Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0351788 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume based upon vehicle speed signals sent from the combination meter assembly.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E394332E02
1.521,0.271 2.802,0.51 1.281,0.24 10 false to Other Systems 1.063,2.271 2.927,2.51 1.865,0.24 10 false Combination Meter Assembly 1.063,2.094 1.5,2.333 0.438,0.24 10 false K21 4.563,2.094 5,2.333 0.438,0.24 10 false K144 4.563,2.271 6.281,2.51 1.719,0.24 10 false Radio Receiver Assembly 4.833,1.427 5.271,1.667 0.438,0.24 10 false SPD 2.115,1.438 2.552,1.677 0.438,0.24 10 false +S 2.448,1.292 2.885,1.531 0.438,0.24 10 false 6 4.573,1.292 5.01,1.531 0.438,0.24 10 false 17

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.

Check the output waveform.

E382308C02
1.74,0.25 2.229,0.521 0.49,0.271 2.698,1.833 2.323,1.167 false 0.281,0.167 0.594,0.323 0.313,0.156 10 false *a 1.854,0.302 2.313,0.5 0.458,0.198 10 false K21 2.667,1.844 2.979,2.042 0.313,0.198 10 false +S 6.042,1.458 6.5,1.656 0.458,0.198 10 false GND 4.646,1.656 4.802,1.854 0.156,0.198 10 false A
*a Component with harness connected
(Combination Meter Assembly)
- -


i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal K21-6 (+S) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal K21-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

2.INSPECT RADIO RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.

Check the output waveform.

E265791C54
1.646,0.271 2.063,0.531 0.417,0.26 2.604,1.844 2.406,1.406 false 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 1.698,0.313 2.083,0.521 0.385,0.208 10 false K144 2.5,1.854 2.813,2.052 0.313,0.198 10 false SPD 4.781,1.708 5.094,1.906 0.313,0.198 10 false A 6.167,1.469 6.594,1.688 0.427,0.219 10 false GND
*a Component with harness connected
(Radio Receiver Assembly)
- -


i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal K144-17 (SPD) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.



Item Condition
Measurement terminal K144-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR