Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › from 2019.10
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0329531 LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System) C

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System)  B2452  Abnormal Height Sensor Data at Initialization  


DESCRIPTION

The headlight ECU sub-assembly LH stores this DTC if the value from the rear height control sensor sub-assembly LH is out of range when performing initialization of the headlight ECU sub-assembly LH, such as when the vehicle is not level or jacked up.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2452 Abnormal Height Sensor Data at Initialization
Detection condition:

The ignition switch is ON.


Malfunction status:

Abnormal rear height control sensor sub-assembly LH value detected during initialization


Malfunction duration:

-


·

Vehicle condition when initializing

·

Rear height control sensor sub-assembly LH

·

Harness or connector

·

Headlight ECU sub-assembly LH


HL AutoLeveling

WIRING DIAGRAM

E370854E60
4.208,2.313 6.531,2.719 2.323,0.406 10 false Headlight ECU Sub-assembly LH 4.208,2.177 4.5,2.427 0.292,0.25 10 false A83 2.854,1.51 3.146,1.76 0.292,0.25 10 false 1 2.844,0.99 3.135,1.24 0.292,0.25 10 false 2 2.833,0.479 3.125,0.729 0.292,0.25 10 false 3 4.958,0.302 5.25,0.552 0.292,0.25 10 false 5 V 2.406,0.573 2.74,0.823 0.333,0.25 10 false SHB 2.344,1.094 2.844,1.385 0.5,0.292 10 false SHRR 2.406,1.615 2.802,1.865 0.396,0.25 10 false SHG 1.083,2.156 1.375,2.406 0.292,0.25 10 false U1 1.083,2.313 2.792,2.76 1.708,0.448 10 false Rear Height Control Sensor Sub-assembly LH 4.094,1.5 4.385,1.75 0.292,0.25 10 false 15 4.344,1.521 4.729,1.771 0.385,0.25 10 false SGR 4.344,0.99 4.771,1.26 0.427,0.271 10 false SHRL 4.104,1 4.396,1.25 0.292,0.25 10 false 17 4.104,0.5 4.396,0.75 0.292,0.25 10 false 16 4.354,0.5 4.719,0.74 0.365,0.24 10 false SBR

CAUTION / NOTICE / HINT

NOTICE:
·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>INITIALIZATION

·

If any of the following are performed, it is necessary to initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>INITIALIZATION

-

Replacement of the rear height control sensor sub-assembly LH

-

Removal/installation of the rear height control sensor sub-assembly LH

-

Work that changes the vehicle height such as replacement of suspension components




PROCEDURE

1.INITIALIZATION HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.


e.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
OK:

DTC B2452 is not output.



Result:
Proceed to
OK
NG



OK

END (INITIALIZATION WAS NOT COMPLETED)

NG

4.CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
4.CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
a.

Check the installation condition of the rear height control sensor sub-assembly LH.

OK:

Rear height control sensor sub-assembly LH is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

NG

5.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
a.

Remove the rear height control sensor sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL


b.

Inspect the rear height control sensor sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY LH)

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

6.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Disconnect the A83 headlight ECU sub-assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U1-3 (SHB) - A83-16 (SBR) Always Below 1 Ω
U1-2 (SHRR) - A83-17 (SHRL) Always Below 1 Ω
U1-1 (SHG) - A83-15 (SGR) Always Below 1 Ω
U1-3 (SHB) or A83-16 (SBR) - Body ground Always 10 kΩ or higher
U1-2 (SHRR) or A83-17 (SHRL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR