Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  


DESCRIPTION

This DTC is stored if the rear television camera assembly judges as a result of its self check that the signals or signal lines between the rear television camera assembly and television camera controller are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C1621 Back Camera Power Supply Failure Rear television camera assembly power supply failure
·

Harness or connector

·

Rear television camera assembly


Rear Camera

WIRING DIAGRAM

E366794E03
4.865,2.521 7.135,2.771 2.271,0.25 10 false Rear Television Camera Assembly 0.396,2.542 2.771,2.844 2.375,0.302 10 false Television Camera Controller 1.427,1.146 1.677,1.354 0.25,0.208 10 false 1 1.427,1.542 1.677,1.75 0.25,0.208 10 false 2 1.427,1.906 1.677,2.115 0.25,0.208 10 false 9 5.479,1.156 5.729,1.365 0.25,0.208 10 false 3 5.469,0.427 5.719,0.635 0.25,0.208 10 false 6 5.521,1.521 5.771,1.729 0.25,0.208 10 false 2 5.51,1.896 5.76,2.104 0.25,0.208 10 false 5 0.927,2.01 1.417,2.24 0.49,0.229 10 false CGND 1.094,1.635 1.583,1.865 0.49,0.229 10 false CV- 1.063,1.26 1.552,1.49 0.49,0.229 10 false CV+ 0.302,0.49 1.5,0.708 1.198,0.219 10 false from ACC Relay 3.219,0.677 4.417,0.896 1.198,0.219 10 false ECU-ACC 4.865,2.365 6.104,2.594 1.24,0.229 10 false m4 5.698,0.51 6.094,0.719 0.396,0.208 10 false CB+ 5.708,1.26 6.104,1.469 0.396,0.208 10 false CV+ 5.698,1.615 6.094,1.823 0.396,0.208 10 false CV- 5.708,2.01 6.198,2.24 0.49,0.229 10 false CGND 3.427,3.385 5.698,3.635 2.271,0.25 10 false *: Shielded 3.469,1.823 4.198,2.083 0.729,0.26 10 false * 0.396,2.375 0.885,2.604 0.49,0.229 10 false R124

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the R124 television camera controller connector.


b.

Disconnect the m4 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R124-9 (CGND) - m4-5 (CGND) Always Below 1 Ω
R124-9 (CGND) or m4-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ACC POWER SUPPLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ACC POWER SUPPLY - BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
m4-6 (CB+) - Body ground Engine switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR