1.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
When installing a new instrument panel safety pad sub-assembly:
Immediately before installing the instrument panel safety pad sub-assembly, twist and cut off the portion as shown in the illustration.
Engage the 4 guides to temporarily install the instrument panel safety pad sub-assembly as shown in the illustration.
|
Install in this Direction | - | - |
Do not damage the instrument panel safety pad sub-assembly.
Do not allow the wire harnesses to interfere with the surrounding parts.
Install the instrument panel safety pad sub-assembly with the 4 bolts <B>, 2 bolts <A> and nut <F>.
| *a | Bolt <A> | *b | Bolt <B> |
| *c | Clip | *d | Nut <F> |
Install the 2 clips.
Engage each clamp.
| *A | w/ Digital Audio Broadcasting Antenna, Television Antenna or Telematics Transceiver | *B | w/ Ion Generator |
| *C | w/ Headup Display | *D | w/ Telematics Transceiver |
Connect each connector.
for Automatic Air Conditioning System:
|
Install in this Direction |
Engage the 2 claws to connect the cooler (room temp. sensor) thermistor as shown in the illustration.
82149A
2.CONNECT NO. 5 INSTRUMENT PANEL WIRE (w/o Occupant Classification System)
82149A
3.CONNECT NO. 5 INSTRUMENT PANEL WIRE (w/ Occupant Classification System)
55650
4.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
|
Install in this Direction |
Engage the 2 clips and 2 claws to install the No. 1 instrument panel register assembly as shown in the illustration.
55011A
5.INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
|
Install in this Direction |
Engage the 4 clips to install the No. 1 instrument panel garnish sub-assembly as shown in the illustration.
86160P
6.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
Use the same procedure as for the LH side.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSTALLATION
55473B
7.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL
|
Install in this Direction |
Engage the 2 guides as shown in the illustration.
|
Install in this Direction |
Engage the 2 clips to install the No. 2 instrument panel speaker panel as shown in the illustration.
86160P
8.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
55472C
9.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL
|
Install in this Direction |
Engage the 2 guides as shown in the illustration.
|
Install in this Direction |
Engage the 2 clips to install the No. 1 instrument panel speaker panel as shown in the illustration.
55303B
10.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Passenger Side Knee Airbag)
Connect the connector.
|
Install in this Direction |
Engage the 4 claws as shown in the illustration.
Install the 2 bolts <D>.
Install the lower instrument panel sub-assembly with the 3 screws <C>.
55303B
11.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/ Passenger Side Knee Airbag)
Connect the connector.
|
Install in this Direction |
Engage the 4 claws as shown in the illustration.
Install the lower instrument panel sub-assembly with the 5 screws <C>.
73990
12.INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)
55607
13.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Connect the connector.
Engage the clamp.
|
Install in this Direction |
Engage the 2 guides as shown in the illustration.
|
Install in this Direction |
Engage the 4 claws to install the No. 2 instrument panel under cover sub-assembly as shown in the illustration.
55317A
14.INSTALL INSTRUMENT SIDE PANEL RH
|
Install in this Direction |
Engage the 3 guides as shown in the illustration.
|
Install in this Direction |
Engage the 4 clips and 2 claws to install the instrument side panel RH as shown in the illustration.
62211
15.INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
62211
16.INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
62311B
17.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
62111A
18.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
67913
19.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
20.INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)
Connect the connector.
Install the radio tuner opening cover with bracket with the 4 bolts <B>.
55420A
21.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Radio Receiver)
Connect the connector.
Engage the 5 clips as shown in the illustration.
|
Install in this Direction | - | - |
Engage the 4 clips in the order shown in the illustration to install the center instrument cluster finish panel assembly.
|
Install in this Direction | - | - |
55423B
22.INSTALL INSTRUMENT CLUSTER FINISH PANEL COVER (w/o Radio Receiver)
for RHD:
|
Install in this Direction |
Engage the 4 clips to install the instrument cluster finish panel cover as shown in the illustration.
23.INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)
24.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
for 7 Inch Display:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>INSTALLATION
25.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
for 8 Inch Display:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>INSTALLATION
55900
26.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (except 8 Inch Display)
55670
27.INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
Connect the connector.
Engage the 11 clips to install the No. 3 instrument panel register assembly as shown in the illustration.
|
Install in this Direction | - | - |
55480D
28.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
w/ Switch:
Connect the connector.
|
Install in this Direction |
Engage the 5 clips to install the lower instrument panel finish panel assembly as shown in the illustration.
83100
29.INSTALL COMBINATION METER ASSEMBLY
55410C
30.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Connect the connector.
|
Install in this Direction |
Engage the 2 guides and 4 clips to install the instrument cluster finish panel assembly as shown in the illustration.
Install the 2 clips.
73900
31.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)
55302D
32.INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)
Connect each connector.
Engage the clamp.
|
Install in this Direction |
Engage the 8 clips to install the No. 1 instrument panel sub-assembly as shown in the illustration.
55302D
33.INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (w/ Driver Side Knee Airbag)
Connect each connector.
Engage the clamp.
|
Install in this Direction |
Engage the 6 clips to install the No. 1 instrument panel sub-assembly as shown in the illustration.
53601
34.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
55436B
35.INSTALL NO. 2 METER HOOD CLUSTER
|
Install in this Direction |
Engage the 3 clips to install the No. 2 meter hood cluster as shown in the illustration.
55606
36.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
Engage the 2 claws to connect the DLC3 connector.
Engage the 2 clamps.
Connect the connector.
|
Install in this Direction |
Engage the guide as shown in the illustration.
|
Install in this Direction |
Engage the 3 claws as shown in the illustration.
Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <C>.
55606
37.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
Engage the 2 claws to connect the DLC3 connector.
Engage the clamp.
Connect the connector.
|
Install in this Direction |
Engage the 2 claws as shown in the illustration.
Install the No. 1 instrument panel under cover sub-assembly with the 3 screws <C>.
55318C
38.INSTALL INSTRUMENT SIDE PANEL LH
|
Install in this Direction |
Engage the 3 guides as shown in the illustration.
|
Install in this Direction |
Engage the 4 clips and 2 claws to install the instrument side panel LH as shown in the illustration.
62212
39.INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)
62212
40.INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)
62312B
41.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62112A
42.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
67914
43.INSTALL FRONT DOOR SCUFF PLATE LH
58810J
44.INSTALL CONSOLE BOX ASSEMBLY
84329
45.INSTALL TURN SIGNAL SWITCH
84650
46.INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY
45286B
47.INSTALL UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)
45286B
48.INSTALL UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)
45024
49.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)
45024
50.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)
51.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
84306
52.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
53.INSTALL STEERING WHEEL ASSEMBLY
54.CHECK STEERING WHEEL CENTER POINT
45130
55.INSTALL HORN BUTTON ASSEMBLY
56. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (for Power Tilt and Power Telescopic Steering Column)