Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › CYLINDER HEAD › 2019.10–2021.02
RM33A0E _51 Engine / Hybrid System _065342 A25A-FKS ENGINE MECHANICAL _0319523 CYLINDER HEAD A

A25A-FKS ENGINE MECHANICAL  CYLINDER HEAD  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
Replacement of automatic transaxle assembly
1.

Reset memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for UB80E Initialization
(Click here)for UB80E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of front bumper assembly Front television camera view adjustment Panoramic view monitor system (Click here)for Initialization
(Click here)for Calibration
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 13711 1.REMOVE INTAKE VALVE

a.
A400439N01
0.958,0.448 1.25,0.115 1.25,0.115 1.406,0.115 true 2.25,1.844 2.01,2.042 2.01,2.042 1.865,2.042 false 1.469,0.021 1.927,0.219 0.458,0.198 10 false SST 1.563,1.958 2.021,2.156 0.458,0.198 10 false SST

Using SST, compress each compression spring and remove the 8 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 8 valve spring retainers, 8 compression springs and 8 intake valves from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13715 2.REMOVE EXHAUST VALVE

a.
A400441N01
1.375,1.875 1.583,1.99 1.583,1.99 1.75,1.99 false 1.781,0.135 1.99,0.135 1.99,0.135 2.313,0.26 true 1.823,1.927 2.281,2.125 0.458,0.198 10 false SST 1.406,0.063 1.75,0.281 0.344,0.219 10 true SST

Using SST, compress each compression spring and remove the 8 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 8 valve spring retainers, 8 compression springs and 8 exhaust valves from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 3.REMOVE VALVE STEM OIL SEAL

a.
A400443

Using needle-nose pliers, remove the 16 valve stem oil seals.


Hide 4.REMOVE VALVE SPRING SEAT

a.
A400444

Using compressed air and a Magnet Hand, remove the 16 valve spring seats from the cylinder head sub-assembly by blowing air onto them.


Hide 11117E 5.REMOVE NO. 1 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a No. 1 straight screw plug or a plug is corroded, replace it.


A400445

a.

Using a 6 mm straight hexagon wrench, remove the 4 No. 1 straight screw plugs from the cylinder head sub-assembly.


Hide 6.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A400447

Using an E8 "TORX" socket wrench, remove the 7 stud bolts.