Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › from 2019.10
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0344647 SFI SYSTEM(w/o Canister Pump Module) J

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E66
0.99,0.833 2.802,1.135 1.813,0.302 10 false from EFI-MAIN NO. 4 Fuse 0.938,1.177 2.698,1.531 1.76,0.354 10 false from EFI-MAIN NO. 1 Relay 0.135,1.969 2.625,2.469 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.563,3.031 2.427,0.385 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.885,0.677 3.563,1 0.677,0.323 10 false BATT 2.823,1.042 3.49,1.292 0.667,0.25 10 false +B, +B2 3.063,2.021 3.427,2.25 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>ECM Power Source Circuit

·

VC Output Circuit

A453194E01
0.552,0.729 2.063,1.198 1.51,0.469 10 false Throttle Body with Motor Assembly 0.552,0.552 2.063,1.021 1.51,0.469 10 false C27 0.531,1.979 2.042,2.448 1.51,0.469 10 false d5 0.531,2.146 2.271,2.635 1.74,0.49 10 false Crankshaft Position Sensor 0.531,3.385 2.167,3.896 1.635,0.51 10 false Camshaft Position Sensor (for Intake Camshaft) 0.542,3.219 2.052,3.688 1.51,0.469 10 false C18 0.531,4.708 2.167,5.219 1.635,0.51 10 false Camshaft Position Sensor (for Exhaust Camshaft) 0.542,4.542 2.052,5.01 1.51,0.469 10 false C77 0.552,6.042 2.26,6.563 1.708,0.521 10 false Manifold Absolute Pressure Sensor 0.552,5.875 2.063,6.344 1.51,0.469 10 false C28 0.51,7.365 1.813,8.083 1.302,0.719 10 false Oil Pressure Sensor (Oil Pressure and Temperature Sensor) 0.5,7.177 2.01,7.646 1.51,0.469 10 false C110 6.281,0.177 6.677,0.521 0.396,0.344 10 false 5 V 2.531,0.417 2.927,0.76 0.396,0.344 10 false VC 2.552,0.781 2.948,1.125 0.396,0.344 10 false E2 2.458,1.146 2.854,1.49 0.396,0.344 10 false VTA 2.417,1.51 2.813,1.854 0.396,0.344 10 false VTA2 2.365,2.031 2.76,2.375 0.396,0.344 10 false VCNE 2.49,2.385 2.885,2.729 0.396,0.344 10 false NE- 2.479,2.76 2.875,3.104 0.396,0.344 10 false NE+ 2.542,3.313 2.938,3.656 0.396,0.344 10 false VC 2.448,3.656 2.844,4 0.396,0.344 10 false VVI- 2.448,4.031 2.844,4.375 0.396,0.344 10 false VVI+ 2.479,4.625 2.875,4.969 0.396,0.344 10 false VC2 2.406,4.969 2.802,5.313 0.396,0.344 10 false VVE- 2.385,5.344 2.781,5.688 0.396,0.344 10 false VVE+ 2.531,5.885 2.927,6.229 0.396,0.344 10 false VC 2.51,6.625 2.906,6.969 0.396,0.344 10 false PIM 2.563,6.25 2.958,6.594 0.396,0.344 10 false E2 2.552,7.208 2.948,7.552 0.396,0.344 10 false VC 2.365,7.948 2.875,8.25 0.51,0.302 10 false POUT 2.448,7.573 2.844,7.917 0.396,0.344 10 false GND 2.865,0.302 3.26,0.646 0.396,0.344 10 false 2 2.865,0.656 3.26,1 0.396,0.344 10 false 4 2.854,1.031 3.25,1.375 0.396,0.344 10 false 1 2.854,1.385 3.25,1.729 0.396,0.344 10 false 3 2.854,1.906 3.25,2.25 0.396,0.344 10 false 3 2.854,2.271 3.25,2.615 0.396,0.344 10 false 2 2.854,2.635 3.25,2.979 0.396,0.344 10 false 1 2.854,3.188 3.25,3.531 0.396,0.344 10 false 3 2.854,3.552 3.25,3.896 0.396,0.344 10 false 2 2.844,3.906 3.24,4.25 0.396,0.344 10 false 1 2.854,4.49 3.25,4.833 0.396,0.344 10 false 3 2.854,4.865 3.25,5.208 0.396,0.344 10 false 2 2.854,5.219 3.25,5.563 0.396,0.344 10 false 1 2.854,5.76 3.25,6.104 0.396,0.344 10 false 3 2.844,6.135 3.24,6.479 0.396,0.344 10 false 1 2.854,6.49 3.25,6.833 0.396,0.344 10 false 2 2.844,7.104 3.24,7.448 0.396,0.344 10 false 3 2.844,7.833 3.24,8.177 0.396,0.344 10 false 1 2.854,7.469 3.25,7.813 0.396,0.344 10 false 2 4.885,0.417 5.281,0.76 0.396,0.344 10 false C57 4.885,0.781 5.281,1.125 0.396,0.344 10 false C57 4.885,1.146 5.281,1.49 0.396,0.344 10 false C57 4.885,1.51 5.281,1.854 0.396,0.344 10 false C57 4.885,2.021 5.281,2.365 0.396,0.344 10 false C57 4.896,2.385 5.292,2.729 0.396,0.344 10 false C57 4.885,2.76 5.281,3.104 0.396,0.344 10 false C57 4.885,3.292 5.281,3.635 0.396,0.344 10 false C57 4.885,3.667 5.281,4.01 0.396,0.344 10 false C57 4.885,4.031 5.281,4.375 0.396,0.344 10 false C57 4.875,4.625 5.271,4.969 0.396,0.344 10 false C57 4.885,5.885 5.281,6.229 0.396,0.344 10 false C57 4.896,4.99 5.292,5.333 0.396,0.344 10 false C57 4.875,5.344 5.271,5.688 0.396,0.344 10 false C57 4.885,6.25 5.281,6.594 0.396,0.344 10 false C57 4.896,6.615 5.292,6.958 0.396,0.344 10 false C57 4.885,7.219 5.281,7.563 0.396,0.344 10 false C57 4.896,7.583 5.292,7.927 0.396,0.344 10 false C57 4.885,7.948 5.281,8.292 0.396,0.344 10 false C57 4.896,0.219 5.292,0.563 0.396,0.344 10 false 109 4.896,0.594 5.292,0.938 0.396,0.344 10 false 110 4.896,0.969 5.292,1.313 0.396,0.344 10 false 108 4.938,1.323 5.333,1.667 0.396,0.344 10 false 87 4.896,1.833 5.292,2.177 0.396,0.344 10 false 116 4.896,2.208 5.292,2.552 0.396,0.344 10 false 115 4.938,2.573 5.333,2.917 0.396,0.344 10 false 93 4.938,3.104 5.333,3.448 0.396,0.344 10 false 88 4.938,3.49 5.333,3.833 0.396,0.344 10 false 89 4.938,3.844 5.333,4.188 0.396,0.344 10 false 90 4.896,4.427 5.292,4.771 0.396,0.344 10 false 113 4.896,4.802 5.292,5.146 0.396,0.344 10 false 114 4.938,5.167 5.333,5.51 0.396,0.344 10 false 91 4.896,5.698 5.292,6.042 0.396,0.344 10 false 121 4.885,6.073 5.281,6.417 0.396,0.344 10 false 119 4.896,6.438 5.292,6.781 0.396,0.344 10 false 120 4.938,7.031 5.333,7.375 0.396,0.344 10 false 99 4.896,7.396 5.292,7.74 0.396,0.344 10 false 100 4.896,7.771 5.292,8.115 0.396,0.344 10 false 122 5.281,0.313 5.677,0.656 0.396,0.344 10 false VCTA 5.292,0.677 5.688,1.021 0.396,0.344 10 false ETA 5.292,1.146 5.688,1.49 0.396,0.344 10 false VTA1 5.302,1.51 5.698,1.854 0.396,0.344 10 false VTA2 5.281,1.917 5.677,2.26 0.396,0.344 10 false VCNE 5.281,2.281 5.677,2.625 0.396,0.344 10 false NE- 5.292,2.74 5.688,3.083 0.396,0.344 10 false NE+ 5.281,3.188 5.677,3.531 0.396,0.344 10 false VCV1 5.292,3.552 5.688,3.896 0.396,0.344 10 false VV1- 5.292,4.031 5.688,4.375 0.396,0.344 10 false VV1+ 5.292,4.5 5.688,4.844 0.396,0.344 10 false VCE1 5.302,4.865 5.698,5.208 0.396,0.344 10 false EV1- 5.292,5.344 5.688,5.688 0.396,0.344 10 false EV1+ 5.292,5.781 5.927,6.125 0.635,0.344 10 false VCPM 5.292,6.625 5.688,6.969 0.396,0.344 10 false PIM 5.292,6.146 5.688,6.49 0.396,0.344 10 false EPIM 5.292,7.104 5.906,7.469 0.615,0.365 10 false VCPE 5.302,7.948 5.698,8.292 0.396,0.344 10 false PEO 5.302,7.479 5.823,7.771 0.521,0.292 10 false EPEO 5.74,8.646 6.146,8.833 0.406,0.188 10 false ECM 2.385,8.292 2.885,8.615 0.5,0.323 10 false TOUT 2.854,8.177 3.25,8.521 0.396,0.344 10 false 4 4.885,8.292 5.281,8.635 0.396,0.344 10 false C57 4.885,8.125 5.281,8.469 0.396,0.344 10 false 123 5.292,8.281 5.844,8.625 0.552,0.344 10 false THEO

A414183E05
5.813,8.208 6.24,8.448 0.427,0.24 10 false ECM 0.188,8.198 0.615,8.438 0.427,0.24 10 false F12 0.563,8.208 3.76,8.594 3.198,0.385 10 false Fuel Pressure Sensor (Fuel Delivery Pipe with Sensor Assembly) (for Low Pressure Side) 0.552,5.708 0.979,5.948 0.427,0.24 10 false d3 0.542,5.885 2.125,6.344 1.583,0.458 10 false Fuel Pressure Sensor (for High Pressure Side) 0.542,4.01 1.854,4.427 1.313,0.417 10 false Mass Air Flow Meter Sub-assembly 0.542,3.833 0.969,4.073 0.427,0.24 10 false C30 0.51,0.677 0.938,0.917 0.427,0.24 10 false A20 0.51,0.833 2.104,1.417 1.594,0.583 10 false Accelerator Pedal Sensor Assembly 2.354,0.604 2.781,0.844 0.427,0.24 10 false VCPA 2.469,1.604 2.896,1.844 0.427,0.24 10 false EPA 2.458,2.604 2.885,2.844 0.427,0.24 10 false VPA 2.865,0.5 3.292,0.74 0.427,0.24 10 false 4 2.865,1.01 3.292,1.25 0.427,0.24 10 false 1 2.854,1.521 3.281,1.76 0.427,0.24 10 false 5 2.875,2.01 3.302,2.25 0.427,0.24 10 false 2 2.865,2.51 3.292,2.75 0.427,0.24 10 false 6 2.875,3.01 3.302,3.25 0.427,0.24 10 false 3 4.927,0.604 5.354,0.844 0.427,0.24 10 false A24 4.917,3.771 5.344,4.01 0.427,0.24 10 false C57 4.948,0.406 5.375,0.646 0.427,0.24 10 false 57 4.948,0.917 5.375,1.156 0.427,0.24 10 false 60 4.969,1.406 5.396,1.646 0.427,0.24 10 false 56 4.958,1.927 5.385,2.167 0.427,0.24 10 false 59 4.969,2.427 5.396,2.667 0.427,0.24 10 false 55 4.969,2.917 5.396,3.156 0.427,0.24 10 false 58 4.958,3.573 5.385,3.813 0.427,0.24 10 false 78 4.948,4 5.375,4.24 0.427,0.24 10 false 79 4.917,4.406 5.344,4.646 0.427,0.24 10 false 101 4.917,4.823 5.344,5.063 0.427,0.24 10 false 102 4.938,5.479 5.365,5.719 0.427,0.24 10 false 98 4.958,5.906 5.385,6.146 0.427,0.24 10 false 96 4.948,6.292 5.375,6.531 0.427,0.24 10 false 97 4.958,6.927 5.385,7.167 0.427,0.24 10 false 84 4.958,7.323 5.385,7.563 0.427,0.24 10 false 61 4.927,7.719 5.354,7.958 0.427,0.24 10 false 107 2.552,3.771 2.979,4.01 0.427,0.24 10 false 5V 2.479,4.198 2.906,4.438 0.427,0.24 10 false E2G 2.552,4.604 2.979,4.844 0.427,0.24 10 false FG 2.479,5.031 2.906,5.271 0.427,0.24 10 false THA 2.573,5.698 3.135,5.927 0.563,0.229 10 false VC 2.583,6.073 3.01,6.313 0.427,0.24 10 false E2 2.573,6.469 3,6.708 0.427,0.24 10 false PR 2.5,7.896 2.927,8.135 0.427,0.24 10 false PEL 5.313,3.667 5.771,3.896 0.458,0.229 10 false VCVG 5.313,5.583 5.74,5.823 0.427,0.24 10 false VCPR 5.323,7.021 5.75,7.26 0.427,0.24 10 false VCPF 2.385,1.104 2.813,1.344 0.427,0.24 10 false VCP2 2.375,2.104 2.802,2.344 0.427,0.24 10 false EPA2 2.385,3.104 2.813,3.344 0.427,0.24 10 false VPA2 2.563,7.135 2.99,7.375 0.427,0.24 10 false VC 2.573,7.51 3,7.75 0.427,0.24 10 false E2 2.885,4.49 3.313,4.729 0.427,0.24 10 false 1 2.885,5.552 3.313,5.792 0.427,0.24 10 false 1 2.885,6.99 3.313,7.229 0.427,0.24 10 false 1 2.885,4.094 3.313,4.333 0.427,0.24 10 false 2 2.896,5.948 3.323,6.188 0.427,0.24 10 false 2 2.896,7.823 3.323,8.063 0.427,0.24 10 false 2 2.875,3.677 3.302,3.917 0.427,0.24 10 false 3 2.896,6.344 3.323,6.583 0.427,0.24 10 false 3 2.906,7.396 3.333,7.635 0.427,0.24 10 false 3 2.896,4.917 3.323,5.156 0.427,0.24 10 false 4 5.302,0.521 5.729,0.76 0.427,0.24 10 false VCPA 5.302,1.021 5.729,1.26 0.427,0.24 10 false VCP2 5.313,1.51 5.74,1.75 0.427,0.24 10 false EPA 5.302,2.01 5.729,2.25 0.427,0.24 10 false EPA2 5.313,2.625 5.74,2.865 0.427,0.24 10 false VPA 5.313,3.115 5.74,3.354 0.427,0.24 10 false VPA2 5.313,4.083 5.74,4.323 0.427,0.24 10 false E2G 5.323,4.604 5.75,4.844 0.427,0.24 10 false VG 5.313,5.042 5.74,5.281 0.427,0.24 10 false THA 5.323,5.969 5.75,6.208 0.427,0.24 10 false EPR 5.313,6.448 5.74,6.688 0.427,0.24 10 false PR 5.313,7.885 5.74,8.125 0.427,0.24 10 false PFL 5.323,7.417 5.75,7.656 0.427,0.24 10 false EPFL 4.927,1.115 5.354,1.354 0.427,0.24 10 false A24 4.938,1.604 5.365,1.844 0.427,0.24 10 false A24 4.938,2.115 5.365,2.354 0.427,0.24 10 false A24 4.927,2.615 5.354,2.854 0.427,0.24 10 false A24 4.927,3.115 5.354,3.354 0.427,0.24 10 false A24 4.927,4.177 5.354,4.417 0.427,0.24 10 false C57 4.917,4.615 5.344,4.854 0.427,0.24 10 false C57 4.927,5.031 5.354,5.271 0.427,0.24 10 false C57 4.927,5.688 5.354,5.927 0.427,0.24 10 false C57 4.917,6.083 5.344,6.323 0.427,0.24 10 false C57 4.927,6.458 5.354,6.698 0.427,0.24 10 false C57 4.938,7.135 5.365,7.375 0.427,0.24 10 false C57 4.938,7.531 5.365,7.771 0.427,0.24 10 false C57 4.938,7.927 5.365,8.167 0.427,0.24 10 false C57


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK EFI NO. 1 FUSE VOLTAGE

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK EFI NO. 1 FUSE VOLTAGE
A402426C04
2.083,0.76 2.698,0.292 true 0.156,0.208 0.469,0.406 0.313,0.198 10 false *1 2.729,0.188 3.042,0.385 0.313,0.198 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EFI NO. 1 Fuse


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI NO. 1 fuse) - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Check the fuse with it installed to the engine room relay block and junction block assembly.

·

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)

B

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

5.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

B

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

7.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

8.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK CONNECTION BETWEEN GTS AND ECM (OIL PRESSURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

9.CHECK CONNECTION BETWEEN GTS AND ECM (OIL PRESSURE SENSOR)
a.

Disconnect the oil pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))

B

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))
a.

Disconnect the fuel pressure sensor (for high pressure side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



A

11.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY) (FOR LOW PRESSURE SIDE))

B

REPLACE FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

11.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY) (FOR LOW PRESSURE SIDE))
a.

Disconnect the fuel pressure sensor (fuel delivery pipe with sensor assembly) (for low pressure side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor assembly) (for low pressure side).

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



A

12.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)

B

REPLACE FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY) (FOR LOW PRESSURE SIDE)

12.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



A

13.CHECK HARNESS AND CONNECTOR

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

13.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the crankshaft position sensor connector.


c.

Disconnect the camshaft position sensor (for intake camshaft) connector.


d.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


e.

Disconnect the manifold absolute pressure sensor connector.


f.

Disconnect the oil pressure sensor connector.


g.

Disconnect the accelerator pedal sensor assembly connector.


h.

Disconnect the mass air flow meter sub-assembly connector.


i.

Disconnect the fuel pressure sensor (for high pressure side) connector.


j.

Disconnect the fuel pressure sensor (fuel delivery pipe with sensor assembly) (for low pressure side) connector.


k.

Disconnect the ECM connectors.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C57-109 (VCTA) - Body ground Always 10 kΩ or higher
C57-116 (VCNE) - Body ground Always 10 kΩ or higher
C57-88 (VCV1) - Body ground Always 10 kΩ or higher
C57-113 (VCE1) - Body ground Always 10 kΩ or higher
C57-121 (VCPM) - Body ground Always 10 kΩ or higher
C57-99 (VCPE) - Body ground Always 10 kΩ or higher
A24-57 (VCPA) - Body ground Always 10 kΩ or higher
A24-60 (VCP2) - Body ground Always 10 kΩ or higher
C57-78 (VCVG) - Body ground Always 10 kΩ or higher
C57-98 (VCPR) - Body ground Always 10 kΩ or higher
C57-84 (VCPF) - Body ground Always 10 kΩ or higher



m.

Measure the resistance according to the value(s) in the table below.

HINT:

Remove the VVT, EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays connected between the checked terminals as the coil inside the relay influences the measurement value.


Standard Resistance:
Tester Connection Condition Specified Condition
A24-9 (+B) - 1 (EFI NO. 1 fuse) Always Below 1 Ω
A24-35 (+B2) - 1 (EFI NO. 1 fuse) Always Below 1 Ω
A24-9 (+B) - Body ground Always 10 kΩ or higher
A24-35 (+B2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR