Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › CAMSHAFT OIL CONTROL SOLENOID › 2020.02–2021.02
RM33A0E _51 Engine / Hybrid System _065332 2GR-FKS ENGINE CONTROL _0326376 CAMSHAFT OIL CONTROL SOLENOID A

2GR-FKS ENGINE CONTROL  CAMSHAFT OIL CONTROL SOLENOID  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during camshaft timing oil control solenoid assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
Gas leak from exhaust system is repaired Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 11209 1.REMOVE V-BANK COVER SUB-ASSEMBLY

Hide 15370 2.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)

a.
A408188

Disconnect the camshaft timing oil control solenoid assembly connector.


b.

Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

NOTICE:

If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.



c.

Remove the O-ring from the camshaft timing oil control solenoid assembly.

NOTICE:
·

If the O-ring comes off in the timing chain cover assembly, make sure to remove it.

·

Do not drop the O-ring into the timing chain cover assembly.




Hide 15370 3.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)

a.
A408190

Disconnect the camshaft timing oil control solenoid assembly connector.


b.

Disengage the clamp to disconnect the engine wire.


c.

Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

NOTICE:

If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.



d.

Remove the O-ring from the camshaft timing oil control solenoid assembly.

NOTICE:
·

If the O-ring comes off in the timing chain cover assembly, make sure to remove it.

·

Do not drop the O-ring into the timing chain cover assembly.




Hide 53736 4.REMOVE FRONT FENDER APRON SEAL RH

Hide 15370 5.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)

a.
A408191

Disconnect the camshaft timing oil control solenoid assembly connector.


b.

Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

NOTICE:

If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.



c.

Remove the O-ring from the camshaft timing oil control solenoid assembly.

NOTICE:
·

If the O-ring comes off in the timing chain cover assembly, make sure to remove it.

·

Do not drop the O-ring into the timing chain cover assembly.




Hide 6.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 15370 7.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

a.
A408189

Disconnect the camshaft timing oil control solenoid assembly connector.


b.

Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

NOTICE:

If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.



c.

Remove the O-ring from the camshaft timing oil control solenoid assembly.

NOTICE:
·

If the O-ring comes off in the timing chain cover assembly, make sure to remove it.

·

Do not drop the O-ring into the timing chain cover assembly.