Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0351788 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Mute Signal Circuit between Radio Receiver and Telematics Transceiver  


DESCRIPTION

The telematics transceiver sends a mute signal to the radio receiver assembly.

The radio receiver assembly controls the volume according to the mute signal from the telematics transceiver.

WIRING DIAGRAM

E394250E02
0.792,2.063 1.75,2.625 0.958,0.563 10 false Radio Receiver Assembly 0.792,1.917 1.333,2.115 0.542,0.198 10 false K152 1.271,1.01 1.885,1.208 0.615,0.198 10 false TMUT 1.74,0.917 1.896,1.115 0.156,0.198 10 false 8 5.271,0.917 5.583,1.115 0.313,0.198 10 false 17 5.531,1.021 6.146,1.219 0.615,0.198 10 false MUTE 5.208,1.906 5.823,2.104 0.615,0.198 10 false K145 5.219,2.073 6.74,2.479 1.521,0.406 10 false Telematics Transceiver

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)>PRECAUTION


PROCEDURE

1.INSPECT TELEMATICS TRANSCEIVER
a.
E259127C86
1.469,0.531 1.906,0.802 0.438,0.271 1.385,1.927 1.021,0.958 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.521,0.573 2.021,0.792 0.5,0.219 10 false K145 0.688,0.781 1.188,0.99 0.5,0.208 10 false MUTE
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K145-17 (MUTE) - Body ground Engine switch on (ACC)
Audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the K152 radio receiver assembly connector.


b.

Disconnect the K145 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K152-8 (TMUT) - K145-17 (MUTE) Always Below 1 Ω
K152-8 (TMUT) or K145-17 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO RECEIVER ASSEMBLY
a.

Reconnect the K152 radio receiver assembly connector.


b.
E176650C84
1.479,0.719 1.969,1.01 0.49,0.292 1.99,2.083 2.167,2.583 false 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.563,0.771 2.052,0.99 0.49,0.219 10 false K145
*a Front view of wire harness connector
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K145-17 (MUTE) - Body ground Engine switch on (ACC) 2.0 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO RECEIVER ASSEMBLY