Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › 2019.10–2020.08
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0329531 LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System)  Clearance Light/Daytime Running Light Circuit  


DESCRIPTION

Clearance light function:

When the main body ECU (multiplex network body ECU) receives the light control switch position signal, it sends an illumination request signal to the headlight ECU sub-assembly LH/RH and illuminates the clearance lights.


Daytime running light function:

When the operation conditions of the daytime running lights are met, the main body ECU (multiplex network body ECU) sends an illumination request signal to the headlight ECU sub-assembly LH/RH and illuminates the daytime running lights.


WIRING DIAGRAM

for Bulb Type Turn Signal Light


E380629E01
0.073,6.26 2.021,6.552 1.948,0.292 10 false Headlight ECU Sub-assembly 2.906,5.969 4.854,6.26 1.948,0.292 10 false Headlight Unit Assembly 3.865,5.396 6.177,5.667 2.313,0.271 10 false No. 1 Headlight Clearance LED Unit 3.469,3.052 4.438,3.625 0.969,0.573 10 false Electronic Light Source Control Gear B 3.458,1.146 4.427,1.719 0.969,0.573 10 false Electronic Light Source Control Gear A 4.99,1.573 6.521,2.281 1.531,0.708 10 false Clearance Light/Daytime Running Light 0.073,6.125 0.385,6.365 0.313,0.24 10 false B 0.99,4.344 1.396,4.604 0.406,0.26 10 false DRL+ 0.99,4.688 1.396,4.948 0.406,0.26 10 false DRL- 0.979,5.021 1.385,5.281 0.406,0.26 10 false CLL+ 2.979,5.052 3.208,5.271 0.229,0.219 10 false G 2.979,4.708 3.208,4.927 0.229,0.219 10 false G 2.979,4.365 3.208,4.583 0.229,0.219 10 false G 2.99,4.042 3.219,4.26 0.229,0.219 10 false G 2.99,3.698 3.219,3.917 0.229,0.219 10 false G 2.99,3.344 3.219,3.563 0.229,0.219 10 false G 2.99,2.979 3.219,3.198 0.229,0.219 10 false G 3,2.24 3.229,2.458 0.229,0.219 10 false H 3,1.885 3.229,2.104 0.229,0.219 10 false H 3,1.51 3.229,1.729 0.229,0.219 10 false H 2.99,1.167 3.219,1.385 0.229,0.219 10 false H 2.99,4.198 3.396,4.458 0.406,0.26 10 false 1 1.417,4.25 1.823,4.51 0.406,0.26 10 false 20 1.406,4.948 1.813,5.208 0.406,0.26 10 false 19 1.406,4.604 1.813,4.865 0.406,0.26 10 false 11 3,4.542 3.406,4.802 0.406,0.26 10 false 3 3,4.885 3.406,5.146 0.406,0.26 10 false 2 3.01,2.792 3.417,3.052 0.406,0.26 10 false 4 3.01,3.167 3.417,3.427 0.406,0.26 10 false 5 3,3.51 3.406,3.771 0.406,0.26 10 false 6 3.01,3.875 3.417,4.135 0.406,0.26 10 false 7 3.01,2.063 3.417,2.323 0.406,0.26 10 false 5 3.021,1.698 3.427,1.958 0.406,0.26 10 false 4 3.01,1.333 3.417,1.594 0.406,0.26 10 false 3 3,0.958 3.406,1.219 0.406,0.26 10 false 1


for LED Type Turn Signal Light


E380630E02
3.354,3 3.51,3.198 0.156,0.198 10 false E 0.115,4.208 2.052,4.552 1.938,0.344 10 false Headlight ECU Sub-assembly 2.938,3.917 4.875,4.26 1.938,0.344 10 false Headlight Unit Assembly 3.354,3.135 5.292,3.479 1.938,0.344 10 false Headlight Lens 0.635,1.333 1.667,1.656 1.031,0.323 10 false DRL/CLL+ 0.646,1.594 2.469,1.823 1.823,0.229 10 false DRL/CLL- 0.844,1.885 1.302,2.156 0.458,0.271 10 false PWM1 1.354,1.24 1.813,1.51 0.458,0.271 10 false 10 1.354,1.521 1.813,1.792 0.458,0.271 10 false 1 1.344,1.792 1.802,2.063 0.458,0.271 10 false 16 2.021,1.25 2.479,1.521 0.458,0.271 10 false 7 2.021,1.521 2.479,1.792 0.458,0.271 10 false 8 2.021,1.802 2.479,2.073 0.458,0.271 10 false 6 5.094,1.979 6.604,2.531 1.51,0.552 10 false Clearance Light/Daytime Running Light 2.427,1.271 3.406,2 0.979,0.729 10 false Electronic Light Source Control Gear B 3.75,1.271 4.729,2 0.979,0.729 10 false Electronic Light Source Control Gear A 0.115,4.063 0.271,4.26 0.156,0.198 10 false B


CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>INITIALIZATION


PROCEDURE

1.CHECK LIGHTS
a.

Check the illumination of each clearance lights and daytime running lights.


Result:
Result Proceed to
LH side clearance light and daytime running light does not illuminate A
RH side clearance light and daytime running light does not illuminate B



A

2.PERFORM ACTIVE TEST USING GTS

B

8.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > HL AutoLeveling > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Clearance Light Clearance lights OFF or ON -
Daytime Running Light Daytime running lights OFF or ON -
Body Electrical > HL AutoLeveling > Active Test
Tester Display
Clearance Light
50004 361 17
Body Electrical > HL AutoLeveling > Active Test
Tester Display
Daytime Running Light
50004 361 20
OK:

Clearance lights and daytime running lights illuminate.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HEADLIGHT UNIT ASSEMBLY LH
3.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Interchange the headlight unit assembly LH with RH and connect the connectors.

for Bulb Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY

for LED Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

4.CHECK OPERATION (CLEARANCE LIGHTS AND DAYTIME RUNNING LIGHTS)
4.CHECK OPERATION (CLEARANCE LIGHTS AND DAYTIME RUNNING LIGHTS)
a.

Check the operation of the clearance lights and daytime running lights.

OK:

The clearance lights and daytime running lights operate normally.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

5.CONFIRM MODEL
5.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Bulb Type Turn Signal Light A
for LED Type Turn Signal Light B



A

6.INSPECT HEADLIGHT UNIT ASSEMBLY LH

B

7.INSPECT HEADLIGHT UNIT ASSEMBLY LH
6.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E380638C01
1.073,0.625 1.375,0.875 0.302,0.25 3.417,0.615 3.719,0.865 0.302,0.25 5.792,0.635 6.094,0.885 0.302,0.25 1.99,2.167 1.75,1.708 false 0.521,2.167 0.688,1.698 false 1.396,2.156 1.635,1.698 false 0.333,0.583 0.646,0.781 0.313,0.198 10 false *a 2.51,0.563 2.823,0.76 0.313,0.198 10 false *b 5.094,0.573 5.406,0.771 0.313,0.198 10 false *b 1.177,0.667 1.49,0.865 0.313,0.198 10 false B 3.51,0.656 3.823,0.854 0.313,0.198 10 false G 5.896,0.677 6.208,0.875 0.313,0.198 10 false H 1.885,2.219 2.354,2.438 0.469,0.219 10 false DRL+ 0.354,2.188 0.823,2.406 0.469,0.219 10 false DRL- 1.198,2.198 1.667,2.417 0.469,0.219 10 false CLL+
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to No. 1 Headlight Clearance LED Unit LH)



b.

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-20 (DRL+) - G-1 Always Below 1 Ω
B-11 (DRL-) - G-3 Always Below 1 Ω
B-19 (CLL+) - G-2 Always Below 1 Ω
G-4 - H-5 Always Below 1 Ω
G-5 - H-4 Always Below 1 Ω
G-6 - H-3 Always Below 1 Ω
G-7 - H-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

7.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E371567C05
1.802,0.49 2.167,0.729 0.365,0.24 4.865,0.5 5.229,0.74 0.365,0.24 2.948,1.927 2.708,1.406 true 0.938,1.948 1.25,1.406 true 2.063,2.083 2.063,1.573 true 0.667,0.479 0.979,0.677 0.313,0.198 10 false *a 3.677,0.448 3.99,0.646 0.313,0.198 10 false *b 1.948,0.531 2.26,0.729 0.313,0.198 10 false B 5.01,0.552 5.323,0.75 0.313,0.198 10 false E 2.813,1.979 3.521,2.167 0.708,0.188 10 false DRL/CLL+ 0.573,1.99 1.292,2.156 0.719,0.167 10 false DRL/CLL- 1.885,2.125 2.531,2.375 0.646,0.25 10 false PWM1
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Lens LH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 (DRL/CLL+) - E-7 Always Below 1 Ω
B-1 (DRL/CLL-) - E-8 Always Below 1 Ω
B-16 (PWM1) - E-6 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

8.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling (Sub) / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Clearance Light Clearance lights OFF or ON -
Daytime Running Light Daytime running lights OFF or ON -
Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display
Clearance Light
50004 414 2
Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display
Daytime Running Light
50004 414 5
OK:

Clearance lights and daytime running lights illuminate.



Result:
Proceed to
OK
NG



OK

NG

9.CHECK HEADLIGHT UNIT ASSEMBLY RH
9.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Interchange the headlight unit assembly RH with LH and connect the connectors.

for Bulb Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY

for LED Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

10.CHECK OPERATION (CLEARANCE LIGHTS AND DAYTIME RUNNING LIGHTS)
10.CHECK OPERATION (CLEARANCE LIGHTS AND DAYTIME RUNNING LIGHTS)
a.

Check the operation of the clearance lights and daytime running lights.

OK:

The clearance lights and daytime running lights operate normally.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

11.CONFIRM MODEL
11.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Bulb Type Turn Signal Light A
for LED Type Turn Signal Light B



A

12.INSPECT HEADLIGHT UNIT ASSEMBLY RH

B

13.INSPECT HEADLIGHT UNIT ASSEMBLY RH
12.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E380638C01
1.073,0.625 1.375,0.875 0.302,0.25 3.417,0.615 3.719,0.865 0.302,0.25 5.792,0.635 6.094,0.885 0.302,0.25 1.99,2.167 1.75,1.708 false 0.521,2.167 0.688,1.698 false 1.396,2.156 1.635,1.698 false 0.333,0.583 0.646,0.781 0.313,0.198 10 false *a 2.51,0.563 2.823,0.76 0.313,0.198 10 false *b 5.094,0.573 5.406,0.771 0.313,0.198 10 false *b 1.177,0.667 1.49,0.865 0.313,0.198 10 false B 3.51,0.656 3.823,0.854 0.313,0.198 10 false G 5.896,0.677 6.208,0.875 0.313,0.198 10 false H 1.885,2.219 2.354,2.438 0.469,0.219 10 false DRL+ 0.354,2.188 0.823,2.406 0.469,0.219 10 false DRL- 1.198,2.198 1.667,2.417 0.469,0.219 10 false CLL+
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to No. 1 Headlight Clearance LED Unit RH)



b.

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-20 (DRL+) - G-1 Always Below 1 Ω
B-11 (DRL-) - G-3 Always Below 1 Ω
B-19 (CLL+) - G-2 Always Below 1 Ω
G-4 - H-5 Always Below 1 Ω
G-5 - H-4 Always Below 1 Ω
G-6 - H-3 Always Below 1 Ω
G-7 - H-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

13.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E371567C05
1.802,0.49 2.167,0.729 0.365,0.24 4.865,0.5 5.229,0.74 0.365,0.24 2.948,1.927 2.708,1.406 true 0.938,1.948 1.25,1.406 true 2.063,2.083 2.063,1.573 true 0.667,0.479 0.979,0.677 0.313,0.198 10 false *a 3.677,0.448 3.99,0.646 0.313,0.198 10 false *b 1.948,0.531 2.26,0.729 0.313,0.198 10 false B 5.01,0.552 5.323,0.75 0.313,0.198 10 false E 2.813,1.979 3.521,2.167 0.708,0.188 10 false DRL/CLL+ 0.573,1.99 1.292,2.156 0.719,0.167 10 false DRL/CLL- 1.885,2.125 2.531,2.375 0.646,0.25 10 false PWM1
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Lens RH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 (DRL/CLL+) - E-7 Always Below 1 Ω
B-1 (DRL/CLL-) - E-8 Always Below 1 Ω
B-16 (PWM1) - E-6 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG