Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL INJECTOR (for Direct Injection) › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _065334 2GR-FKS FUEL _0319415 FUEL INJECTOR(for Direct Injection) A

2GR-FKS FUEL  FUEL INJECTOR(for Direct Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Replacement of fuel injector assembly (for Port Injection)

·

Replacement of fuel injector assembly (for Direct Injection)

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



PROCEDURE

Hide 23100X 1.REMOVE FUEL PUMP ASSEMBLY (for High Pressure)

Hide 23802B 2.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY

CAUTION:

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.


a.
A405961

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 2 fuel pipe sub-assembly.


b.

Remove the No. 2 fuel pipe sub-assembly from the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH.


Hide 3.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A405963

Disconnect the No. 6 engine wire connector and No. 7 engine wire connector.


b.
A405964

Disengage the 2 clamps to remove the wire harness clamp bracket.


Hide 23860 4.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY LH

a.
A405965

Disconnect the fuel pressure sensor connector.


b.
A405966

Remove the bolt.


c.

Disengage the clamp to disconnect the No. 7 engine wire from the fuel delivery pipe with sensor assembly LH.


d.
A405967C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, 2 nuts and fuel delivery pipe with sensor assembly LH with the 3 fuel injector assemblies from the cylinder head LH.

NOTICE:
·

Make sure not to touch or strike the tips of the fuel injector assemblies.

·

Pull and remove the fuel delivery pipe with sensor assembly LH in a straight line without tilting it.




e.
A368871

Disconnect the 3 fuel injector assembly connectors.


Hide 23814E 5.REMOVE FUEL DELIVERY PIPE RH

a.
A405968

Remove the bolt.


b.

Disengage the clamp to disconnect the No. 6 engine wire from the fuel delivery pipe RH.


c.
A405969C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, 2 nuts and fuel delivery pipe RH with the 3 fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:
·

Make sure not to touch or strike the tips of the fuel injector assemblies.

·

Pull and remove the fuel delivery pipe RH in a straight line without tilting it.




d.
A368872

Disconnect the 3 fuel injector assembly connectors.


Hide 23250 6.REMOVE FUEL INJECTOR ASSEMBLY

a.
A361016N01
2.333,2.75 3,3.052 0.667,0.302 10 true No. 2

Secure the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH in a vise between aluminum plates and pull out the 6 fuel injector assemblies.

NOTICE:
·

Pull and remove each fuel injector assembly in a straight line to avoid damaging the seal surface of the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH O-ring.

·

After removing the fuel injector assemblies, remove any O-rings, No. 1 fuel injector back-up rings and No. 3 fuel injector back-up rings remaining on the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH side.

·

Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.




b.

Remove the nozzle holder clamp from each fuel injector assembly.


c.

Using needle nose pliers, remove the No. 3 fuel injector back-up ring from each fuel injector assembly.

NOTICE:

Do not damage the area that contacts the O-ring.



d.

Remove the O-ring and No. 1 fuel injector back-up ring from each fuel injector assembly.


e.

Remove the C-ring and injector vibration insulator from each fuel injector assembly.


Hide 23255A 7.REMOVE FUEL INJECTOR SEAL

a.
A361017

Using the tip of needle nose pliers, pinch and pull the fuel injector seal at several points to stretch it.

NOTICE:
·

Excessively pinching the fuel injector seal may damage the groove of the fuel injector assembly.

·

If a fuel injector assembly is dropped or the tip of the fuel injector assembly is struck, replace it with a new one.




b.

Remove the fuel injector seal from each fuel injector assembly.