Home › Engine / Hybrid System › 6AR-FSE (FUEL) › FUEL SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072204 6AR-FSE FUEL _0353734 FUEL SYSTEM G

6AR-FSE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP WITH FILTER ASSEMBLY OPERATION AND INSPECT FOR FUEL LEAK

a.

Check fuel pump with filter assembly operation.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 24

v.

Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the relay, fuel pump with filter assembly, ECM and wiring connectors.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



c.

Turn the engine switch off.


d.

Disconnect the GTS from the DLC3.


Hide 2.CHECK FUEL PRESSURE

a.

Discharge fuel system pressure.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Measure the battery voltage.

Standard Voltage:

11 to 14 V



c.

Remove the No. 1 engine cover sub-assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL



e.

Disconnect the No. 2 fuel tube sub-assembly (for Direct Injection).

i.
A337352

Disconnect the No. 2 fuel tube sub-assembly from the No. 1 fuel pipe.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION



f.

Disconnect the fuel tube sub-assembly (for Port Injection).

i.
A337353

Disconnect the fuel tube sub-assembly from the fuel delivery pipe.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION



g.
A326520C03
0.354,0.771 0.521,0.771 0.521,0.771 0.667,1.271 false 2.365,0.5 2.698,0.5 false 1.927,1.24 1.927,0.99 false 1.385,2.438 1.385,2.021 false 3.156,3.375 2.76,3.375 false 2.073,3.25 1.844,3.25 false 2.083,3.917 1.792,3.917 false 3,0.833 2.917,0.833 2.917,0.833 2.75,1.167 true 2.125,2.469 1.896,2.469 false 1.969,4.365 1.74,4.365 false 2.74,0.417 3.052,0.573 0.313,0.156 10 false *a 1.875,1.271 2.188,1.427 0.313,0.156 10 false *b 0.177,0.677 0.49,0.833 0.313,0.156 10 false *c 1.313,2.458 1.625,2.615 0.313,0.156 10 false *d 2.563,3.281 2.875,3.438 0.313,0.156 10 false *e 2.125,3.833 2.438,3.99 0.313,0.156 10 false *f 3.042,0.75 3.354,0.906 0.313,0.156 10 false *a 2.104,3.167 2.417,3.323 0.313,0.156 10 false *a 1.729,2.385 2.042,2.542 0.313,0.156 10 false *1 2.021,4.26 2.313,4.479 0.292,0.219 10 false *g
*1 Fuel Tube Sub-assembly (Vehicle Side)
*a SST (Hose Band)
*b SST (T-joint)
*c SST (Gauge)
*d SST (Hose Joint)
*e SST (Hose)
*f SST (Fuel Tube Connector)
*g Fuel Pipe (Vehicle Side)


Install SST (EFI fuel pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)


h.

Wipe up any spilled fuel.


i.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



j.

Connect the GTS to the DLC3.


k.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



l.

Turn the GTS on.


m.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 24

n.

Measure the fuel pressure.

Standard Fuel Pressure:

196 to 588 kPa (2.0 to 6.0 kgf/cm2, 28 to 85 psi)


·

If the fuel pressure is more than the standard, replace the fuel pressure regulator assembly.

·

If the fuel pressure is less than the standard, check the fuel hoses and their connections, fuel pump with filter assembly and fuel pressure regulator assembly.



o.

Disconnect the GTS from the DLC3.


p.

Start the engine.


q.

Measure the fuel pressure at idle.

Standard Fuel Pressure:

196 to 588 kPa (2.0 to 6.0 kgf/cm2, 28 to 85 psi)


HINT:

Refer to Standard Idle Speed.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION



r.

Stop the engine.


s.

Check that the fuel pressure remains as specified for 5 minutes.

Standard Fuel Pressure:

147 kPa (1.5 kgf/cm2, 21 psi)


If the result is not as specified, check the fuel pump with filter assembly, fuel pressure regulator assembly and/or port fuel injector assemblies.


t.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST to prevent fuel from spraying.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



u.

Connect the fuel tube sub-assembly (for Port Injection).

i.

Connect the fuel tube sub-assembly to the fuel delivery pipe.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION



v.

Connect the No. 2 fuel tube sub-assembly (for Direct Injection).

i.

Connect the No. 2 fuel tube sub-assembly to the No. 1 fuel pipe.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION




x.

Install the No. 1 engine cover sub-assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION



Hide 3.CHECK FUEL PRESSURE (for High Pressure)

a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Coolant Temperature, Fuel Pressure (High) and Injection Mode.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Coolant Temperature
Fuel Pressure (High)
Injection Mode
50003 372 211,205,265,294

e.

According to the display on the GTS, read the Data List.

Standard:
GTS Display Condition Specified Condition
Fuel Pressure (High)
·

Shift position: P

·

A/C: Off

·

Engine warmed up

·

Engine Speed: 3000 rpm

·

Injection Mode: Direct


2000 to 20000 kPa


If the result is not as specified, check the fuel pump with filter assembly, fuel pump with seal sub-assembly, fuel pressure sensor (fuel delivery pipe sub-assembly) and wire harnesses.


f.

Stop the engine.