The ECM sends the reverse signal to the main body ECU (multiplex network body ECU) via CAN communication. When receiving the reverse signal, the main body ECU (multiplex network body ECU) sends the reverse request signal to each outer mirror control ECU assembly. Based on the signal, each outer mirror control ECU assembly then performs control.
The power mirror control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
The reverse shift-linked function will not activate when both the mirror select switch L and R switch are off.
| *a | Turn to Fully Left Position |
Turn the engine switch on (IG).
Using the outer mirror switch assembly, turn the mirror surface to the fully left position.
Press the M1 switch while the SET switch is being pressed.
Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.
Using the outer mirror switch assembly, turn the mirror surface to the fully right position.
Press the M1 switch.
Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.
| Result | Proceed to |
|---|---|
| Memory and reactivation functions are normal | A |
| Memory function is not normal | B |
| Reactivation function is not normal | C |
A
B
C
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Check if SFI system DTCs are output. (for 2AR-FE)
Enter the following menus: Powertrain / Engine / DTC.
Check if SFI system DTCs are output. (for 2GR-FKS)
SFI system DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the shift position indicator light in the combination meter assembly operates normally.
Shift position indicator light indicates the actual shift position correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| *a | Turns Downward |
Turn the engine switch on (IG).
Turn the mirror select switch R or L switch on.
Check that the mirror surface turns downward when the shift lever is moved to R.
| Result | Proceed to |
|---|---|
| Reverse shift-linked functions on both mirrors are not normal | A |
| Reverse shift-linked function on driver door is not normal | B |
| Reverse shift-linked function on front passenger door is not normal | C |
A
B
C
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mirror Selection SW (R) | Mirror select switch signal for RH mirror | OFF or ON | OFF: Mirror select switch off
ON: Mirror select switch R switch on |
- |
| Mirror Selection SW (L) | Mirror select switch signal for LH mirror | OFF or ON | OFF: Mirror select switch off
ON: Mirror select switch L switch on |
- |
| Tester Display |
|---|
| Mirror Selection SW (R) |
| Mirror Selection SW (L) |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG