Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0351788 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

Result:
Result Proceed to
Automatic station search function does not stop A
Automatic station search function stops on a station B





A

2.CHECK OPTIONAL COMPONENTS

B

REPLACE RADIO RECEIVER ASSEMBLY

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film, are installed.

Result:
Result Proceed to
Optional components are not installed A
Optional components are installed B


NOTICE:

Do not remove optional components without the permission of the customer.




A

3.CHECK RADIO RECEIVER ASSEMBLY

B

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO RECEIVER ASSEMBLY
a.
E187251

Preparation for check

i.

Disconnect the antenna connector from the radio receiver assembly.



b.

Check for noise

i.

Turn the engine switch on (ACC) with the radio receiver assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.




Result:
Proceed to
OK
NG



OK

4.CHECK WINDOW GLASS ANTENNA WIRE

NG

REPLACE RADIO RECEIVER ASSEMBLY

4.CHECK WINDOW GLASS ANTENNA WIRE
a.
E111994C06
0.531,0.813 0.604,1.135 false 0.969,1.635 1.042,1.969 false 2.188,1.385 2.271,1.719 false 0.427,0.604 1.083,1.302 0.656,0.698 10 *a 0.948,1.969 1.375,2.354 0.427,0.385 10 *b 2.177,1.74 2.75,2.156 0.573,0.417 10 *c
*a Tester Probe
*b Antenna Wire
*c Tin Foil


Check for continuity of the window glass antenna wire.

NOTICE:

When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.


HINT:

Check for continuity at the center of each antenna wire as shown in the illustration.


OK:

There is continuity in the window glass antenna wire.



Result:
Proceed to
OK
NG



OK

5.INSPECT RADIO RECEIVER ASSEMBLY

NG

5.INSPECT RADIO RECEIVER ASSEMBLY
a.

Disconnect the RA1 radio receiver assembly connector.


b.
E188455C13
0.095,0.051 0.272,0.229 0.177,0.177 10 *a 0.737,0.971 1.032,1.121 0.295,0.15 10 RA1 0.705,1.404 1.108,1.576 0.403,0.171 10 ANT+ 1.552,1.083 1.136,1.404 false 0.624,0.909 1.16,1.201 0.536,0.292
*a Component without harness connected
(Radio Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RA1-5 (ANT+) - Body ground Engine switch on (ACC)
Radio switch on and AM or FM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

6.REPLACE ANTENNA CORD SUB-ASSEMBLY (for Front Side)

NG

REPLACE RADIO RECEIVER ASSEMBLY

6.REPLACE ANTENNA CORD SUB-ASSEMBLY (for Front Side)
a.

Replace the antenna cord sub-assembly (for front side) with a new or known good one and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END

NG

7.REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
7.REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Replace the No. 2 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



NG

8.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

OK

END

8.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly with a new or known good one and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



NG

9.REPLACE ANTENNA CORD SUB-ASSEMBLY (for Rear Side)

OK

END

9.REPLACE ANTENNA CORD SUB-ASSEMBLY (for Rear Side)
a.

Replace the antenna cord sub-assembly (for rear side) with a new or known good one and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.


Result:
Proceed to
OK
NG




OK

END

NG

REPLACE RADIO RECEIVER ASSEMBLY