The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during main body ECU (multiplex network body ECU) removal/installation are shown below.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for LHD)
for 2AR-FE:
Click hereGeneral>MAINTENANCE>2AR-FE BATTERY>REMOVAL
for A25A-FKS:
Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>REMOVAL
for 2GR-FKS:
Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL
for 6AR-FSE:
3. DISCHARGE DOOR CONTROL BATTERY AND DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Door Control Battery)
Always ensure that the cable is disconnected from the negative (-) battery terminal and the door control battery is fully discharged when removing or installing the junction block assembly.
Make sure to perform the following procedure before removal and installation of the junction block assembly.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
When the engine switch is turned off after the door control battery is fully charged, the door control battery becomes completely discharged due to self-discharge within approximately 30 minutes.
Approximately 90 seconds after the engine switch is turned on (IG), the door control battery becomes fully charged.
When approximately 30 minutes or more have elapsed after the engine switch is turned off, the Active Test may not be able to be performed.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
| Tester Display | Control Range |
|---|---|
| Shock Detection Unlock | ON/OFF |
Do not perform the Active Test at this time.
Disconnect the cable from the negative (-) battery terminal.
Perform the "Shock Detection Unlock" Active Test repeatedly until the multiplex network body ECU (main body ECU) communication lost error message "Lost communication with vehicle" is displayed on the GTS.
| Tester Display |
|---|
| Shock Detection Unlock |
When the cable is disconnected from the negative (-) battery terminal and the door control battery becomes completely discharged, the multiplex network body ECU (main body ECU) communication lost message "Lost communication with vehicle" is displayed on the GTS.
The number of times the Active Test can be performed depends on the charge condition of the door control battery.
73900
4.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)
55308B
5.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for LHD)
67914
6.REMOVE FRONT DOOR SCUFF PLATE LH (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62112A
7.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62312B
8.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
55318C
9.REMOVE INSTRUMENT SIDE PANEL LH (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
55607
10.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
55435B
11.REMOVE NO. 1 METER HOOD CLUSTER (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL
55012A
12.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL
55476C
13.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL
55303B
14.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
15.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU
for LHD:
Disconnect each connector.
Disengage the clamp.
|
Remove in this Direction |
Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration.
Disconnect each connector.
Remove the 2 nuts.
|
Remove in this Direction |
Disengage the claw and guide and pull out the instrument panel junction block assembly with main body ECU.
Disengage the clamp.
Disengage the clamp.
|
Remove in this Direction |
Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration and remove the instrument panel junction block assembly with main body ECU.
for RHD:
Disconnect each connector.
|
Remove in this Direction |
Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration.
Remove the 2 nuts.
Disengage the clamp.
|
Remove in this Direction |
Disengage the claw and guide and pull out the instrument panel junction block assembly with main body ECU.
Disengage the clamp.
Disengage the clamp.
|
Remove in this Direction |
Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration and remove the instrument panel junction block assembly with main body ECU.
82715
16.REMOVE WIRING HARNESS CLAMP BRACKET
Remove the nut.
Disengage the guide to remove the wiring harness clamp bracket.
17.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *1 | Instrument Panel Junction Block Assembly |
| *2 | Main Body ECU (Multiplex Network Body ECU) |
|
Push in this Direction |
Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.
| *a | Protective Tape |
|
Insert in this Direction |
|
Remove in this Direction |
With the instrument panel junction block assembly lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the main body ECU (multiplex network body ECU) and junction block assembly.
Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).
Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).
Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.
Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.
Do not touch the main body ECU (multiplex network body ECU) connector.