Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM C

6AR-FSE ENGINE CONTROL  SFI SYSTEM  P019011  Fuel Rail Pressure Sensor "A" Circuit Short to Ground  


DESCRIPTION

A107720E07
0.063,0.458 1.333,0.75 1.271,0.292 10 false Output Voltage (V) 0.344,1.031 0.573,1.24 0.229,0.208 10 false 4.5 0.333,2.156 0.563,2.365 0.229,0.208 10 false 0.5 0.74,2.417 0.854,2.625 0.115,0.208 10 false 0 2.458,2.417 2.865,2.688 0.406,0.271 10 false 30.0 0.917,2.698 2.333,2.938 1.417,0.24 10 false Fuel Pressure (MPa)

The fuel pressure sensor is installed on the fuel delivery pipe sub-assembly for high pressure side. The fuel pressure sensor changes the fuel pressure for high pressure side into an electrical signal and sends the signal to the ECM. Then the ECM controls the pump discharge using this feedback to maintain the fuel's target pressure between2.0 and 25 MPa (20 and 255 kgf/cm2, 290 and 3625 psi).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P019011 Fuel Rail Pressure Sensor "A" Circuit Short to Ground The fuel pressure sensor output voltage is less than 0.293 V for 3 seconds or more (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor

·

ECM


Comes on DTC stored SAE Code:
P0192

HINT:

When this DTC is output, check the fuel pressure sensor in the Data List. Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).

DTC No. Fuel Pressure (High) Malfunction
P019011 Approximately 0 kPa
·

Short to ground in PR circuit

·

Short in PR to EPR circuit

·

Open in VCPR circuit



If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


MONITOR DESCRIPTION

This DTC is stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short in the sensor circuit.

Example:

If the fuel pressure sensor output voltage is less than 0.293 V for 3 seconds or more, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components Fuel pressure sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Start the engine.

7.

Idle the engine for 10 seconds.

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P019011.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A403505E15
0.5,2.885 0.958,3.083 0.458,0.198 10 false F22 0.5,3.052 3.01,3.573 2.51,0.521 10 false Fuel Pressure Sensor 1.406,1.021 1.719,1.219 0.313,0.198 10 false VC 1.729,0.906 1.885,1.104 0.156,0.198 10 false 1 1.333,1.719 1.792,1.917 0.458,0.198 10 false PR 1.729,1.604 1.885,1.802 0.156,0.198 10 false 3 1.417,2.49 1.729,2.688 0.313,0.198 10 false E2 1.74,2.385 1.896,2.583 0.156,0.198 10 false 2 4.281,0.927 4.594,1.125 0.313,0.198 10 false 136 4.281,1.594 4.74,1.792 0.458,0.198 10 false 103 4.281,2.385 4.594,2.583 0.313,0.198 10 false 135 4.604,0.917 5.167,1.208 0.563,0.292 10 false VCPR 4.604,1.604 5.063,1.802 0.458,0.198 10 false PR 4.615,2.385 5.229,2.583 0.615,0.198 10 false EPR 5.615,0.688 6.073,0.885 0.458,0.198 10 false 5 V 4.938,3.115 5.396,3.313 0.458,0.198 10 false C58 5.292,3.115 5.719,3.396 0.427,0.281 10 false ECM 5.281,1.406 5.896,1.604 0.615,0.198 10 false 180 kΩ

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A403507C11
0.5,1.083 0.917,1.333 0.417,0.25 1.094,1.719 1.51,1.302 true 2.229,1.729 1.938,1.292 true 1.74,1.76 1.729,1.313 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 0.583,1.115 0.896,1.354 0.313,0.24 10 false F22 0.938,1.75 1.25,1.948 0.313,0.198 10 false VC 1.656,1.792 1.969,1.99 0.313,0.198 10 false E2 2.177,1.781 2.49,1.979 0.313,0.198 10 false PR
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the fuel pressure sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F22-1 (VC) - F22-2 (E2) Engine switch on (IG) 4.75 to 5.25 V
F22-3 (PR) - F22-2 (E2) Engine switch on (IG) 3.0 to 5.25 V



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F22-1 (VC) - F22-3 (PR) Engine switch off 171 to 189 kΩ



HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F22-1 (VC) - C58-136 (VCPR) Always Below 1 Ω
F22-3 (PR) or C58-103 (PR) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR