Home › Engine / Hybrid System › 6AR-FSE (EMISSION CONTROL) › EGR VALVE › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072205 6AR-FSE EMISSION CONTROL _0353746 EGR VALVE A

6AR-FSE EMISSION CONTROL  EGR VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

Hide 12601B 2.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17705 3.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 4.REMOVE BATTERY

Hide 82121 8.DISCONNECT ENGINE WIRE

a.
A412425

Remove the 2 bolts and nut.


b.
A412426

Using an E6 "TORX" socket wrench, remove the stud bolt and disconnect the engine wire.


c.
A412427

Remove the bolt.


d.

Disconnect the engine coolant temperature sensor connector.


Hide 9.REMOVE EGR VALVE WITH COOLER ASSEMBLY

a.
A412428

Disconnect the EGR valve assembly connector.


b.
A412429

Remove the engine cover joint and disconnect the fuel hose bracket from the EGR valve bracket.


c.
A412430

Remove the 4 bolts and 2 EGR valve brackets.


d.
A412431

Disengage the water hose from the hose clamp.


e.
A412432

Slide the clip and disconnect the water hose sub-assembly from the EGR cooler assembly.


f.
A412433C01
1.927,0.531 2.146,0.531 2.146,0.531 2.313,0.813 true 1.635,1.229 1.917,1.229 true 0.75,1.146 1.063,1.146 true 1.74,0.448 1.927,0.635 0.188,0.188 10 true *1 1.448,1.146 1.646,1.323 0.198,0.177 10 true *2 0.563,1.063 0.75,1.24 0.188,0.177 10 true *3
*1 No. 2 Water By-pass Hose
*2 No. 3 Water By-pass Hose
*3 No. 4 Water By-pass Hose


Slide the clip and disconnect the No. 2 water by-pass hose from the EGR valve assembly.


g.

Slide the clip and disconnect the No. 3 water by-pass hose from the EGR cooler assembly.


h.

Slide the clip and disconnect the No. 4 water by-pass hose from the EGR cooler assembly.


i.
A412434

Using a 12 mm deep socket wrench, remove the 2 nuts and EGR valve with cooler assembly from cylinder head sub-assembly.


j.
A338759

Remove the No. 2 EGR pipe gasket from the EGR valve assembly.


Hide 25620 10.REMOVE EGR VALVE ASSEMBLY

a.
A338761

Slide the clip and disconnect the No. 1 water by-pass hose from the EGR valve assembly.


b.
A338762

Remove the 2 nuts and EGR valve assembly from the EGR cooler assembly.


c.
A338988

Remove the EGR valve gasket from the EGR valve assembly.