Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0351788 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E372209E02
3.771,0.875 4.542,1.073 0.771,0.198 10 false PANEL 1.167,0.646 2.292,0.958 1.125,0.313 10 false from TAIL Relay 0.375,4.083 2.302,4.531 1.927,0.448 10 false Steering Pad Switch Assembly 0.833,2.583 1.146,2.781 0.313,0.198 10 false LH 0.833,3.427 1.146,3.625 0.313,0.198 10 false RH 5.479,5.917 7.125,6.344 1.646,0.427 10 false Radio Receiver Assembly 5.865,2.188 6.479,2.385 0.615,0.198 10 false ILL+ 5.885,5.198 6.5,5.396 0.615,0.198 10 false ILL- 2.448,5.74 4.292,6.031 1.844,0.292 10 false Combination Meter Assembly 2.469,5.552 2.927,5.75 0.458,0.198 10 false K21 3.385,5.188 3.844,5.427 0.458,0.24 10 false ILL- 3.125,2.094 3.896,2.292 0.771,0.198 10 false IL+2 3.125,2.656 3.896,2.854 0.771,0.198 10 false IL-2 2.667,2.188 2.979,2.385 0.313,0.198 10 false z1 3.688,2.177 4.146,2.375 0.458,0.198 10 false K22 3.729,1.99 4.042,2.188 0.313,0.198 10 false 14 3.76,2.563 4.073,2.76 0.313,0.198 10 false 9 2.688,1.99 3,2.188 0.313,0.198 10 false 1 2.688,2.563 3,2.76 0.313,0.198 10 false 6 5.531,2 5.844,2.198 0.313,0.198 10 false 10 5.583,4.99 5.74,5.188 0.156,0.198 10 false 5 3.708,5.052 3.865,5.25 0.156,0.198 10 false 1 5.458,2.198 6.073,2.396 0.615,0.198 10 false K152 5.458,5.177 6.073,5.375 0.615,0.198 10 false K151 2.448,3.198 4.292,3.802 1.844,0.604 10 false Spiral Cable Sub-assembly 3.688,2.75 4.146,2.948 0.458,0.198 10 false K22 2.667,2.75 2.979,2.948 0.313,0.198 10 false z1

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio receiver assembly. B
No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the K21 spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K21-14 (IL+2) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO RECEIVER ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the K152 radio receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K152-10 (ILL+) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK COMBINATION METER ASSEMBLY (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK COMBINATION METER ASSEMBLY (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the K151 radio receiver assembly connector.


b.

Disconnect the K21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K151-5 (ILL-) - K21-1 (ILL-) Always Below 1 Ω
K151-5 (ILL-) or K21-1 (ILL-) -Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR