Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM D

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  DIAGNOSIS SYSTEM  


PARKING ASSIST MONITOR DIAGNOSIS SYSTEM


a.

For panoramic view monitor system diagnosis, signals received by the television camera controller can be checked, and the panoramic view monitor system can be calibrated, adjusted and checked using the radio and display receiver assembly.

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION


HINT:

The displayed screens and items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (VIEW ADJUSTMENT)


E393502E01
2.76,0.927 4.25,1.229 1.49,0.302 2.823,0.99 6.031,1.188 3.208,0.198 10 false Start diagnostic mode


DIAGNOSIS SCREEN TRANSITION (STEERING ANGLE SETTING)


E393503E01
2.708,0.917 4.177,1.271 1.469,0.354 2.771,0.99 5.979,1.188 3.208,0.198 10 false Start diagnostic mode 6.344,4.906 6.656,5.104 0.313,0.198 10 false or


DIAGNOSIS SCREEN TRANSITION (BACK CAMERA SETTING)


E393504E01
2.698,0.906 4.188,1.25 1.49,0.344 2.75,0.979 5.958,1.177 3.208,0.198 10 false Start diagnostic mode 4.542,5.104 4.854,5.302 0.313,0.198 10 false or

E372772



SIGNAL CHECK (television camera controller input signal)


a.

Start diagnostic mode.


i.
E366768

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E366769E01
0.146,0.104 1.375,0.302 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.

HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the television camera controller was performed after television camera controller replacement.

Television Camera Controller Initialization Screen Transition
Not performed "Signal Check" screen
Performed "Mode Setting" screen



iii.
E372764

When the screen changes to the "Mode Setting" screen, select "View Adjustment" to display the "Signal Check" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.

Signal check

i.
E393501

On the "Signal Check" screen, it is possible to inspect the state of signals sent to the television camera controller and check the settings.

Item Inspection Detail Note
CAN Speed signal input When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.
CAMERA SW Panoramic view monitor switch signal input

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, check that all items display "OK" (blue) before selecting "Next".





c.

CAN inspection

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.



d.

CAMERA SW inspection

i.

Check that "OK" (blue) is displayed for "CAMERA SW" and select "OK".

HINT:

If "CHK" (red) remains displayed or the "CAMERA SW" inspection result is not normal, perform troubleshooting according to the Problem Symptoms Table ("CHK" message(s) are displayed on the "Signal Check" screen).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.






CAMERA DETECTION SETTING


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


a.

Start diagnostic mode.


i.
E366768

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E366769E01
0.146,0.104 1.375,0.302 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.



b.

Camera Detection Setting

i.
E372764

Select "Camera Detection Setting" on the "Mode Setting " screen.


ii.
E366791

Select ON or OFF on the "Camera Detection Setting" screen as necessary.

HINT:

After selecting ON or OFF, return to the "Mode Setting" screen by selecting "OK" or "Back".






CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION