Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › from 2019.10
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0328248 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P012800  Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)  P012807  Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) Mechanical Failure  


DESCRIPTION

The ECM uses the engine coolant temperature sensor, installed to the water outlet, to monitor the operation of the thermostat.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P012800 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) All of the following conditions are met for 5 seconds or more (2 trip detection logic):
1.

Cold start.

2.

The engine is warmed up.

3.

The engine coolant temperature is less than 75°C (167°F).


·

Water inlet with thermostat sub-assembly

·

Engine cooling system

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored SAE Code: P0128
P012807 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) Mechanical Failure All of the following conditions are met for 3 times (2 trip detection logic):
1.

The engine coolant temperature is less than 75°C (167°F).

2.

The value of the change in engine coolant temperature is less than the threshold.


·

Water inlet with thermostat sub-assembly

·

Engine cooling system

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored SAE Code: P0128

MONITOR DESCRIPTION

P012800: Judgement by Simulated Engine Coolant Temperature
A121605E49
4.865,2.333 5.146,2.646 false 3.844,2.083 3.729,0.885 3.729,0.885 3.594,0.885 false 4.458,2.656 6,3.063 1.542,0.406 10 false Indicated Engine Coolant Temperature Reading 3.104,3.667 5.344,3.875 2.24,0.208 10 false DTC Stored (after 2 Driving Cycles) 2.25,0.813 3.583,1.208 1.333,0.396 10 false Estimated Engine Coolant Temperature 1.073,1.656 1.688,2.125 0.615,0.469 10 false Threshold (75°C) 4.281,1.01 4.969,1.177 0.688,0.167 10 false 5 seconds 1.083,2.771 2.104,3.125 1.021,0.354 10 false Engine Coolant Temperature 2.292,3.292 2.635,3.5 0.344,0.208 10 false Time

The ECM estimates the engine coolant temperature based on the starting temperature, engine loads, and engine speeds. The ECM then compares the estimated temperature with the actual engine coolant temperature. When the estimated engine coolant temperature reaches 75°C (167°F), the ECM checks the actual engine coolant temperature. If the actual engine coolant temperature is less than 75°C (167°F), the ECM interprets this as a malfunction in the thermostat or the engine cooling system and stores the DTC.


P012807: Judgement by Engine Coolant Temperature Change at High Vehicle Speed
A421324E04
4.146,5.573 4.5,5.573 4.5,5.573 4.677,5.365 false 2.875,3.667 3.146,3.667 3.146,3.667 3.406,4.177 false 4.104,0.5 4.26,0.729 4.26,0.729 4.479,0.729 true 3.844,3.688 4,3.917 4,3.917 4.219,3.917 false 5.229,2 5.354,1.302 5.354,1.302 5.573,1.302 false 3.823,4.938 4.021,4.938 4.021,4.938 4.156,4.708 false 1.823,2.875 2.094,2.875 2.094,2.875 2.323,2.177 false 3.688,1.521 4,1.698 0.313,0.177 10 true Fail 4.344,1.865 4.823,2.063 0.479,0.198 10 true Fail 5.656,2.042 6.135,2.24 0.479,0.198 10 true Fail 5.26,5.219 5.563,5.417 0.302,0.198 10 true Fail 1.938,0.031 2.417,0.229 0.479,0.198 10 false 13 Sec 2.583,0.042 3.063,0.24 0.479,0.198 10 false 13 Sec 3.25,0.042 3.729,0.24 0.479,0.198 10 false 13 Sec 3.906,0.052 4.385,0.25 0.479,0.198 10 false 13 Sec 4.542,0.052 5.021,0.25 0.479,0.198 10 false 13 Sec 5.188,0.042 5.667,0.24 0.479,0.198 10 false 13 Sec 5.833,0.063 6.313,0.26 0.479,0.198 10 false 13 Sec 3.927,3.135 4.406,3.333 0.479,0.198 10 false 13 Sec 6.479,0.156 6.958,0.354 0.479,0.198 10 false Time 1.104,3.583 2.844,4.094 1.74,0.51 10 false Engine Coolant Temperature Change Value 0.552,5.49 4.063,5.781 3.51,0.292 10 true Engine coolant temperature change judgment performed 6.198,4.948 6.865,5.458 0.667,0.51 10 false Threshold Value 5.052,2.708 6.708,3.146 1.656,0.438 10 false DTC Stored (after 2 Driving Cycles) 4.531,0.656 5.698,0.979 1.167,0.323 10 true Normal Thermostat 5.625,1.229 7.135,1.542 1.51,0.313 10 true Stuck Open Thermostat 0.063,2.781 1.802,3.292 1.74,0.51 10 false Engine Coolant Temperature Change Value 4.302,3.844 6.198,4.146 1.896,0.302 10 true Normal Thermostat 2.333,4.854 3.813,5.104 1.479,0.25 10 true Stuck Open Thermostat

When the vehicle is being driven between 65 and 128 km/h (40.625 and 80 mph) and the monitoring conditions are met, the change in engine coolant temperature is monitored. The amount of change is judged to be normal or abnormal every 13 seconds, in order to monitor the thermostat operation. If the engine coolant temperature changes more than the threshold, the thermostat is judged as normal, but if it changes less than the threshold, the thermostat is judged to be malfunctioning. If an abnormal judgement is made 3 times, the ECM will illuminate the MIL and store a DTC.


MONITOR STRATEGY

Frequency of Operation Once per driving cycle: Judgement by simulated engine coolant temperature
Continuous: Judgement by engine coolant temperature change at high vehicle speed

CONFIRMATION DRIVING PATTERN

A421380E02
0.135,0.25 1.479,0.563 1.344,0.313 10 false Vehicle Speed 2.625,2.708 3.969,3.021 1.344,0.313 10 false 20 minutes 0.073,0.969 1.417,1.281 1.344,0.313 10 false 90 km/h or more 0.073,1.24 1.417,1.552 1.344,0.313 10 false 80 km/h or more 0.188,2.281 1.094,2.75 0.906,0.469 10 false Engine Switch on (IG) 1.604,2.135 2.135,2.563 0.531,0.427 10 false [A] 2.813,1.104 3.344,1.531 0.531,0.427 10 false [B] 3.656,3.021 4.188,3.448 0.531,0.427 10 false [C] 5.51,0.844 6.042,1.271 0.531,0.427 10 false [F] 6.49,3.021 6.969,3.438 0.479,0.417 10 false [G] 5.323,2.708 6.667,3.021 1.344,0.313 10 false 20 minutes 3.948,2.354 4.479,2.781 0.531,0.427 10 false [D] 4.302,2.135 4.833,2.563 0.531,0.427 10 false [E] 6.771,2.625 7.104,2.917 0.333,0.292 10 false Time 0.719,2 2.063,2.313 1.344,0.313 10 false Idling

1.

Stop the engine and allow it to soak.

2.

Connect the GTS to the DLC3.

3.

Turn the engine switch on (IG) [A].

4.

Turn the GTS on.

5.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature and Intake Air Temperature.

6.

Check that the value of the Data List item Coolant Temperature is 56°C (133°F) or less and the value of the Data List item Intake Air Temperature is between 0 and 35°C (32 and 95°F).

7.

Set the heater control to MAX HOT with fresh air mode selected and turn the A/C off.

8.

Start the engine and drive the vehicle at 80 km/h (50 mph) or more for 20 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

After the value of the Data List item Coolant Temperature stabilizes, check that it is 75°C (167°F) or higher.

HINT:

If the value of the Data List item Coolant Temperature is less than 75°C (167°F) while driving the vehicle at 80 km/h (50 mph), inspect the cooling system and thermostat.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P012800 or P012807.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, If the judgment result is INCOMPLETE, perform steps [D] through [G].



15.

With the engine stopped, leave the vehicle outside overnight [D].

16.

Turn the engine switch on (IG) [E].

17.

Turn the GTS on.

18.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.

19.

Check that the value of the Data List item Coolant Temperature is 25°C (77°F) or less.

20.

Start the engine and drive the vehicle at 90 km/h (56 mph) or more for 20 minutes [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


21.

Enter the following menus: Powertrain / Engine / Trouble Codes [G].

22.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



23.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

24.

Input the DTC: P012800 or P012807.

25.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

When this DTC is output, check the engine coolant temperature using the GTS. Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature. If the value of Coolant Temperature is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and their connection condition) between the ECM and the engine coolant temperature sensor first.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P012800 OR P012807)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P012800 or P012807 is output A
DTC P012800 or P012807 and other DTCs are output B


HINT:

If any DTCs other than P012800 or P012807 are output, troubleshoot those DTCs first.




A

2.CHECK ENGINE COOLING SYSTEM

B

2.CHECK ENGINE COOLING SYSTEM
a.

Check for defects in the engine cooling system that might cause the system to be too cold, such as abnormal cooling fan operation or any modifications.


Result:
Proceed to
OK
NG



OK

3.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

NG

REPAIR OR REPLACE ENGINE COOLING SYSTEM

3.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
a.

Inspect the water inlet with thermostat sub-assembly (thermostat opening temperature).

Click hereEngine / Hybrid System>A25A-FKS (COOLING)>THERMOSTAT>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

4.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG