Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

·

This DTC is stored if the television camera controller receives a signal via CAN communication from the steering sensor that indicates a power supply system problem.

·

This DTC is stored if the rear television camera assembly receives a signal via CAN communication from the steering sensor that indicates a power supply system problem.


Television Camera Controller
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor


Circumference Monitoring Camera Control Module

Rear Television Camera Assembly
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor


Rear Camera

WIRING DIAGRAM

E372789E01
5.073,1.906 6.979,2.198 1.906,0.292 10 false Television Camera Controller 4.854,4.219 7.073,4.563 2.219,0.344 10 false Rear Television Camera Assembly 3,1.917 3.323,2.115 0.323,0.198 10 false K71 3.031,2.104 4.115,2.354 1.083,0.25 10 false Steering Sensor 3.115,1.49 3.49,1.688 0.375,0.198 10 false ESS 3.115,0.958 3.49,1.156 0.375,0.198 10 false IG1 3.125,0.396 3.5,0.594 0.375,0.198 10 false BAT 1.896,0.531 2.979,0.781 1.083,0.25 10 false ECU-DCC NO. 1 1.938,1.063 3.021,1.313 1.083,0.25 10 false ECU-IG1 NO. 2 0.24,0.927 1.76,1.188 1.521,0.26 10 false from IG1-NO. 1 Relay 0.833,0.375 1.917,0.625 1.083,0.25 10 false from Battery 1.021,4.406 3.323,4.792 2.302,0.385 10 false : CAN Communication Line 2.938,0.24 3.177,0.469 0.24,0.229 10 false 4 2.948,0.802 3.188,1.031 0.24,0.229 10 false 9 2.938,1.344 3.177,1.573 0.24,0.229 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

Since the panoramic view monitor system has functions that use the CAN communication system, first check that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE)
a.

Disconnect the K71 steering sensor connector.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K71-6 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K71-9 (IG1) - K71-6 (ESS) Engine switch on (IG) 11 to 14 V
K71-4 (BAT) - K71-6 (ESS) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR