Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2018.04–2021.02
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328237 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the engine switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B278A Short to GND in Immobiliser System Power Source Circuit A short to GND in the power supply of the transponder key amplifier of the engine switch (VC5 - VC5) detected. (1 trip detection logic*)
·

Engine switch

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC output confirmation operation:

With the shift lever in P and the electrical key transmitter sub-assembly held near the engine switch, an engine start operation is performed by pressing and holding the engine switch when the transmitter battery is depleted.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when transmitter battery is depleted by holding transmitter near engine switch and pressing and holding engine switch with shift lever in P -

Related Data List and Active Test
DTC No. Data List and Active Test
B278A -

WIRING DIAGRAM

B463088E01
0.604,3.25 2.594,3.448 1.99,0.198 10 false Engine Switch 0.615,3.104 2.604,3.302 1.99,0.198 10 false K63 5.271,3.25 6.792,3.698 1.521,0.448 10 false Certification ECU (Smart Key ECU Assembly) 5.281,3.094 6.625,3.417 1.344,0.323 10 false K62 5.24,2.323 5.854,2.583 0.615,0.26 10 false AGND 5.24,1.823 5.854,2.083 0.615,0.26 10 false CODE 5.25,1.188 5.865,1.448 0.615,0.26 10 false TXCT 5.25,0.677 5.865,0.938 0.615,0.26 10 false VC5 5.917,1.458 6.531,1.719 0.615,0.26 10 false 5 V 5.927,0.125 6.542,0.385 0.615,0.26 10 false 5 V 1.427,2.302 2.042,2.563 0.615,0.26 10 false AGND 1.427,1.813 2.042,2.073 0.615,0.26 10 false CODE 1.469,1.281 2.083,1.542 0.615,0.26 10 false TXCT 1.542,0.771 2.156,1.031 0.615,0.26 10 false VC5 1.906,2.302 2.198,2.552 0.292,0.25 10 false 6 1.917,1.802 2.208,2.052 0.292,0.25 10 false 8 1.917,1.188 2.208,1.438 0.292,0.25 10 false 7 1.906,0.656 2.198,0.906 0.292,0.25 10 false 10 4.99,2.323 5.281,2.573 0.292,0.25 10 false 11 5.052,1.813 5.344,2.063 0.292,0.25 10 false 6 5.063,1.188 5.354,1.438 0.292,0.25 10 false 5 5.073,0.667 5.365,0.917 0.292,0.25 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Using an oscilloscope, check the waveform.

B345599C69
1.885,0.385 2.302,0.635 0.417,0.25 1.635,2.354 1.865,2.354 1.865,2.354 1.865,1.635 true 2.583,2.344 2.333,2.344 2.333,2.344 2.333,1.646 true 1.042,0.573 1.625,1.031 0.583,0.458 10 false *a 1.958,0.417 2.865,0.938 0.906,0.521 10 false K63 6.51,1.354 7.156,1.74 0.646,0.385 10 false GND 1.323,2.271 1.635,2.469 0.313,0.198 10 false VC5 2.625,2.26 3.188,2.5 0.563,0.24 10 false AGND
*a Component with harness connected
(Engine Switch)
- -


HINT:

Perform this inspection on the engine switch side.


OK:
Tester Connection Condition Tool Setting Specified Condition
K63-10 (VC5) - K63-6 (AGND) Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed 2 V/DIV., 200 ms./DIV. Pulse generation



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K63 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-7 (VC5) - K63-10 (VC5) Always Below 1 Ω
K62-11 (AGND) - K63-6 (AGND) Always Below 1 Ω
K62-7 (VC5) or K63-10 (VC5) - Other terminals and body ground Always 10 kΩ or higher
K62-11 (AGND) or K63-6 (AGND) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the K62 certification ECU (smart key ECU assembly) connector.


b.

Connect the K63 engine switch connector.


c.

Measure the voltage according to the value(s) in the table below.

B416787C28
4.583,0.417 5,0.667 0.417,0.25 4.469,2.271 4.75,2.271 4.75,2.271 4.75,1.323 true 5.292,2.271 5.073,2.271 5.073,2.271 5.073,1.323 true 4.667,0.458 4.979,0.656 0.313,0.198 10 false K62 4.031,2.188 4.594,2.417 0.563,0.229 10 false AGND 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 5.354,2.188 5.813,2.396 0.458,0.208 10 false VC5
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition
K62-7 (VC5) - K62-11 (AGND) Engine switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)