Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2018.04
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Rear Television Camera Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Rear Television Camera Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Parking Assist Monitor System / Rear Camera" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Parking Assist Monitor System / Rear Camera" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Parking Assist Monitor System / Rear Camera" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Rear Television Camera Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Rear television camera assembly branch line or connector

·

Power source circuit of rear television camera assembly

·

Rear television camera assembly ground circuit

·

Rear television camera assembly



WIRING DIAGRAM

w/ Panoramic View Monitor System:
C381763E13
0.229,1.979 0.688,2.177 0.458,0.198 10 false R98 0.521,1.99 2.479,2.281 1.958,0.292 10 false No. 5 CAN Junction Connector 1.75,0.927 2.208,1.125 0.458,0.198 10 false 4 1.719,1.469 2.177,1.667 0.458,0.198 10 false 14 5.396,0.906 5.854,1.104 0.458,0.198 10 false 4 5.396,1.448 5.854,1.646 0.458,0.198 10 false 1 5.656,1.021 6.188,1.302 0.531,0.281 10 false CANH 5.646,1.583 6.177,1.865 0.531,0.281 10 false CANL 5.667,2.781 6.198,3.063 0.531,0.281 10 false CB+ 5.427,2.646 5.885,2.844 0.458,0.198 10 false 6 5.427,3.396 5.885,3.594 0.458,0.198 10 false 5 5.646,3.552 6.177,3.833 0.531,0.281 10 false CGND 0.708,3.531 2.927,3.948 2.219,0.417 10 false to Television Camera Controller 5.073,4.729 5.604,5.01 0.531,0.281 10 false m4 5.344,4.729 6.823,5.198 1.479,0.469 10 false Rear Television Camera Assembly 3.865,2.635 4.667,2.896 0.802,0.26 10 false ECU-ACC 1.698,2.781 2.813,3.104 1.115,0.323 10 false from ACC Relay

w/ Parking Assist Monitor System:
C384912E02
0.302,2.021 0.76,2.219 0.458,0.198 10 false R98 0.625,2.021 2.688,2.448 2.063,0.427 10 false No. 5 CAN Junction Connector 5.406,0.906 5.865,1.104 0.458,0.198 10 false 4 1.729,1.469 2.188,1.667 0.458,0.198 10 false 14 1.75,0.906 2.208,1.104 0.458,0.198 10 false 4 5.396,1.458 5.854,1.656 0.458,0.198 10 false 1 5.667,1.042 6.188,1.271 0.521,0.229 10 false CANH 5.667,1.594 6.188,1.823 0.521,0.229 10 false CANL 0.323,2.76 3.094,3.219 2.771,0.458 10 false from Radio and Display Receiver Assembly 0.469,3.448 3.24,3.906 2.771,0.458 10 false to Radio and Display Receiver Assembly 5.406,3.333 5.865,3.531 0.458,0.198 10 false 5 5.406,2.635 5.865,2.833 0.458,0.198 10 false 6 5.667,2.771 6.125,2.969 0.458,0.198 10 false CB+ 5.656,3.469 6.208,3.719 0.552,0.25 10 false CGND 5.26,4.781 5.813,5.031 0.552,0.25 10 false m3 5.552,4.781 7.052,5.448 1.5,0.667 10 false Rear Television Camera Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Panoramic View Monitor System A
w/ Parking Assist Monitor System B



A

2.CHECK FOR OPEN IN CAN BUS LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)

B

4.CHECK FOR OPEN IN CAN BUS LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)
2.CHECK FOR OPEN IN CAN BUS LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the m4 rear television camera assembly connector.


c.
C376603C12
1.5,0.094 1.854,0.365 0.354,0.271 1.438,1.49 1.438,0.542 1.438,0.542 1.271,0.542 true 1.448,2 1.448,2.781 1.448,2.781 1.281,2.781 true 0.104,0.073 0.417,0.292 0.313,0.219 10 false *a 1.583,0.146 1.896,0.365 0.313,0.219 10 false m4 0.833,0.469 1.292,0.76 0.458,0.292 10 false CANL 0.813,2.708 1.271,3 0.458,0.292 10 false CANH
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
m4-4 (CANH) - m4-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C376603C13
1.5,0.177 1.854,0.448 0.354,0.271 1.729,2 1.729,2.781 1.729,2.781 1.563,2.781 true 2.021,2.01 2.021,2.792 2.021,2.792 2.188,2.792 true 0.104,0.073 0.417,0.292 0.313,0.219 10 false *a 1.583,0.24 1.896,0.458 0.313,0.219 10 false m4 2.281,2.719 2.74,3.01 0.458,0.292 10 false CB+ 1.094,2.708 1.552,3 0.458,0.292 10 false CGND
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
m4-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
m4-6 (CB+) - Body ground Ignition switch ACC 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK FOR OPEN IN CAN BUS LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the m3 rear television camera assembly connector.


c.
C386092C01
1.49,0.177 1.875,0.469 0.385,0.292 1.5,1.583 1.5,0.667 1.5,0.667 1.333,0.667 true 1.51,2.031 1.51,2.781 1.51,2.781 1.344,2.781 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.583,0.25 1.896,0.448 0.313,0.198 10 false m3 0.896,0.594 1.406,0.865 0.51,0.271 10 false CANL 0.885,2.698 1.438,2.969 0.552,0.271 10 false CANH
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
m3-4 (CANH) - m3-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C386092C02
1.49,0.177 1.875,0.469 0.385,0.292 1.708,2.042 1.708,2.792 1.708,2.792 1.542,2.792 true 1.917,2.042 1.917,2.792 1.917,2.792 2.083,2.792 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.583,0.25 1.896,0.448 0.313,0.198 10 false m3 2.167,2.719 2.677,2.99 0.51,0.271 10 false CB+ 1.083,2.719 1.635,2.99 0.552,0.271 10 false CGND
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
m3-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
m3-6 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)