The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during automatic transaxle assembly removal/installation are shown below.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
| *a | An Object Exceeding Weight Limit of Transmission Jack |
The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.
1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
11361J
2.REMOVE FLYWHEEL HOUSING UNDER COVER
32101A
3.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.
There will be one black colored drive plate and torque converter assembly setting bolt.
4.DISCONNECT VACUUM HOSE
Disconnect the vacuum hose from the rear engine mounting insulator.
Disconnect the vacuum hose from the vacuum hose connector.
Disengage the 9 clamps to disconnect the vacuum hose from the automatic transaxle assembly.
16261G
5.REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)
16260
6.DISCONNECT WATER BY-PASS HOSE ASSEMBLY
Slide the clip and disconnect the water by-pass hose assembly from the transmission oil cooler.
Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.
35104V
7.REMOVE BREATHER PLUG HOSE
Disengage the 2 hose clamps to disconnect the breather plug hose.
Using a screwdriver with its tip wrapped with protective tape, remove the breather plug hose from the No. 1 breather plug (ATM).
Be careful not to damage the No. 1 breather plug (ATM).
| *1 | Breather Plug Sub-assembly |
| *2 | Breather Plug Hose |
Remove the breather plug sub-assembly from the breather plug hose.
Be careful not to damage the breather plug sub-assembly.
45319
8.REMOVE STEERING GEAR HEAT INSULATOR
9.DISCONNECT WIRE HARNESS
Disengage the claw, rotate the lever and disconnect the transmission wire connector.
Disconnect the park/neutral position switch assembly connector.
Disengage the wire harness clamp and disconnect the vacuum switching valve (for active control engine mount system) connector.
Disconnect the rack and pinion power steering gear assembly connector.
Release the lock before rotating the lock lever.
Remove the 2 bolts to disconnect the wire harness from the rack and pinion power steering gear assembly.
Remove the bolt.
Disengage the 9 wire harness clamps to disconnect the wire harness.
Remove the 2 bolts.
Disengage the wire harness clamp to disconnect the wire harness from the automatic transaxle assembly.
23825
10.REMOVE FUEL DELIVERY GUARD
11.INSTALL ENGINE HANGERS
51100G
12.REMOVE FRONT FRAME ASSEMBLY
12311A
13.REMOVE FRONT ENGINE MOUNTING BRACKET
Remove the 3 bolts and front engine mounting bracket from the transaxle housing.
11363A
14.REMOVE FLYWHEEL HOUSING SIDE COVER
28100
15.REMOVE STARTER ASSEMBLY
Disconnect the starter assembly connector.
Open the terminal cap.
Remove the nut and disconnect the No. 2 engine wire from terminal 30.
Remove the 2 bolts and starter assembly from the cylinder block sub-assembly.
30500
16.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY
Support the automatic transaxle assembly with a transmission jack.
Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.
Remove the 8 bolts and automatic transaxle assembly.
To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.
12372A
17.REMOVE ENGINE MOUNTING INSULATOR LH
Remove the 5 bolts and engine mounting insulator LH from the automatic transaxle case sub-assembly.
12371A
18.REMOVE REAR ENGINE MOUNTING INSULATOR
12303
19.REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY
Remove the 4 bolts and rear engine mounting bracket sub-assembly from the transaxle housing.
32942
20.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE
32941
21.DISCONNECT INLET NO. 1 OIL COOLER HOSE
32907C
22.REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE
Remove the 2 bolts to disconnect the No. 1 oil cooler tube sub-assembly without hose from the automatic transaxle case sub-assembly.
Slide the clip and disconnect the inlet No. 2 oil cooler hose from the transmission oil cooler.
Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 2 oil cooler hose and transmission oil cooler.
Slide the clip and disconnect the outlet No. 2 oil cooler hose to remove the No. 1 oil cooler tube sub-assembly without hose from the transmission oil cooler.
Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 2 oil cooler hose and transmission oil cooler.
33493A
23.REMOVE TRANSMISSION OIL COOLER
33823
24.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle case sub-assembly.
35150
25.REMOVE TRANSMISSION CASE PLUG ASSEMBLY
Remove the transmission case plug assembly from the transaxle housing.
Remove the O-ring from the transmission case plug assembly.
26.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the bolt and wire harness clamp bracket from the automatic transaxle case sub-assembly.
Remove the bolt and wire harness clamp bracket from the automatic transaxle case sub-assembly.
Remove the 4 bolts and 4 wire harness clamp brackets from the automatic transaxle case sub-assembly and transmission case side cover.
32000
27.REMOVE TORQUE CONVERTER ASSEMBLY
Remove the torque converter assembly from the automatic transaxle assembly.
32000
28.INSPECT TORQUE CONVERTER ASSEMBLY
32101
29.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY