 0.458,0.198 10 false *g 0.313,3.104 0.771,3.302 0.458,0.198 10 false *d 0.646,4.073 1.104,4.271 0.458,0.198 10 false *i 1.375,3.875 1.833,4.073 0.458,0.198 10 false *b 2.667,4 3.125,4.198 0.458,0.198 10 false *j 2.729,2.573 3.188,2.771 0.458,0.198 10 false *a
*a String 1
*b String 2
*c String 3
*d String 4
*e String 5
*f String 6
*g Mark H
*h Mark I
*i Mark M
*j Mark N


Secure strings 5 and 6 so that they pass through marks H, M, I and N as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



xi.
E288356C02
2.542,3.885 2.354,3.885 2.354,3.885 2.281,3.604 false 0.396,3.26 0.531,3.26 0.531,3.26 0.552,2.979 false 2.344,2.615 2.188,2.615 2.188,2.615 2.177,2.75 false 2.594,2.615 2.479,2.615 2.479,2.615 2.469,2.75 false 2.875,2.615 2.74,2.615 2.74,2.615 2.729,2.75 false 3.167,2.625 3.031,2.625 3.031,2.625 3.021,2.76 false 0.781,0.75 0.635,0.5 0.635,0.5 0.479,0.5 false 1.396,0.76 1.25,0.51 1.25,0.51 1.094,0.51 false 2.021,0.719 2.146,0.458 2.146,0.458 2.385,0.458 false 2.344,1.021 2.469,0.76 2.469,0.76 2.708,0.76 false 2.021,1.521 2.115,1.313 2.115,1.313 2.24,1.313 false 2.031,2.208 2.125,2 2.125,2 2.25,2 false 0.792,1.531 0.677,1.333 0.677,1.333 0.479,1.333 false 0.792,2.208 0.677,2.01 0.677,2.01 0.479,2.01 false 0.771,2.354 0.688,2.5 0.688,2.5 0.542,2.5 false 0.781,1.688 0.698,1.833 0.698,1.833 0.552,1.833 false 1.906,1.865 2.021,1.677 false 1.896,2.542 2.01,2.354 false 2.104,2.76 2.417,2.917 0.313,0.156 10 false *a 2.396,2.771 2.708,2.927 0.313,0.156 10 false *b 2.667,2.75 2.979,2.906 0.313,0.156 10 false *c 2.969,2.771 3.281,2.927 0.313,0.156 10 false *d 0.198,3.177 0.51,3.333 0.313,0.156 10 false *e 0.958,0.448 1.271,0.604 0.313,0.156 10 false *f 2.75,0.677 3.063,0.833 0.313,0.156 10 false *g 2.625,3.813 2.938,3.969 0.313,0.156 10 false *h 0.344,0.438 0.656,0.594 0.313,0.156 10 false *i 2.438,0.396 2.75,0.552 0.313,0.156 10 false *j 0.375,2.458 0.688,2.615 0.313,0.156 10 false *k 0.344,1.948 0.656,2.104 0.313,0.156 10 false *l 0.344,1.75 0.656,1.906 0.313,0.156 10 false *m 0.302,1.271 0.615,1.427 0.313,0.156 10 false *n 1.802,2.552 2.115,2.708 0.313,0.156 10 false *o 2.271,1.927 2.583,2.083 0.313,0.156 10 false *p 1.823,1.875 2.135,2.031 0.313,0.156 10 false *q 2.281,1.24 2.594,1.396 0.313,0.156 10 false *r
*a 1500 mm (4.92 ft.)
*b 1700 mm (5.58 ft.)
*c 3000 mm (9.84 ft.)
*d 3200 mm (10.5 ft.)
*e String 1
*f String 2
*g String 3
*h String 4
*i String 5
*j String 6
*k Mark O
*l Mark P
*m Mark Q
*n Mark R
*o Mark S
*p Mark T
*q Mark U
*r Mark V


Make marks on string 5 that are 1500 mm (4.92 ft.), 1700 mm (5.58 ft.), 3000 mm (9.84 ft.), and 3200 mm (10.5 ft.) from the datum line (string 1) as shown in the illustration. (Marks O, P, Q and R)


xii.

Make marks on string 6 that are 1500 mm (4.92 ft.), 1700 mm (5.58 ft.), 3000 mm (9.84 ft.), and 3200 mm (10.5 ft.) from the datum line (string 1) as shown in the illustration. (Marks S, T, U and V)


xiii.

Place and secure the cross check markers, centered on marks H, I, M and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.



E287112C01
4.26,2.052 4.583,1.917 false 4.26,2.792 4.583,2.667 false 4.25,2.25 4.583,2.375 false 4.25,2.99 4.583,3.115 false 2.573,2.385 2.896,2.25 false 2.573,3.115 2.896,2.979 false 2.573,1.927 2.906,2.052 false 2.563,2.667 2.896,2.792 false 4.365,1.406 4.833,0.917 false 4.271,2.896 5.708,2.521 5.708,2.521 4.292,2.135 false 2.5,1.167 2.896,1.427 false 4.26,0.26 4.26,0.167 4.26,0.167 4.677,0.167 false 5.469,1.448 5.635,1.448 5.635,1.448 5.635,1.75 false 2.5,4.667 2.896,4.365 false 4.667,4.667 4.26,4.365 false 3.417,5.469 3.417,4.396 false 3.083,4.75 3.208,4.375 false 4.083,4.75 3.958,4.375 false 4.906,3.708 5.24,3.354 false 3.927,1.146 4.01,1.146 4.01,1.146 3.958,1.438 false 3.24,1.146 3.156,1.146 3.156,1.146 3.198,1.438 false 4.26,1.438 4.438,1.635 false 3.531,1.417 3.729,0.521 false 2.865,2.906 1.156,2.51 1.156,2.51 2.875,2.146 false 2.865,1.271 2.385,0.625 false 4.281,4.51 4.667,5.25 false 2.865,4.51 2.406,5.25 false 3.354,5.5 4.188,5.667 0.833,0.167 10 false *d 2.99,4.781 3.24,4.948 0.25,0.167 10 false *k 2.354,4.677 2.688,4.844 0.333,0.167 10 false *l 4.031,4.792 4.281,4.958 0.25,0.167 10 false *j 4.698,4.698 4.948,4.865 0.25,0.167 10 false *m 5.292,3.302 5.708,3.469 0.417,0.167 10 false *e 4.635,3.063 4.969,3.229 0.333,0.167 10 false *r 4.635,2.583 4.969,2.75 0.333,0.167 10 false *s 4.635,2.323 4.969,2.49 0.333,0.167 10 false *t 4.635,1.833 4.969,2 0.333,0.167 10 false *u 4.75,0.104 5.333,0.271 0.583,0.167 10 false *b 4.885,0.833 6.135,1 1.25,0.167 10 false *c 5.563,1.792 6.146,1.958 0.583,0.167 10 false *a 3.75,1.083 4.083,1.25 0.333,0.167 10 false *g 3.302,1.083 3.635,1.25 0.333,0.167 10 false *f 2.292,1.063 2.625,1.229 0.333,0.167 10 false *h 2.396,1.833 2.667,2.052 0.271,0.219 10 false *q 2.385,2.323 2.719,2.49 0.333,0.167 10 false *p 2.365,2.604 2.698,2.771 0.333,0.167 10 false *o 2.406,3.125 2.74,3.292 0.333,0.167 10 false *n 0.969,2.448 1.802,2.615 0.833,0.167 10 false *d 4.479,1.604 4.813,1.771 0.333,0.167 10 false *i 3.74,0.365 4.323,0.531 0.583,0.167 10 false *d 5.802,2.438 6.635,2.604 0.833,0.167 10 false *d 2.302,0.469 3.552,0.635 1.25,0.167 10 false *c 4.677,5.302 5.927,5.469 1.25,0.167 10 false *c 2.313,5.313 3.563,5.479 1.25,0.167 10 false *c
*a 100 mm (0.33 ft.) *b 800 mm (2.62 ft.)
*c Cross Check Marker *d Check Marker
*e String 1 *f Mark F
*g Mark G *h Mark H
*i Mark I *j Mark K
*k Mark L *l Mark M
*m Mark N *n Mark O
*o Mark P *p Mark Q
*q Mark R *r Mark S
*s Mark T *t Mark U
*u Mark V - -



xiv.

Place check markers between marks F and G, marks K and L, marks O and P, marks Q and R, marks S and T, and marks U and V.


xv.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 8: CAMERA VIEW ADJUSTMENT (CALIBRATION)


a.

Start diagnostic mode.


NOTICE:

The following must be carried out with the engine running. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.



b.
E366768

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E366769E01
0.146,0.104 1.375,0.302 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen to display the Mode Setting screen.


d.
E372764

Select "View Adjustment" on the Mode Setting screen to display the adjustment screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



e.
E393501

After checking the screen, press the "NEXT" button on the "Signal Check" screen.

HINT:
·

When "CHK" (red) is displayed, perform the inspections.

·

If performing the adjustment after proceeding to the next screen, check that all items display "OK" (blue) before selecting "Next".




f.

Perform the view adjustment.

E372766C01
1.406,0.406 1.615,0.406 1.615,0.406 2.073,0.625 true 3.198,0.146 2.979,0.146 2.979,0.146 2.844,0.615 true 2.656,0.135 2.51,0.135 2.51,0.135 2.375,0.604 true 4.708,0.177 4.49,0.177 4.49,0.177 4.427,0.365 true 5.833,0.719 5.615,0.719 5.615,0.719 5.302,1.083 true 5.01,2.583 4.792,2.583 4.792,2.583 4.354,1.875 true 3.208,2.635 2.99,2.635 2.99,2.635 2.854,2.156 true 2.635,2.604 2.417,2.604 2.417,2.604 2.417,2.167 true 1.615,2.635 1.771,2.635 1.771,2.635 2.083,2.156 true 1.354,1.75 2.802,1.75 2.802,1.75 2.875,1.917 true 2.719,1.75 2.802,1.927 true 2.031,1.75 2.115,1.927 true 1.969,1.75 2.052,1.927 true 1.323,1.219 2.771,1.219 2.771,1.219 2.844,1.385 true 1.323,0.781 2.771,0.781 2.771,0.781 2.844,0.948 true 2,1.219 2.073,1.375 true 2,0.781 2.073,0.948 true 1.135,0.688 1.448,0.885 0.313,0.198 10 false *a 1.156,1.135 1.469,1.333 0.313,0.198 10 false *a 1.167,1.667 1.479,1.865 0.313,0.198 10 false *a 2.688,2.521 3,2.719 0.313,0.198 10 false *a 2.688,0.042 3,0.24 0.313,0.198 10 false *a 1.219,0.313 1.531,0.51 0.313,0.198 10 false *b 1.448,2.552 1.76,2.75 0.313,0.198 10 false *b 3.24,0.063 3.552,0.26 0.313,0.198 10 false *b 3.25,2.552 3.563,2.75 0.313,0.198 10 false *b 5.083,2.51 5.396,2.708 0.313,0.198 10 false *c 4.75,0.104 5.063,0.302 0.313,0.198 10 false *d 5.875,0.625 6.188,0.823 0.313,0.198 10 false *e
*a Red Line *b Cross Check Marker
*c Adjustment Button *d Camera Select Button
*e Height Control Button - -


NOTICE:

If replacing a camera, select the repaired camera and press "New Camera".


i.

Check that the cross check markers displayed on the adjustment screen appear connected.

E271143

NOTICE:
·

Before checking the adjustment screen, ensure that the check markers have been placed correctly.

·

If a cross check marker appears displaced on the adjustment screen, use the camera select buttons to select the corresponding camera, and then use the adjustment buttons or vehicle height adjustment buttons to adjust the screen.

E372767E01
4.781,0.323 6.604,0.573 1.823,0.25 10 false After selecting the button 5.479,1.885 6.844,2.125 1.365,0.24 10 false button selected 0.865,2.01 2.667,2.26 1.802,0.25 10 false When selecting button 5.448,3.615 6.865,3.844 1.417,0.229 10 false button selected 5.469,5.427 6.604,5.625 1.135,0.198 10 false button selected 5.479,7.323 6.969,7.5 1.49,0.177 10 false button selected



HINT:

If adjustment is needed, select "All View Reset" button and reset all adjustment values.



ii.

Check the check marker is in the adjustment screen.

E271144

NOTICE:
·

Before checking the adjustment screen, ensure that the check markers have been placed correctly.

·

If a check marker appears displaced on the adjustment screen, use the camera select buttons to select the corresponding camera, and then use the adjustment buttons or vehicle height adjustment buttons to adjust the screen.

E372767E01
4.781,0.323 6.604,0.573 1.823,0.25 10 false After selecting the button 5.479,1.885 6.844,2.125 1.365,0.24 10 false button selected 0.865,2.01 2.667,2.26 1.802,0.25 10 false When selecting button 5.448,3.615 6.865,3.844 1.417,0.229 10 false button selected 5.469,5.427 6.604,5.625 1.135,0.198 10 false button selected 5.479,7.323 6.969,7.5 1.49,0.177 10 false button selected

HINT:

If performing adjustment again, select "All View Reset" to initialize the adjustment status.






g.
E372775

When all adjustments are completed, press "OK".


h.

If data writing ends normally, "The view data writing was completed." is displayed.


i.

Press "OK".




PROCEDURE 9: STEERING ANGLE SETTING


a.

Preparation for adjustment

i.

Park the vehicle with the steering wheel centered.

HINT:

Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.



ii.

Adjust the tire pressure to the specified value(s).



b.

Start diagnostic mode.


NOTICE:

The following must be carried out with the engine running. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.



c.
E366768

Select "Function Check/Setting" on the "Service Menu" screen.


d.
E366769E01
0.146,0.104 1.375,0.302 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.


e.
E372764

Select "Steering Angle Setting" on the Mode Setting screen to display the Signal Check screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



f.
E393501

Select "Next" on the Signal Check screen to display the Steering Angle Setting screen.

NOTICE:
·

If "CHK" (red) is displayed for an item on the Signal Check screen, selecting "Next" will not change to the Steering Angle Setting screen.

·

Check the Signal Check screen when "CHK" (red) is displayed for an item on the Signal Check screen.




g.

Adjust the steering angle

i.
E366773

Check that the steering wheel is centered (approximately +/- 5 degrees or less) and then select "Steering Center Memorize".


ii.

Turn the steering wheel fully to the left and fully to the right, and then press "Max Steering Angle Memorize". (Turning right and then left is OK)


iii.

When "Max Steering Angle Memorize" is selected, the system beeps, the steering angle setting values (steering neutral point and maximum steering angle) are stored, and the Mode Setting screen is displayed again.

HINT:
·

A beep will sound to confirm that the adjustment values have been stored.

·

If all signals are input normally, the Mode Setting screen is displayed automatically after the maximum steering angle is stored.

·

If steering angle setting is incomplete, "OK" cannot be selected.

·

Even if no DTC is detected, a steering sensor malfunction may disable the use of "Max Steering Angle Memorize".

·

If selecting "Max Steering Angle Memorize" does not cause the adjustment value to be stored after adjusting the steering angle, replace the steering sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL






i.

Check steering angle adjustment.

HINT:

If the steering angle has been adjusted, check the steering angle adjustment on the panoramic view monitor screen after finishing diagnosis mode.



j.

Check on the parking assist monitor screen that the estimated course line moves until the steering wheel is fully turned to either the left or right.

HINT:

If the estimated course line stops moving before the steering wheel is fully turned to either the left or right, the steering angle adjustment values have not been stored correctly. In this case, perform "Steering Center Memorize" and "Max Steering Angle Memorize" again.




PROCEDURE 10: BACK CAMERA POSITION SETTING


HINT:
·

Be sure to check for DTCs before performing this procedure.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



a.

Preparation for adjustment

i.

Park the vehicle with the steering wheel centered.


ii.
E366785C01
0.833,0.917 1,0.917 1,0.917 1.417,1.583 false 0.583,1.969 0.969,1.969 false 2.021,0.438 2.333,0.594 0.313,0.156 10 false *a 2.292,1.021 2.604,1.177 0.313,0.156 10 false *b 2.333,2.698 2.646,2.854 0.313,0.156 10 false *c 1.958,3.875 2.292,4.094 0.333,0.219 10 false *d 2.76,1.417 3.073,1.573 0.313,0.156 10 false *e 2.667,2.115 2.979,2.271 0.313,0.156 10 false A 0.448,1.896 0.76,2.052 0.313,0.156 10 false C 0.688,0.844 1,1 0.313,0.156 10 false B
*a Vehicle Center
*b Target Bar for Back Camera Position Setting
*c Vehicle End
*d Front
*e Target Bar Center Axis


Set a target bar behind the vehicle for optical axis adjustment of the rear television camera assembly (back camera position setting).

HINT:

Create a target bar for adjustment only when adjusting the optical axis of the rear television camera assembly.


Dimension:
Area Specification
A 1148 mm (3.765 ft.)
B 1995 to 2005 mm (6.544 to 6.576 ft.)
C 100 mm (3.94 in.)


HINT:
·

Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 100 mm (3.94 in.) and 1995 to 2005 mm (6.544 to 6.576 ft.), respectively.

·

Use a high contrast tape color (black tape on a light surface, white tape on a dark surface, etc.).

·

Do not use tape which has a pattern such as a stripe.

·

Make sure that there are no lines other than the target bar in the target area.

·

Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.

·

Check that the luggage compartment door is fully closed.





b.

Start diagnostic mode.


NOTICE:

The following must be carried out with the engine started. Apply the parking brake, depress the brake pedal, check that the shift lever is in P, and ensure that the vehicle is not moving.


i.
E366768

Select "Function Check/Setting" on the "Service Menu" screen.


ii.
E366769E01
0.146,0.104 1.375,0.302 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.


iii.
E372764

Select "Back Camera Setting" on the "Mode Setting" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



iv.
E393501

Select "Next" on the "Signal Check" screen.

HINT:
·

When "CHK" (red) is displayed for any items on the "Signal Check" screen, selecting "Next" will not change the screen to the "Back Camera Position Setting D (*)" screen.

·

When "CHK" (red) is displayed for any items on the "Signal Check" screen, perform inspections using the "Signal Check" screen.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DIAGNOSIS SYSTEM





c.
E366770C01
1.698,1.042 1.875,0.729 1.875,0.729 2.125,0.719 false 0.333,1.167 0.969,1.083 true 2.688,1.417 3.104,1.583 true 1.177,1.885 1.177,1.719 true 1.49,1.885 1.49,1.719 true 1.813,1.875 1.813,1.708 true 2.135,1.875 2.135,1.708 true 2.677,0.75 3.094,0.667 true 2.427,1.094 2.615,1.073 2.615,1.073 2.427,1.021 true 2.625,1.073 3.063,1.073 true 2.156,0.635 2.469,0.792 0.313,0.156 10 false *a 0.177,1.125 0.333,1.323 0.156,0.198 10 false A 3.125,0.99 3.281,1.188 0.156,0.198 10 false B 1.125,1.917 1.281,2.115 0.156,0.198 10 false C 1.448,1.917 1.604,2.115 0.156,0.198 10 false D 3.167,0.583 3.323,0.781 0.156,0.198 10 false G 2.104,1.906 2.26,2.104 0.156,0.198 10 false F 1.771,1.917 1.927,2.115 0.156,0.198 10 false E 3.167,1.531 3.323,1.729 0.156,0.198 10 false H
*a Target Bar for Back Camera Position Setting


Back Camera Position Setting (Both Ends of Target Bar)

HINT:
·

When the luggage compartment door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.

·

If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the luggage compartment door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the luggage compartment door has been closed).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE



i.

Perform vertical and horizontal position adjustment.

·

Move the circle (A) left, right, up and down by selecting the buttons (C), (D), (E) and (F) so that the left end of Target Bar for Back Camera Position Setting is positioned within the center of the circle (A) (center of the inner red circle).



ii.

Perform roll angle adjustment.

·

Rotate the bar (B) by selecting the buttons (G) or (H) so that the bar (B) becomes parallel to Target Bar for Back Camera Position Setting.



iii.

Select "Next" on the "Back Camera Position Setting D (*)" screen.



d.
E366780C01
1.177,1.854 1.177,1.688 true 1.531,1.865 1.531,1.698 true 1.865,1.854 1.865,1.688 true 2.219,1.865 2.219,1.698 true 2.438,1.042 2.833,0.667 2.833,0.667 3.083,0.667 true 1.458,0.906 1.625,0.906 1.625,0.906 1.74,1.063 true 3.115,0.563 3.427,0.719 0.313,0.156 10 false *a 1.323,0.833 1.542,1.031 0.219,0.198 10 false A 1.125,1.885 1.344,2.083 0.219,0.198 10 false B 1.49,1.896 1.708,2.094 0.219,0.198 10 false C 1.813,1.875 2.031,2.073 0.219,0.198 10 false D 2.188,1.875 2.406,2.073 0.219,0.198 10 false E
*a Target Bar for Back Camera Position Setting


Back Camera Position Setting (Upper Left Corner of Target Bar)

HINT:
·

When the luggage compartment door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.

·

If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the luggage compartment door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the luggage compartment door has been closed).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE



i.

Perform camera optical axis adjustment (high accuracy adjustment).

·

Move the adjustment mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the corner of the mark (A) with the upper left corner of the target bar.

Standard:

The outer corner of the mark (A) is aligned with the upper left corner of the target bar.


E366764C02
5.281,5.5 5.594,5.656 0.313,0.156 10 false *c 3.406,5.479 3.719,5.635 0.313,0.156 10 false *b 2.698,3.167 3.01,3.323 0.313,0.156 10 false *a 4.604,3.167 4.917,3.323 0.313,0.156 10 false *a 6.521,3.135 6.833,3.292 0.313,0.156 10 false *a 0.115,2.406 1.344,2.604 1.229,0.198 10 false Example:
*a Too Far Inside *b Inner Corner Contacting
*c Too Far Outside - -




ii.

Select "Next" on the "Back Camera Position Setting D (*) L_TOP" screen.



e.
E366781C01
2.698,0.885 2.969,0.635 2.969,0.635 3.156,0.635 true 1.219,0.76 1.385,0.76 1.385,0.76 1.698,1.052 true 1.167,1.854 1.167,1.688 true 1.531,1.865 1.531,1.698 true 1.875,1.865 1.875,1.698 true 2.219,1.875 2.219,1.708 true 1.063,0.688 1.198,0.917 0.135,0.229 10 false A 3.177,0.552 3.427,0.719 0.25,0.167 10 false *a 2.177,1.896 2.313,2.125 0.135,0.229 10 false E 1.833,1.906 1.969,2.135 0.135,0.229 10 false D 1.49,1.896 1.625,2.125 0.135,0.229 10 false C 1.125,1.885 1.26,2.115 0.135,0.229 10 false B
*a Target Bar for Back Camera Position Setting


Back Camera Position Setting (Lower Left Corner of Target Bar)

HINT:
·

When the luggage compartment door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.

·

If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the luggage compartment door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the luggage compartment door has been closed).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE



i.

Perform camera optical axis adjustment (high accuracy adjustment).

·

Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the lower left corner of the target bar.

Standard:

The outer corner of the mark (A) is aligned with the lower left corner of the target bar.


E366765C02
2.677,4.406 2.99,4.563 0.313,0.156 10 false *b 6.51,4.365 6.823,4.521 0.313,0.156 10 false *c 4.635,4.479 4.948,4.635 0.313,0.156 10 false *c 5.594,3.396 5.906,3.552 0.313,0.156 10 false *a 3.667,3.396 3.979,3.552 0.313,0.156 10 false *a 0.104,2.385 1.104,2.75 1,0.365 10 false Example:
*a Too Far Inside *b Inner Corner Contacting
*c Too Far Outside - -




ii.

Select "Next" on the "Back Camera Position Setting D (*) L_BTM" screen.



f.
E366782C01
1.167,1.875 1.167,1.708 true 1.51,1.865 1.51,1.698 true 1.854,1.865 1.854,1.698 true 2.219,1.865 2.219,1.698 true 2.323,0.833 2.156,0.833 2.156,0.833 1.708,1.083 true 0.75,1.021 0.583,0.729 0.583,0.729 0.333,0.729 true 0.177,0.646 0.49,0.802 0.313,0.156 10 false *a 2.385,0.771 2.698,0.927 0.313,0.156 10 false A 1.115,1.906 1.438,2.063 0.323,0.156 10 false B 1.479,1.896 1.792,2.052 0.313,0.156 10 false C 1.823,1.885 2.135,2.052 0.313,0.167 10 false D 2.188,1.896 2.5,2.052 0.313,0.156 10 false E
*a Target Bar for Back Camera Position Setting


Back Camera Position Setting (Upper Right Corner of Target Bar)

HINT:
·

When the luggage compartment door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.

·

If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the luggage compartment door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the luggage compartment door has been closed).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE



i.

Perform camera optical axis adjustment (high accuracy adjustment).

·

Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the upper right corner of the target bar.

Standard:

The outer corner of the mark (A) is aligned with the upper right corner of the target bar.


E366767C02
1.479,3.167 1.792,3.323 0.313,0.156 10 false *a 2.115,5.5 2.427,5.656 0.313,0.156 10 false *b 4.083,5.51 4.396,5.667 0.313,0.156 10 false *c 3.458,3.177 3.771,3.333 0.313,0.156 10 false *a 5.344,3.135 5.656,3.292 0.313,0.156 10 false *a 0.115,2.417 1.052,2.792 0.938,0.375 10 false Example:
*a Too Far Inside *b Inner Corner Contacting
*c Too Far Outside - -




ii.

Select "Next" on the "Back Camera Position Setting D (*) R_TOP" screen.



g.
E366783C01
1.719,1.063 2.146,0.802 2.146,0.802 2.229,0.802 true 0.333,0.656 0.583,0.656 0.583,0.656 0.771,0.896 true 1.177,1.854 1.177,1.677 true 1.521,1.844 1.521,1.677 true 1.865,1.865 1.865,1.698 true 2.208,1.865 2.208,1.698 true 1.146,1.885 1.458,2.042 0.313,0.156 10 false B 0.146,0.573 0.458,0.729 0.313,0.156 10 false *a 1.49,1.896 1.802,2.052 0.313,0.156 10 false C 1.823,1.906 2.135,2.063 0.313,0.156 10 false D 2.177,1.917 2.49,2.073 0.313,0.156 10 false E 2.281,0.719 2.594,0.875 0.313,0.156 10 false A
*a Target Bar for Back Camera Position Setting


Back Camera Position Setting (Lower Right Corner of Target Bar)

HINT:
·

When the luggage compartment door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.

·

If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the luggage compartment door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the luggage compartment door has been closed).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE



i.

Perform camera optical axis adjustment (high accuracy adjustment).

·

Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the lower right corner of the target bar.

Standard:

The outer corner of the mark (A) is aligned with the lower right corner of the target bar.


E366766C02
5.094,3.375 5.406,3.531 0.313,0.156 10 false *a 2.073,4.344 2.385,4.5 0.313,0.156 10 false *b 5.969,4.313 6.281,4.469 0.313,0.156 10 false *c 4.063,4.396 4.375,4.552 0.313,0.156 10 false *c 3.167,3.344 3.479,3.5 0.313,0.156 10 false *a 0.104,2.417 0.885,2.75 0.781,0.333 10 false Example:
*a Too Far Inside *b Inner Corner Contacting
*c Too Far Outside - -




ii.

Select "Next" on the "Back Camera Position Setting D (*) R_BTM" screen.



h.
E366771E01
1.875,1.063 2.333,0.75 2.333,0.75 2.5,0.75 false 2.542,0.688 2.729,0.927 0.188,0.24 10 false A

Back Verify Mode

i.

Check that (A) and the target adjustment bar are overlapping.

·

If the lines are not aligned, perform the "Steering Center Memorize" and "Max Steering Angle Memorize" operations.

·

If (A) and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the back camera position setting operation.



ii.

Select "OK" to return to the "Mode Setting" screen and complete the adjustment.

HINT:
·

The update is not completed until "OK" is selected.

·

When "OK" is selected, a beep will sound to confirm that the adjustment values have been stored.

·

The adjustment values are not stored until the beep has sounded.