Home › Engine / Hybrid System › 6AR-FSE (FUEL) › FUEL INJECTOR (for Port Injection) › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072204 6AR-FSE FUEL _0353735 FUEL INJECTOR(for Port Injection) G

6AR-FSE FUEL  FUEL INJECTOR(for Port Injection)  INSPECTION  


PROCEDURE

Hide 23250F 1.INSPECT PORT FUEL INJECTOR ASSEMBLY

a.

Check the resistance.

i.
A335666C02
0.104,0.104 0.417,0.26 0.313,0.156 10 false *a
*a Component without harness connected
(Port Fuel Injector Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the port fuel injector assembly.



b.

Check the operation.

CAUTION:

Perform the inspection in a well-ventilated area.

Do not perform the inspection near an open flame.


i.
A411919

Disengage the 2 claws to remove the No. 2 fuel pipe clamp.


ii.
A393279

Remove the fuel pipe clamp from the fuel tube connector.


iii.
A411920

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION


iv.
A264971C19
0.5,1.656 0.729,1.885 0.729,1.885 0.833,1.885 false 0.854,0.906 1.146,0.615 1.146,0.615 1.26,0.615 false 1.99,1.292 2.292,1.594 2.292,1.594 2.417,1.594 false 2.646,0.698 2.948,0.396 2.948,0.396 3.063,0.396 false 0.875,1.802 1.156,2.042 0.281,0.24 10 false *a 1.333,0.521 1.656,0.781 0.323,0.26 10 false *b 2.479,1.51 2.802,1.76 0.323,0.25 10 false *c 3.135,0.292 3.354,0.542 0.219,0.25 10 false *d
*a SST (Hose)
*b SST (Hose Band)
*c SST (Fuel Tube Connector)
*d Fuel Pipe (Vehicle Side)


Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).

SST
09268-31015  (09268-41500, 09268-41700, 95336-08070)

NOTICE:

Make sure the SST (fuel tube connector) O-rings are not damaged and are free of foreign matter as they are used to seal the connections between the fuel tube connector and fuel pipe.



v.

Apply a light coat of gasoline to a new O-ring. Then install the O-ring to the port fuel injector assembly.


vi.
A300546C06
1.917,0.302 2.427,0.302 false 1.094,0.688 1.542,0.688 false 1.073,0.938 1.292,0.938 1.292,0.938 1.563,1.01 false 1.094,2.01 1.563,2.01 false 2.469,1.531 2.854,1.531 false 1.281,0.125 1.552,0.125 false 0.896,0.875 1.208,1.031 0.313,0.156 10 false *1 0.917,0.604 1.229,0.76 0.313,0.156 10 false *a 2.479,0.229 2.792,0.385 0.313,0.156 10 false *b 2.906,1.458 3.219,1.615 0.313,0.156 10 false *c 0.927,1.938 1.24,2.094 0.313,0.156 10 false *e 1.104,0.042 1.417,0.198 0.313,0.156 10 false *d
*1 O-ring
*a SST (Adapter)
*b SST (Hose Band)
*c SST (Clamp)
*d SST (Hose)
*e Vinyl Tube


Connect SST (adapter) and SST (hose) to the port fuel injector assembly, and hold the port fuel injector assembly and union with SST (clamp).

SST
09268-31015  (09268-41600, 09268-41300, 09268-41700, 95336-08070)


vii.
A300548C09
1.51,1.677 1.802,1.979 1.802,1.979 1.99,1.979 true 1.677,1.302 2.313,1.677 2.313,1.677 2.542,1.677 true 2.604,1.594 2.917,1.75 0.313,0.156 10 false *a 2.052,1.896 2.51,2.094 0.458,0.198 10 false *b
*a Lock
*b SST (Tie Band)


Tie SST (clamp) and SST (adapter) together with SST (tie band) as shown in the illustration.

SST
09268-31015  (09268-41800)

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no wear, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



viii.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


ix.

Install a vinyl tube to the port fuel injector assembly.

CAUTION:

Install a suitable vinyl tube to the port fuel injector assembly to prevent fuel from spraying.



x.

Set the port fuel injector assembly into a graduated cylinder.


xi.

Connect the GTS to the DLC3.


xii.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



xiii.

Turn the GTS on.


xiv.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 24

xv.
A300547C05
2.063,0.958 1.854,0.958 1.854,0.958 1.708,0.354 false 2.104,0.896 2.417,1.052 0.313,0.156 10 false *a
*a SST (EFI Inspection Wire H)


Connect SST (EFI inspection wire H) to the port fuel injector assembly and battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each port fuel injector assembly 2 or 3 times.

SST
09842-30080  

Standard Injection Volume:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - Negative (-) battery terminal Per 15 seconds 54 to 65 cc (3.3 to 4.0 cu. in.)


Difference between Each Port Fuel Injector Assembly:

11 cc (0.7 cu. in.) or less


NOTICE:
·

Make sure that SST (EFI inspection wire H) is securely connected.

·

Always switch the voltage on and off at the battery side, not the port fuel injector assembly side.



If the injection volume is not as specified, replace the port fuel injector assembly.



c.

Check for leaks.

i.

Disconnect SST (EFI inspection wire H) from the battery and check for fuel leaks from the port fuel injector assembly.

Standard Fuel Drop:

1 drop or less per 23 minutes


If the result is not as specified, replace the port fuel injector assembly.


ii.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION


iii.

Install the fuel pipe clamp to the fuel tube connector.


iv.

Engage the 2 claws to install the No. 2 fuel pipe clamp.