Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › CYLINDER BLOCK › 2020.02–2021.02
RM33A0E _51 Engine / Hybrid System _065333 2GR-FKS ENGINE MECHANICAL _0327373 CYLINDER BLOCK A

2GR-FKS ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of piston or piston ring

·

Replacement of fuel injector assembly (for port injection)

·

Replacement of fuel injector assembly (for direct injection)

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leak from exhaust system is repaired

·

Replacement of knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

PROCEDURE

Hide 11445 1.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A370639

Remove the cylinder block water jacket spacer and cylinder block water jacket spacer LH from the cylinder block sub-assembly.


Hide 2.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Check that the matchmarks on the connecting rod sub-assembly and connecting rod cap are aligned.

HINT:

The matchmarks on the connecting rod sub-assembly and connecting rod cap are guides for correct reassembly.



b.
A366224C01
0,0 0,0 false
V100136

Front of Engine


Remove the 2 connecting rod bolts.


c.
A366225

Using the 2 removed connecting rod bolts, remove the connecting rod cap and lower connecting rod bearing by wiggling the connecting rod cap right and left.

HINT:

Keep the lower connecting rod bearing installed to the connecting rod cap.



d.
A366226C01
0.49,0.563 1.885,0.958 true 0.302,0.458 0.615,0.615 0.313,0.156 10 false *a
*a Ridge Reamer


Using a ridge reamer, remove all of the carbon from the top of the cylinder.


e.

Push the piston, connecting rod sub-assembly and upper connecting rod bearing through the top of the cylinder block sub-assembly.

HINT:
·

Keep the connecting rod bearing, connecting rod sub-assembly and connecting rod cap together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 13041 3.REMOVE CONNECTING ROD BEARING

a.

Remove the connecting rod bearings from the connecting rod sub-assembly and connecting rod cap.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13011 4.REMOVE PISTON RING SET

a.
A366227C01
0.719,0.521 1.479,0.521 false 0.531,0.448 0.844,0.604 0.313,0.156 10 false *a
*a Piston Ring Expander


Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.


b.

Remove the oil ring expander and 2 side rails by hand.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 5.REMOVE PISTON

a.
A366228

Check the fitting condition between the piston and piston pin.

i.

Try to move the piston back and forth on the piston pin.

HINT:

If abnormal movement is felt, replace the piston and piston pin as a set.




b.
A366229

Remove the connecting rod sub-assembly from the piston.

i.

Using a screwdriver, pry out the piston pin hole snap ring (front side).

NOTICE:
·

Do not remove the piston pin hole snap ring (rear side) unless it has to be replaced.

·

Be careful not to damage the piston when removing the piston pin hole snap ring (rear side).




ii.
A366230

Gradually heat the piston to approximately 80°C (176°F).

CAUTION:

Be sure to wear protective gloves.



iii.
A366231

Using a brass bar and a hammer, lightly tap out the piston pin and remove the connecting rod sub-assembly.

HINT:
·

The piston and piston pin are a matched set.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.





c.
A366232

Using a gasket scraper, remove any carbon from the piston top.

NOTICE:

Be careful not to scratch the piston.



d.
A366233

Using a groove cleaning tool or a broken ring, clean the piston ring grooves.


e.
A366234

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 13411 6.REMOVE CRANKSHAFT

a.
A366235N01
2.083,1.802 2.24,2 0.156,0.198 10 true 1 2.51,1.375 2.667,1.573 0.156,0.198 10 true 4 2.854,1.042 3.01,1.24 0.156,0.198 10 true 3 3.271,0.833 3.427,1.031 0.156,0.198 10 true 2 1.313,0.177 1.469,0.375 0.156,0.198 10 true 5 1.031,0.448 1.188,0.646 0.156,0.198 10 true 8 0.656,0.719 0.813,0.917 0.156,0.198 10 true 7 0.365,1.615 0.521,1.813 0.156,0.198 10 true 6

Uniformly loosen and remove the 8 crankshaft bearing cap set bolts and 8 seal washers in several steps in the order shown in the illustration.


b.
A366236N01
0.271,1.583 0.427,1.781 0.156,0.198 10 true 1 0.927,1.604 1.083,1.802 0.156,0.198 10 true 5 2.385,1.604 2.542,1.802 0.156,0.198 10 true 7 3.063,1.594 3.219,1.792 0.156,0.198 10 true 3 3.052,1.219 3.281,1.458 0.229,0.24 10 true 11 3.083,0.958 3.302,1.188 0.219,0.229 10 true 12 3.031,0.604 3.188,0.802 0.156,0.198 10 true 4 2.385,0.573 2.542,0.771 0.156,0.198 10 true 8 2.385,0.917 2.615,1.156 0.229,0.24 10 true 16 2.385,1.208 2.615,1.458 0.229,0.25 10 true 15 0.938,0.583 1.094,0.781 0.156,0.198 10 true 6 0.844,0.896 1.083,1.156 0.24,0.26 10 true 14 0.865,1.188 1.104,1.427 0.24,0.24 10 true 13 0.281,0.594 0.438,0.792 0.156,0.198 10 true 2 0.208,0.927 0.427,1.177 0.219,0.25 10 true 10 0.281,1.208 0.438,1.406 0.156,0.198 10 true 9

Uniformly loosen the 16 crankshaft bearing cap set bolts in several steps in the order shown in the illustration.


c.
A366237C01
1.667,1.417 2.531,2.385 true 1.521,2.979 1.75,2.667 true 0.74,2.927 0.969,2.615 true 1.354,4.063 0.74,4.271 0.74,4.271 1.135,3.875 true 0.99,2.448 1.302,2.604 0.313,0.156 10 false *1 1.781,2.479 2.094,2.635 0.313,0.156 10 false *2 2.583,2.375 2.896,2.531 0.313,0.156 10 false *a 0.563,4.229 0.875,4.385 0.313,0.156 10 false *b
*1 Cylinder Block Sub-assembly
*2 Crankshaft Bearing Cap
*a Protective Tape
*b Contact Surface


Using a screwdriver with its tip wrapped with protective tape, pry out the crankshaft bearing caps. Remove the 4 crankshaft bearing caps and 4 lower crankshaft bearings as a set.

NOTICE:
·

Push up the crankshaft bearing cap slowly and evenly, alternating between the right and left side so that the crankshaft bearing cap can be removed.

·

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and the crankshaft bearing cap.




d.

Remove the crankshaft.


Hide 11711 7.REMOVE CRANKSHAFT BEARING

a.

Remove the upper crankshaft bearings and lower crankshaft bearings.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 11011 8.REMOVE CRANKSHAFT THRUST WASHER SET

a.
A366482

Remove the crankshaft thrust washer set from the cylinder block sub-assembly.


Hide 15708 9.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A366483

Using a 5 mm hexagon socket wrench, remove the 3 bolts and 3 No. 1 oil nozzle sub-assemblies.


b.

Check the 3 No. 1 oil nozzle sub-assemblies for damage or clogging.

HINT:

If there is damage or clogs, replace the No. 1 oil nozzle sub-assembly.