Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO ANTENNA CORD › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0318992 RADIO ANTENNA CORD A

AUDIO / VIDEO  RADIO ANTENNA CORD  INSTALLATION  


PROCEDURE

Hide 86101Q 1.INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY (w/ Digital Audio Broadcasting Antenna)

a.

Engage the 9 clamps to install the No. 4 antenna cord sub-assembly.


b.

Connect the connector.


Hide 86101J 2.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

HINT:

Butyl tape and adhesive tape are not available as supply parts. If these pieces of tape still have enough adhesion to secure the No. 2 antenna cord sub-assembly to the roof headlining assembly, reuse them. If the adhesive tape and/or the butyl tape is no longer sticky, apply new tape following the procedure below.


a.

Apply new butyl tape.

for Normal Roof:

E393384C01
0.583,0.167 6.583,8.75 6,8.583 1.25,3.167 5.917,8.667 4.667,5.5 3.719,1.219 3.719,0.938 false 3.719,4.073 3.719,3.792 false 3.719,6.979 3.719,6.698 false 0.583,2.917 6.583,2.917 false 1.25,5.917 5.917,5.917 false 0.698,0.281 1.052,0.542 0.354,0.26 12 false *A 0.708,3.031 1.083,3.323 0.375,0.292 12 false *B 1.333,3.25 1.688,3.552 0.354,0.302 12 false *C 1.344,6 1.667,6.281 0.323,0.281 12 false *D 3.635,1.219 3.802,1.396 0.167,0.177 10 true *a 3.635,4.073 3.802,4.25 0.167,0.177 10 true *a 3.635,6.969 3.802,7.146 0.167,0.177 10 true *a
*A for Radio Receiver Type *B for Radio and Display Type
*C w/o Television Antenna *D w/ Television Antenna
*a Marking - -
V100144

Butyl tape - -


for Moon Roof:

E378318C02
4.01,1.302 4.01,0.802 false 3.927,1.271 4.135,1.51 0.208,0.24 10 true *a
*a Marking - -
V100144

Butyl tape - -


for Panoramic Moon Roof:

E387992C01
3.823,1.365 3.823,0.865 false 3.75,5.365 3.75,4.865 false 0.75,0.427 1.104,0.688 0.354,0.26 12 false *A 0.76,4.417 1.115,4.708 0.354,0.292 12 false *B 3.74,1.365 4.052,1.521 0.313,0.156 10 false *a 3.667,5.354 3.979,5.51 0.313,0.156 10 false *a
*A w/o Television Antenna *B w/ Television Antenna
*a Marking - -
V100144

Butyl tape - -


i.

Remove the old butyl tape from the roof headlining assembly.


ii.

Prepare an appropriate amount of new butyl tape.

HINT:

Be careful not to touch the adhesive surface.



iii.

Apply the butyl tape to the roof headlining assembly while aligning the tape with the markings on the roof headlining assembly.


iv.

Peel off the release paper from the butyl tape.



b.

w/o Television Antenna:

i.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.

for Normal Roof:

E393385C01
0.427,2.302 0.583,2.031 true 0.427,6.115 0.583,5.844 true 6.198,4.906 6.625,4.833 true 6.198,1.115 6.625,1.042 true 6.375,7.406 6.688,7.125 true 0.271,2.219 0.438,2.042 false 6.396,0.771 6.625,0.896 false 6.396,4.573 6.625,4.698 false 0.281,6.031 0.448,5.854 false 6.625,7.427 6.729,7.25 false 0.469,0.302 0.823,0.615 0.354,0.313 12 false *A 0.469,4.104 0.854,4.396 0.385,0.292 12 false *B 0.333,2.281 0.646,2.438 0.313,0.156 10 false *a 6.229,7.354 6.542,7.51 0.313,0.156 10 false *c 0.167,2.219 0.479,2.417 0.313,0.198 10 false *d 0.333,6.094 0.646,6.25 0.313,0.156 10 false *a 5.99,4.833 6.198,5.031 0.208,0.198 10 true *b 6,1.042 6.208,1.24 0.208,0.198 10 true *b 6.24,0.688 6.552,0.885 0.313,0.198 10 false *d 6.24,4.49 6.552,4.688 0.313,0.198 10 false *d 0.167,6.031 0.479,6.229 0.313,0.198 10 false *d 6.542,7.427 6.854,7.625 0.313,0.198 10 false *d
*A for Radio Receiver Type *B for Radio and Display Type
*a Marking Tape (A) *b Marking Tape (B)
*c Marking Tape (C) *d Protrusion
V100155

Adhesive Tape
V113146

Adjustment Area


for Moon Roof:

E378315C03
0.406,2.177 0.552,1.823 true 6.729,3.406 6.781,3.198 false 6.448,0.51 6.688,0.677 false 6.26,0.865 6.677,0.813 true 6.458,3.302 6.74,3.063 true 0.229,2.052 0.406,1.844 false 0.313,2.146 0.625,2.302 0.313,0.156 10 false *a 6.063,0.781 6.26,0.969 0.198,0.188 10 true *b 6.333,3.26 6.646,3.417 0.313,0.156 10 false *c 0.125,2.052 0.438,2.208 0.313,0.156 10 false *d 6.292,0.427 6.604,0.583 0.313,0.156 10 false *d 6.625,3.406 6.938,3.563 0.313,0.156 10 false *d 0.188,0.177 0.563,0.417 0.375,0.24 12 false *A
*A for Radio and Display Type - -
*a Marking Tape (A) *b Marking Tape (B)
*c Marking Tape (C) *d Protrusion
V100155

Adhesive Tape
V113146

Adjustment Area


for Panoramic Moon Roof:

E378316C05
0.469,2.01 0.583,1.688 true 0.271,1.885 0.438,1.698 false 6.344,0.406 6.635,0.594 false 6.635,3.281 6.708,3.063 false 6.219,0.771 6.625,0.729 true 6.375,3.198 6.667,2.917 true 0.375,2 0.688,2.156 0.313,0.156 10 false *a 6.052,0.688 6.25,0.906 0.198,0.219 10 true *b 6.25,3.167 6.51,3.365 0.26,0.198 10 false *c 0.167,1.885 0.479,2.042 0.313,0.156 10 false *d 6.188,0.323 6.5,0.479 0.313,0.156 10 false *d 6.542,3.271 6.854,3.427 0.313,0.156 10 false *d 0.188,0.177 0.563,0.417 0.375,0.24 12 false *A
*A for Radio and Display Type - -
*a Marking Tape (A) *b Marking Tape (B)
*c Marking Tape (C) *d Protrusion
V100155

Adhesive Tape
V113146

Adjustment Area



ii.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the protrusion on the rear of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.


iii.

for Radio and Display Type:

1.

Align the marking tape (C) on the No. 2 antenna cord sub-assembly with the protrusion on the rear of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.



iv.

Install the No. 2 antenna cord sub-assembly to the roof headlining assembly.

NOTICE:
·

Make sure that there are no gaps between the roof headlining assembly and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord sub-assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.



HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area.



v.

Apply the adhesive tape as shown in the illustration to secure the No. 2 antenna cord sub-assembly.



c.

w/ Television Antenna:

i.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.

E371181C02
1.198,3.229 0.865,3.135 true 0.229,1.917 0.375,1.708 false 0.406,2.01 0.51,1.729 true 6.458,0.375 6.688,0.531 false 6.24,0.615 6.635,0.677 true 6.521,3.25 6.719,3.021 true 6.771,3.354 6.792,3.146 false 6.24,4.531 6.635,4.583 true 6.448,4.281 6.688,4.448 false 0.417,5.854 0.51,5.615 true 0.229,5.771 0.375,5.594 false 6.531,7.417 6.719,7.198 true 6.771,7.542 6.792,7.323 false 0.823,6.875 1.094,6.781 true 0.271,3.177 0.708,3.031 true 0.26,6.938 0.563,6.938 true 0.167,0.167 0.542,0.406 0.375,0.24 12 false *A 0.167,4.083 0.542,4.323 0.375,0.24 12 false *B 0.323,2.031 0.635,2.229 0.313,0.198 10 false *a 0.125,1.938 0.438,2.135 0.313,0.198 10 false *e 6.021,0.542 6.229,0.719 0.208,0.177 10 true *b 6.281,0.271 6.594,0.469 0.313,0.198 10 false *e 6.698,3.375 7.01,3.573 0.313,0.198 10 false *e 6.417,3.271 6.729,3.469 0.313,0.198 10 false *c 0.125,5.792 0.438,5.99 0.313,0.198 10 false *e 6.271,4.188 6.583,4.385 0.313,0.198 10 false *e 0.323,5.875 0.635,6.073 0.313,0.198 10 false *a 6.031,4.448 6.229,4.615 0.198,0.167 10 true *b 6.406,7.438 6.719,7.635 0.313,0.198 10 false *c 6.698,7.563 7.01,7.76 0.313,0.198 10 false *e 1.229,3.167 1.49,3.375 0.26,0.208 10 false *f 1.125,6.698 1.333,6.865 0.208,0.167 10 true *f 0.094,3.115 0.406,3.313 0.313,0.198 10 false *d 0.073,6.865 0.385,7.063 0.313,0.198 10 false *d
*A for Normal Roof *B for Panoramic Moon Roof
*a Marking Tape (A) *b Marking Tape (B)
*c Marking Tape (C) *d Marking Tape (D)
*e Protrusion *f Marking
V100155

Adhesive Tape
V113146

Adjustment Area



ii.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the protrusion on the rear of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.


iii.

Align the marking tape (C) on the No. 2 antenna cord sub-assembly with the protrusion on the rear of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.


iv.

Align the marking tape (D) on the No. 2 antenna cord sub-assembly with the marking on the roof headlining assembly and secure the No. 2 antenna cord sub-assembly with the adhesive tape as shown in the illustration.


v.

Install the No. 2 antenna cord sub-assembly to the roof headlining assembly.

NOTICE:
·

Make sure that there are no gaps between the roof headlining assembly and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord sub-assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.



HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area.



vi.

Apply the adhesive tape as shown in the illustration to secure the No. 2 antenna cord sub-assembly.



Hide 3.INSTALL ROOF HEADLINING ASSEMBLY

Hide 86101 4.INSTALL ANTENNA CORD SUB-ASSEMBLY (for LHD)

a.

w/o Telematics Transceiver:

i.

Engage the 6 clamps to install the antenna cord sub-assembly.



b.

w/ Telematics Transceiver:

i.

Engage the 6 clamps to install the antenna cord sub-assembly.


ii.

Connect the connector.



Hide 55086 5.INSTALL NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for LHD)

Hide 55972C 6.INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT (for LHD)

Hide 86101 7.INSTALL ANTENNA CORD SUB-ASSEMBLY (for RHD)

a.

Engage the 6 clamps to install the antenna cord sub-assembly.


Hide 55084E 8.INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REASSEMBLY


Hide 83108 9.INSTALL METER MIRROR SUB-ASSEMBLY (for RHD)

w/ Headup Display:

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY>INSTALLATION


Hide 55950G 10.INSTALL DEFROSTER NOZZLE ASSEMBLY (for RHD)

w/ Headup Display:

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REASSEMBLY


Hide 55972C 11.INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT (for RHD)

w/ Headup Display:

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REASSEMBLY


Hide 55971C 12.INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REASSEMBLY


Hide 13.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY