Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2018.04–2021.02
RM33A0E _58 Vehicle Interior _065381 METER / GAUGE / DISPLAY _0323396 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU (brake actuator assembly) which uses this information to create the vehicle speed signal*. The vehicle speed signal consists of pulses sent to the combination meter assembly from the skid control ECU (brake actuator assembly). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the skid control ECU (brake actuator assembly). The pulse signal is created by switching the transistor in the skid control ECU (brake actuator assembly) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU (brake actuator assembly). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*: This vehicle speed signal is created by the skid control ECU (brake actuator assembly). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

E393837E01
0.104,1.479 0.917,1.708 0.813,0.229 10 false A34 0.094,1.646 2.99,2.073 2.896,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 1.427,0.729 1.865,0.948 0.438,0.219 10 false SP1 1.802,0.719 2.24,0.938 0.438,0.219 10 false 34 5.323,0.708 5.76,0.927 0.438,0.219 10 false 5 5.542,0.708 5.979,0.927 0.438,0.219 10 false SI 6.031,0.365 6.469,0.583 0.438,0.219 10 false 12 V 5.531,1.25 5.969,1.469 0.438,0.219 10 false +S 5.333,1.25 5.771,1.469 0.438,0.219 10 false 6 5.104,2.052 5.542,2.271 0.438,0.219 10 false K21 5.083,2.208 6.927,2.458 1.844,0.25 10 false Combination Meter Assembly 5.271,3.146 5.708,3.365 0.438,0.219 10 false 19 5.531,3.146 5.969,3.365 0.438,0.219 10 false SPD 4.177,3.667 4.615,3.885 0.438,0.219 10 false K62 4.167,3.844 7.156,4.115 2.99,0.271 10 false Certification ECU (Smart Key ECU Assembly)*6 5.469,5.25 5.906,5.469 0.438,0.219 10 false K17 5.458,5.406 6.604,5.646 1.146,0.24 10 false Navigation ECU*7 5.344,4.688 5.781,4.906 0.438,0.219 10 false 9 1.813,3.25 2.25,3.469 0.438,0.219 10 false A24 2.219,3.25 2.656,3.469 0.438,0.219 10 false A23 2.604,3.25 3.042,3.469 0.438,0.219 10 false A22 3.031,3.24 3.469,3.458 0.438,0.219 10 false C58 3.052,3.448 3.49,3.667 0.438,0.219 10 false *8 2.656,3.448 3.094,3.667 0.438,0.219 10 false *3 2.271,3.448 2.708,3.667 0.438,0.219 10 false *2 1.875,3.448 2.313,3.667 0.438,0.219 10 false *1 1.875,3.021 2.313,3.24 0.438,0.219 10 false 42 2.26,3.021 2.698,3.24 0.438,0.219 10 false 39 2.646,3.021 3.083,3.24 0.438,0.219 10 false 44 1.073,3.719 1.51,3.938 0.438,0.219 10 false ECM 0.115,5.25 0.552,5.469 0.438,0.219 10 false K3 0.104,5.406 2.635,5.656 2.531,0.25 10 false Radio and Display Receiver Assembly*4 0.188,6.781 0.625,7 0.438,0.219 10 false K10 0.167,6.948 2.698,7.229 2.531,0.281 10 false Stereo Component Amplifier Assembly*5 4.188,6.146 5.896,6.49 1.708,0.344 10 false *1: for A25A-FKS 4.188,7.146 6.875,7.396 2.688,0.25 10 false *4: w/ No. 1 Stereo Jack Adapter Assembly 4.198,7.5 5.406,7.729 1.208,0.229 10 false *5: for 9 Speakers 4.188,7.844 6.542,8.073 2.354,0.229 10 false *6: w/ Smart Entry and Start System 4.198,8.167 5.885,8.458 1.688,0.292 10 false *7: w/ Navigation System 1.781,6.208 2.219,6.427 0.438,0.219 10 false 11 1.802,4.677 2.24,4.896 0.438,0.219 10 false 27 5.531,4.698 5.969,4.917 0.438,0.219 10 false SPD 1.417,3.156 1.854,3.375 0.438,0.219 10 false SPD 1.406,4.688 1.844,4.906 0.438,0.219 10 false SPD 1.417,6.219 1.854,6.438 0.438,0.219 10 false SPD 3.021,3.021 3.458,3.24 0.438,0.219 10 false 44 4.188,6.479 5.896,6.823 1.708,0.344 10 false *2: for 2GR-FKS 4.198,6.813 5.906,7.156 1.708,0.344 10 false *3: for 2AR-FE 4.198,8.479 5.906,8.823 1.708,0.344 10 false *8: for 6AR-FSE

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Before replacing the ECM, certification ECU (smart key ECU assembly)*, refer to Service Bulletin.

*: w/ Smart Entry and Start System




PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
E188997C51
0.25,0.583 0.667,0.833 0.417,0.25 1.219,1.448 1.292,0.667 true 1.219,0.469 1.563,0.708 0.344,0.24 10 false +S 0.177,0.188 0.427,0.385 0.25,0.198 10 false *a 0.333,0.625 0.792,0.823 0.458,0.198 10 false K21
*a Front view of wire harness connector
(to Combination Meter Assembly)


a.

Disconnect the K21 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K21-6 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
E376462C01
1.51,0.177 1.927,0.427 0.417,0.25 1.052,0.417 1.25,0.906 false 1.604,0.219 2.063,0.417 0.458,0.198 10 false A34 0.906,0.25 1.365,0.448 0.458,0.198 10 false SP1 0.104,0.063 0.563,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


a.

Connect the K21 combination meter assembly connector.


b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-34 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - COMBINATION METER ASSEMBLY)
3.INSPECT SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (INPUT WAVEFORM)
E262405C43
1.521,0.396 1.896,0.646 0.375,0.25 2.25,1.229 2.365,0.625 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 1.583,0.438 1.917,0.646 0.333,0.208 10 false K21 2.302,0.427 2.5,0.635 0.198,0.208 10 false SI 2.948,3.698 3.396,4.021 0.448,0.323 10 false GND 1.292,3.99 1.604,4.198 0.313,0.208 10 false A
*a Component with harness connected
(Combination Meter Assembly)


a.

Check the input waveform.

i.

Connect the A34 skid control ECU (brake actuator assembly) connector.


ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal K21-5 (SI) and body ground.


iv.

Turn the ignition switch to ON.


v.

Turn a wheel slowly.


vi.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester connection K21-5 (SI) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - COMBINATION METER ASSEMBLY)
a.

Disconnect the K21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-34 (SP1) - K21-5 (SI) Always Below 1 Ω
A34-34 (SP1) or K21-5 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)
a.

Disconnect the A24*1 ECM connector.


b.

Disconnect the A23*2 ECM connector.


c.

Disconnect the A22*3 ECM connector.


d.

Disconnect the C58*8 ECM connector.


e.

Disconnect the K3 radio and display receiver assembly*4 connector.


f.

Disconnect the K62 certification ECU (smart key ECU assembly)*5 connector.


g.

Disconnect the K17 navigation ECU*6 connector.


h.

Disconnect the K10 stereo component amplifier assembly*7 connector.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-6 (+S) - Body ground Always 10 kΩ or higher



j.

Connect the A24*1 ECM connector.


k.

Connect the A23*2 ECM connector.


l.

Connect the A22*3 ECM connector.


m.

Connect the C58*8 ECM connector.


n.

Connect the K3 radio and display receiver assembly*4 connector.


o.

Connect the K62 certification ECU (smart key ECU assembly)*5 connector.


p.

Connect the K17 navigation ECU*6 connector.


q.

Connect the K10 stereo component amplifier assembly*7 connector.


*1: for A25A-FKS

*2: for 2GR-FKS

*3: for 2AR-FE

*4: w/ No. 1 Stereo Jack Adapter Assembly

*5: w/ Smart Entry and Start System

*6: w/ Navigation System

*7: for 9 Speakers

*8: for 6AR-FSE


Result:
Proceed to
OK
NG



OK

6.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

7.INSPECT NAVIGATION ECU (SHORT CIRCUIT IN NAVIGATION ECU)

B

8.CONFIRM MODEL
7.INSPECT NAVIGATION ECU (SHORT CIRCUIT IN NAVIGATION ECU)
a.

Disconnect the K17 navigation ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K21-6 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the navigation ECU.



Result:
Proceed to
OK
NG



OK

NG

8.CONFIRM MODEL
8.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ No. 1 Stereo Jack Adapter Assembly A
w/o No. 1 Stereo Jack Adapter Assembly B



A

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

10.CONFIRM MODEL
9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the K3 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K21-6 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio and display receiver assembly.



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

10.CONFIRM MODEL
10.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 9 Speakers A
except 9 Speakers B



A

11.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (SHORT CIRCUIT IN STEREO COMPONENT AMPLIFIER ASSEMBLY)

B

12.CONFIRM MODEL
11.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (SHORT CIRCUIT IN STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the K10 stereo component amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K21-6 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

12.CONFIRM MODEL
12.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Smart Entry and Start System A
w/o Smart Entry and Start System B



A

13.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (SHORT CIRCUIT IN CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

13.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (SHORT CIRCUIT IN CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K21-6 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the certification ECU (smart key ECU assembly).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG