Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › CYLINDER HEAD › 2020.02–2021.02
RM33A0E _51 Engine / Hybrid System _065333 2GR-FKS ENGINE MECHANICAL _0327372 CYLINDER HEAD A

2GR-FKS ENGINE MECHANICAL  CYLINDER HEAD  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of fuel injector assembly (for port injection)

·

Replacement of fuel injector assembly (for direct injection)

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leak from exhaust system is repaired

·

Replacement of knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

PROCEDURE

Hide 13711 1.REMOVE INTAKE VALVE

a.
A366177C01
1.344,0.281 1.833,0.281 1.833,0.281 1.552,1.104 true 2.115,1.844 2.469,1.844 false 0.177,1.323 0.323,1.229 false 1.885,0.208 2.344,0.406 0.458,0.198 10 false SST 2.521,1.76 2.833,1.917 0.313,0.156 10 false *a 0.021,1.271 0.333,1.427 0.313,0.156 10 false *a
*a Wooden Block


Using SST and wooden blocks, compress the inner compression spring and remove the 6 valve spring retainer locks from the valve spring retainer.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 6 valve spring retainers, 6 inner compression springs and 6 intake valves from the cylinder head LH.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13715 2.REMOVE EXHAUST VALVE

a.
A366178C01
2.104,1.177 1.625,0.313 1.625,0.313 2.188,0.438 true 2.552,2.021 2.844,2.021 false 1.323,0.229 1.781,0.427 0.458,0.198 10 false SST 2.917,1.927 3.229,2.083 0.313,0.156 10 false *a
*a Wooden Block


Using SST and wooden blocks, compress the inner compression spring and remove the 6 valve spring retainer locks from the valve spring retainer.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 6 valve spring retainers, 6 inner compression springs and 6 exhaust valves from the cylinder head LH.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13711E 3.REMOVE INTAKE VALVE STEM OIL SEAL

a.
A366179

Using needle-nose pliers, remove the 6 intake valve stem oil seals from the intake valve guide bush.


Hide 13715A 4.REMOVE EXHAUST VALVE STEM OIL SEAL

HINT:

Use the same procedure as for the intake side.


Hide 13734 5.REMOVE VALVE SPRING SEAT

a.
A366180

Using compressed air and a Magnet Hand, remove the 12 valve spring seats by blowing air onto them from the cylinder head LH.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 11117E 6.REMOVE NO. 1 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a No. 1 straight screw plug or a plug is corroded, replace it.


a.
A366181

Using a 10 mm hexagon socket wrench, remove the 2 No. 1 straight screw plugs and 2 water hole gaskets from the cylinder head LH.


Hide 11117F 7.REMOVE NO. 2 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a No. 2 straight screw plug or a plug is corroded, replace it.


a.
A366182

Using a 14 mm hexagon wrench, remove the No. 2 straight screw plug and cylinder head screw plug gasket from the cylinder head LH.


Hide 11117G 8.REMOVE NO. 3 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a No. 3 straight screw plug or a plug is corroded, replace it.


a.
A366165

Using a 10 mm hexagon socket wrench, remove the 4 No. 3 straight screw plugs and 4 cylinder head screw plug gaskets from the cylinder head LH.