Home › Engine / Hybrid System › 6AR-FSE (FUEL) › FUEL PUMP (for High Pressure) › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072204 6AR-FSE FUEL _0353739 FUEL PUMP(for High Pressure) A

6AR-FSE FUEL  FUEL PUMP(for High Pressure)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump with seal sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
·

Replacement of fuel pump with seal sub-assembly

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 22030 4.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 5.REMOVE FUEL PUMP PROTECTOR

a.
A412593

Remove the 2 bolts and fuel pump protector from the cylinder head cover sub-assembly.


Hide 6.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A425219

Disconnect the No. 2 fuel tube sub-assembly from the No. 1 fuel pipe.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23811B 7.REMOVE NO. 1 FUEL PIPE

a.
A412633C01
1.948,1.615 2.198,1.76 2.198,1.76 2.365,1.76 true 2.417,1.677 2.625,1.833 0.208,0.156 10 true *a
*a 17 mm Deep Socket Wrench


Using a 17 mm deep socket wrench, remove the No. 1 fuel pipe and gasket from the fuel pump with seal sub-assembly.


Hide 23801P 8.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A412635

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


b.
A337377

Loosen the 2 bolts of the fuel pump with seal sub-assembly.


c.

Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe sub-assembly and fuel pump with seal sub-assembly.


Hide 23021 9.REMOVE FUEL PUMP WITH SEAL SUB-ASSEMBLY

a.
A339043

Disconnect the fuel pump with seal sub-assembly connector.


b.

Remove the 2 bolts and fuel pump with seal sub-assembly from the cylinder head cover sub-assembly.


c.
A337332C03
0.792,0.573 1.177,0.573 false 0.729,1.969 1.115,1.969 false 1.104,2.771 1.49,2.771 false 0.625,3.833 1.01,3.833 false 0.604,0.51 0.917,0.667 0.313,0.156 10 false *1 0.542,1.906 0.854,2.063 0.313,0.156 10 false *2 0.917,2.708 1.229,2.865 0.313,0.156 10 false *3 0.427,3.771 0.74,3.927 0.313,0.156 10 false *4
*1 Fuel Pump with Seal Sub-assembly
*2 Fuel Pump Insulator
*3 Fuel Pump Lifter Assembly
*4 Fuel Pump Lifter Guide


Remove the fuel pump lifter guide, fuel pump lifter assembly and fuel pump insulator from the fuel pump with seal sub-assembly.


d.
A337333

Remove the O-ring from the fuel pump with seal sub-assembly.


e.
A338469C01
0.51,1.25 0.74,1.25 true 0.615,1.813 0.74,1.813 0.74,1.813 1.063,1.396 true 2.26,0.583 2.615,0.271 2.615,0.271 2.75,0.271 true 0.333,1.177 0.646,1.333 0.313,0.156 10 false *1 0.438,1.74 0.75,1.896 0.313,0.156 10 false *2 2.802,0.198 3.115,0.354 0.313,0.156 10 false *2
*1 Fuel Pump Spacer Gasket
*2 O-ring


Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly.


f.

Remove the 2 O-rings from the No. 4 camshaft bearing cap.