The oil pump is a variable discharge type. The oil pump maintains the oil pressure in the required for VVT operation at low engine speeds and for lubrication at high engine speeds, and reduces friction to lower the excess oil pressure at middle engine speeds. The oil pressure sender gauge assembly detects the engine oil pressure.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P052012 | Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery | The oil pressure sender gauge assembly output voltage is higher than 4.78 V for 5 seconds or more (1 trip detection logic). | ·
Open or short in oil pressure sender gauge assembly circuit ·
Oil pressure sender gauge assembly ·
ECM |
Comes on | DTC stored | SAE Code:
P0523 |
| P052014 | Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open | The oil pressure sender gauge assembly output voltage is less than 0.23 V for 5 seconds or more (1 trip detection logic). | ·
Open or short in oil pressure sender gauge assembly circuit ·
Oil pressure sender gauge assembly ·
ECM |
Comes on | DTC stored | SAE Code:
P0522 |
| P052024 | Engine Oil Pressure Sensor/Switch "A" Signal Stuck High | The oil pressure sender gauge assembly output voltage is higher than the threshold value (1 trip detection logic). | ·
Open or short in oil pressure sender gauge assembly circuit ·
Oil pressure sender gauge assembly ·
ECM |
Comes on | DTC stored | SAE Code:
P0521 |
| P05202A | Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range | The oil pressure sender gauge assembly output voltage is the same value for a certain period of time (1 trip detection logic). | ·
Open or short in oil pressure sender gauge assembly circuit ·
Oil pressure sender gauge assembly ·
ECM |
Comes on | DTC stored | SAE Code:
P0521 |
| P052400 | Engine Oil Pressure Too Low | The oil pressure sender gauge assembly output voltage is at or below the threshold value (1 trip detection logic). | ·
Open or short in oil pressure sender gauge assembly circuit ·
Oil pressure sender gauge assembly ·
ECM ·
Engine oil amount insufficient |
Comes on | DTC stored | SAE Code:
P0524 |
The ECM calculates the engine oil pressure based on the output voltage of the oil pressure sender gauge assembly. If any of the following are detected, the ECM will illuminate the MIL and store a DTC.
The output voltage of the oil pressure sender gauge assembly is outside of the specified range.
The actual output voltage of the oil pressure sender gauge assembly is different than the estimated output voltage based on the engine speed.
The oil pressure sender gauge assembly output voltage does not change for a certain period of time.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switches turned off [A].
With the vehicle is stationary, gently depress the accelerator pedal and maintain an engine speed of 4000 rpm for 1 minute, then release the accelerator pedal and return to the engine idling [B].
Repeat step [B] 3 times or more.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P052012, P052014, P052024, P05202A or P052400.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P052012, P052014, P052024, P05202A and/or P052400 is output | A |
| DTC P052012, P052014, P052024, P05202A and/or P052400 and other DTCs are output | B |
If any DTCs other than P052012, P052014, P052024, P05202A an/or P052400 are output, troubleshoot those DTCs first.
A
B
Check the engine oil level.
Check the state of the oil level warning.
| Result | Proceed to |
|---|---|
| Engine oil level is within the specified range and oil level warning is not displayed | A |
| Engine oil level is low and oil level warning is displayed | B |
If the oil level warning is not displayed even though the engine oil level is below the Low mark, or the oil level warning is displayed even though the engine oil level is within the specified range, inspect the oil level sensor and related parts.
A
B
Check for engine oil leaks.
There are no engine oil leaks.
If there are engine oil leaks, perform the following steps after repairing or replacing the malfunctioning parts.
| Proceed to |
|---|
| NEXT |
NEXT
Add engine oil.
Click hereGeneral>MAINTENANCE>6AR-FSE OIL AND OIL FILTER>REPLACEMENT
Do not add engine oil to above the full level mark.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P052012, P052014, P052024, P05202A and/or P052400 is output | B |
A
B
Read the value displayed on the GTS.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature Sensor and Engine Oil Pressure.
| Tester Display |
|---|
| Engine Oil Temperature Sensor |
| Engine Oil Pressure |
With the engine oil temperature at 75 to 85°C (167 to 185°F), read the "Engine Oil Pressure" with the engine speed at 1000 rpm.
Read the oil pressure using an oil pressure gauge.
Install the oil pressure gauge.
Click hereEngine / Hybrid System>6AR-FSE (LUBRICATION)>LUBRICATION SYSTEM>ON-VEHICLE INSPECTION
Start the engine.
With the engine oil temperature at 75 to 85°C (167 to 185°F), read the oil pressure gauge with the engine speed at 1000 rpm.
Compare the Data List value and the oil pressure gauge reading.
Data List value and gauge reading are within +/-50 kPa of each other.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Oil Pressure Sender Gauge Assembly) |
Disconnect the oil pressure sender gauge assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C107-3 (VC) - Body ground | Engine switch on (IG) | 4.75 to 5.25 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the oil pressure sender gauge assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C107-2 (PEO) - C58-98 (PEO) | Always | Below 1 Ω |
| C107-1 (E2) - C58-129 (EPEO) | Always | Below 1 Ω |
| C107-2 (PEO) or C58-98 (PEO) - Body ground and other terminals | Always | 10 kΩ or higher |
| C107-1 (E2) or C58-129 (EPEO) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the oil pressure sender gauge assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C107-3 (VC) - C58-130 (VCPE) | Always | Below 1 Ω |
| C107-3 (VC) or C58-130 (VCPE) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the oil pressure sender gauge assembly.
Click hereEngine / Hybrid System>6AR-FSE (LUBRICATION)>OIL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P052012, P052014, P052024, P05202A and/or P052400 is output | B |
A
B