Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM C

6AR-FSE ENGINE CONTROL  SFI SYSTEM  P040314  Exhaust Gas Recirculation "A" Control Circuit 1 Open  P140000  Exhaust Gas Recirculation "A" Control Circuit 2 Open  P140596  Exhaust Gas Recirculation "A" Control Circuit 3 Open  P141004  Exhaust Gas Recirculation "A" Control Circuit 4 Open  


DESCRIPTION

Refer to DTC P04019C.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>P04019C

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P040314 Exhaust Gas Recirculation "A" Control Circuit 1 Open Open or short in EGR1 circuit for 1 second or more (1 trip detection logic).
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored SAE Code:
P0403
P140000 Exhaust Gas Recirculation "A" Control Circuit 2 Open Open or short in EGR2 circuit for 1 second or more (1 trip detection logic).
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored SAE Code:
P0403
P140596 Exhaust Gas Recirculation "A" Control Circuit 3 Open Open or short in EGR3 circuit for 1 second or more (1 trip detection logic).
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored SAE Code:
P0403
P141004 Exhaust Gas Recirculation "A" Control Circuit 4 Open Open or short in EGR4 circuit for 1 second or more (1 trip detection logic).
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored SAE Code:
P0403

MONITOR DESCRIPTION

These DTCs are stored if an open or short in the EGR valve assembly circuit is detected.

Example:

·

If the EGR1, EGR2, EGR3 or EGR4 operation signal is off, but the step motor output signal is on, the ECM determines that there is a short in the EGR valve assembly circuit, and stores a DTC.

·

If the EGR1, EGR2, EGR3 or EGR4 operation signal is on, and the step motor output signal is off, the ECM determines that there is an open or short in the EGR valve assembly circuit, and stores a DTC.


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A215251E49
2.333,2.896 2.917,3.302 0.583,0.406 10 false Warming up 3.146,2.906 4.479,3.104 1.333,0.198 10 false 10 minutes or more 2.021,2.083 2.344,2.323 0.323,0.24 10 false [A] 2.531,1.781 2.792,2.063 0.26,0.281 10 false [B] 3.781,0.688 4.156,1.115 0.375,0.427 10 false [C] 4.438,3.292 4.75,3.604 0.313,0.313 10 false [D] 0.74,0.813 1.792,0.99 1.052,0.177 10 false 20 km/h or more 1.438,1.906 1.813,2.083 0.375,0.177 10 false Idling 0.896,2.229 1.813,2.635 0.917,0.406 10 false Engine Switch on (IG) 0.865,0.271 1.917,0.448 1.052,0.177 10 false Vehicle Speed 5.615,2.656 6.302,2.948 0.688,0.292 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG) [A].

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

9.

Drive the vehicle at 20 km/h (12 mph) or more for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P040314, P140000, P140596 or P141004.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [B] through [D] again.




WIRING DIAGRAM

A414845E02
5.74,2.885 6.125,3.094 0.385,0.208 10 false C58 5.771,1.208 6.156,1.417 0.385,0.208 10 false A78 5.802,1.01 6.188,1.219 0.385,0.208 10 false 46 5.771,2.688 6.156,2.896 0.385,0.208 10 false 36 5.771,3.104 6.156,3.313 0.385,0.208 10 false 33 5.781,3.49 6.167,3.698 0.385,0.208 10 false 37 5.771,3.885 6.156,4.094 0.385,0.208 10 false 32 6.375,4.719 6.76,4.927 0.385,0.208 10 false ECM 6.125,1.208 6.594,1.438 0.469,0.229 10 false MREL 6.125,2.885 6.604,3.104 0.479,0.219 10 false EGR1 3.323,2.792 3.708,3 0.385,0.208 10 false 4 3.323,3.177 3.708,3.385 0.385,0.208 10 false 3 3.323,3.563 3.708,3.771 0.385,0.208 10 false 6 3.313,3.948 3.698,4.156 0.385,0.208 10 false 1 3.323,4.344 3.708,4.552 0.385,0.208 10 false 2 3.333,4.719 3.719,4.927 0.385,0.208 10 false 5 1.875,5.188 2.354,5.427 0.479,0.24 10 false C109 1.885,5.354 3.406,5.594 1.521,0.24 10 false EGR Valve Assembly 2.969,4.344 3.354,4.552 0.385,0.208 10 false +B1 0.385,2.5 1.458,2.771 1.073,0.271 10 false EFI-MAIN NO. 1 0.406,3.177 1.031,3.385 0.625,0.208 10 false FL MAIN 0.573,3.979 1.094,4.219 0.521,0.24 10 false Battery 1.979,1.583 3.052,1.854 1.073,0.271 10 false EFI-MAIN NO. 1 5.75,3.292 6.135,3.5 0.385,0.208 10 false C58 5.75,3.677 6.135,3.885 0.385,0.208 10 false C58 5.74,4.073 6.125,4.281 0.385,0.208 10 false C58 6.125,3.281 6.604,3.5 0.479,0.219 10 false EGR2 6.125,3.698 6.604,3.917 0.479,0.219 10 false EGR3 6.125,4.063 6.604,4.281 0.479,0.219 10 false EGR4 2.844,2.792 3.323,3.01 0.479,0.219 10 false EGR1 2.844,3.188 3.323,3.406 0.479,0.219 10 false EGR2 2.865,3.563 3.344,3.781 0.479,0.219 10 false EGR3 2.854,3.958 3.333,4.177 0.479,0.219 10 false EGR4 2.958,4.719 3.344,4.927 0.385,0.208 10 false +B2 2,1.104 2.385,1.313 0.385,0.208 10 false 1 2.01,0.531 2.396,0.74 0.385,0.208 10 false 3 2.823,0.531 3.208,0.74 0.385,0.208 10 false 5 2.813,1.094 3.198,1.302 0.385,0.208 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



e.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Engine Speed, Intake Manifold Absolute Pressure and Coolant Temperature.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50004 372 25 211,385,205

f.

Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stalls
Intake Manifold Absolute Pressure
(Data List)
Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs)
(2.9 to 5.8 psi(abs))
(EGR valve is fully closed)
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:

During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT EGR VALVE ASSEMBLY
2.INSPECT EGR VALVE ASSEMBLY
a.

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)
A376490C14
0.333,1 0.75,1.25 0.417,0.25 1.781,1 2.323,0.646 true 2.469,1.885 1.781,1.375 true 0.208,0.146 0.521,0.344 0.313,0.198 10 false *a 0.385,1.042 0.844,1.24 0.458,0.198 10 false C109 2.385,0.531 2.844,0.729 0.458,0.198 10 false +B1 2.552,1.854 3.01,2.052 0.458,0.198 10 false +B2
*a Front view of wire harness connector (to EGR Valve Assembly)


a.

Disconnect the EGR valve assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C109-2 (+B1) - Body ground Engine switch on (IG) 11 to 14 V
C109-5 (+B2) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - EGR VALVE ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)
a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C109-4 (EGR1) - C58-36 (EGR1) Always Below 1 Ω
C109-3 (EGR2) - C58-33 (EGR2) Always Below 1 Ω
C109-6 (EGR3) - C58-37 (EGR3) Always Below 1 Ω
C109-1 (EGR4) - C58-32 (EGR4) Always Below 1 Ω
C109-4 (EGR1) or C58-36 (EGR1) - Body ground and other terminals Always 10 kΩ or higher
C109-3 (EGR2) or C58-33 (EGR2) - Body ground and other terminals Always 10 kΩ or higher
C109-6 (EGR3) or C58-37 (EGR3) - Body ground and other terminals Always 10 kΩ or higher
C109-1 (EGR4) or C58-32 (EGR4) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR