Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM33A0E _51 Engine / Hybrid System _065332 2GR-FKS ENGINE CONTROL _0329835 SFI SYSTEM J

2GR-FKS ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump (for low pressure side) circuit consists of the ECM, fuel pump (for low pressure side) and fuel pump control ECU (which operates the fuel pump (for low pressure side)). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU. Based on the signal sent from the ECM, the fuel pump control ECU adjusts the fuel pump (for low pressure side) operation speed.

WIRING DIAGRAM

A410587E09
0.385,6.281 2.073,6.479 1.688,0.198 10 false *: Shielded 0.583,5.281 2.271,5.479 1.688,0.198 10 false Battery 0.417,4.177 2.104,4.375 1.688,0.198 10 false FL MAIN 1.708,2.906 3.396,3.104 1.688,0.198 10 false EFI-MAIN NO. 2 2,1.76 3.688,1.958 1.688,0.198 10 false EFI-MAIN NO. 1 0.74,1.583 2.427,1.781 1.688,0.198 10 false EFI-MAIN NO. 1 4.458,3.073 6.146,3.271 1.688,0.198 10 false EFI-MAIN NO. 2 3.635,6 5.323,6.198 1.688,0.198 10 false Fuel Pump Control ECU 6.083,4.583 6.49,4.802 0.406,0.219 10 false FPC 6.417,6.021 6.823,6.24 0.406,0.219 10 false ECM 2.156,3.917 3.844,4.115 1.688,0.198 10 false BLPU 2.156,4.448 3.844,4.646 1.688,0.198 10 false BLPV 2.135,4.979 3.823,5.177 1.688,0.198 10 false BLPW 2.156,5.531 3.844,5.729 1.688,0.198 10 false BLPE 1.5,6.146 2.698,6.563 1.198,0.417 10 false Fuel Pump (for Low Pressure Side) 1.5,5.99 3.188,6.188 1.688,0.198 10 false R43 2.823,0.802 4.51,1 1.688,0.198 10 false 2 2.042,1.302 3.729,1.5 1.688,0.198 10 false 3 2.052,0.813 3.74,1.01 1.688,0.198 10 false 1 2.813,1.313 4.5,1.51 1.688,0.198 10 false 5 4.542,2.156 6.229,2.354 1.688,0.198 10 false 2 5.344,2.167 7.031,2.365 1.688,0.198 10 false 1 5.333,2.667 7.021,2.865 1.688,0.198 10 false 5 4.552,2.625 6.24,2.823 1.688,0.198 10 false 3 6.052,0.823 6.781,1.219 0.729,0.396 10 false MREL 5.781,0.813 6.51,1.208 0.729,0.396 10 false 46 5.802,4.563 6.208,4.781 0.406,0.219 10 false 18 2.625,3.792 3.031,4.01 0.406,0.219 10 false 3 2.625,4.854 3.031,5.073 0.406,0.219 10 false 2 2.625,4.323 3.031,4.542 0.406,0.219 10 false 4 2.625,5.385 3.031,5.604 0.406,0.219 10 false 1 3.646,3.896 4.052,4.115 0.406,0.219 10 false R17 3.729,4.26 4.135,4.479 0.406,0.219 10 false 3 3.719,4.781 4.125,5 0.406,0.219 10 false 4 3.719,5.323 4.125,5.542 0.406,0.219 10 false 1 4.896,3.938 5.302,4.156 0.406,0.219 10 false 1 4.896,4.49 5.302,4.708 0.406,0.219 10 false 2 4.896,5.063 5.302,5.281 0.406,0.219 10 false 3 3.74,3.698 4.146,3.917 0.406,0.219 10 false 2 3.646,4.438 4.052,4.656 0.406,0.219 10 false R17 3.635,4.969 4.042,5.188 0.406,0.219 10 false R17 3.646,5.5 4.052,5.719 0.406,0.219 10 false R17 3.99,3.917 5.677,4.115 1.688,0.198 10 false FPU 4.521,4.135 6.208,4.333 1.688,0.198 10 false +B 4,4.448 5.688,4.646 1.688,0.198 10 false FPV 4.01,4.979 5.698,5.177 1.688,0.198 10 false FPW 4,5.521 5.688,5.719 1.688,0.198 10 false FPG 4.427,4.688 4.833,4.906 0.406,0.219 10 false FPC 4.417,5.271 4.823,5.49 0.406,0.219 10 false GND 4.802,4.115 5.208,4.333 0.406,0.219 10 false R18 4.813,4.667 5.219,4.885 0.406,0.219 10 false R18 4.802,5.25 5.208,5.469 0.406,0.219 10 false R18 3.24,5.667 3.646,5.885 0.406,0.219 10 false * 6.083,6.021 6.49,6.24 0.406,0.219 10 false A23

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FUEL LEAK
a.

Check around and beneath the vehicle for fuel leaks, fumes, etc.

OK:

No fuel leaks present.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY)

NG

REPAIR OR REPLACE FUEL LEAK POINT

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 40
Standard:
GTS Operation Standard
ON Operating sounds can be heard from fuel pump (for low pressure side)



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO)

NG

7.PERFORM ACTIVE TEST USING GTS (FUEL PUMP SINGLE PHASE ENERGIZATION)
3.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO)
a.

Install the fuel pressure gauge (for low pressure line of low pressure side).

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio / Data List / Fuel Pressure (Low) / Fuel Pressure 2.

Powertrain > Engine > Active Test
Active Test Display
Control the Fuel Pump Duty Ratio
Data List Display
Fuel Pressure (Low) / Fuel Pressure 2
50004 372 39 267
Standard:
Techstream Operation Standard
Low Data List value and fuel pressure gauge are within +/-50 kPag of each other
High


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for low pressure side).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (FUEL PRESSURE)

NG

REPLACE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY (FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))

4.READ VALUE USING GTS (FUEL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Target Fuel Pressure (Low) / Target Fuel Pressure 2, Fuel Pressure (Low) / Fuel Pressure 2 and Low Fuel Pressure Sensor.

Powertrain > Engine > Data List
Tester Display
Target Fuel Pressure (Low) / Target Fuel Pressure 2
Fuel Pressure (Low) / Fuel Pressure 2
Low Fuel Pressure Sensor
50003 372 266,267,545
Result:
Result Proceed to
Low Fuel Pressure Sensor value is within +/- 65 kPag of the Target Fuel Pressure (Low) / Target Fuel Pressure 2 A
Low Fuel Pressure Sensor value is more than 65 kPag higher than the Target Fuel Pressure (Low) / Target Fuel Pressure 2 B
Low Fuel Pressure Sensor value is more than 65 kPag lower than the Target Fuel Pressure (Low) / Target Fuel Pressure 2 C




A

5.CHECK FUEL PRESSURE

B

REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL PUMP>REMOVAL

HINT:

Relief blockage such as clogging of the jet pump is suspected.



C

6.CHECK SHORTAGE OF FUEL
5.CHECK FUEL PRESSURE
a.

Install the fuel pressure gauge (for low pressure line of low pressure side).

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


b.

Start the engine.


c.

Measure the fuel pressure at idle.

Standard Fuel Pressure:

196 to 833 kPa (2.0 to 8.5 kgf/cm2, 28 to 121 psi)


HINT:

Refer to Standard Idle Speed.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION



d.

Stop the engine.


e.

Check that the fuel pressure remains as specified for 5 minutes.

Standard Fuel Pressure:

98 kPa (1.0 kgf/cm2, 14.2 psi) or more


HINT:

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE

HINT:

If the difference between Target Fuel Pressure (Low) / Target Fuel Pressure 2 and Low Fuel Pressure Sensor is more than 200 kPa in the freeze frame data of DTC (P008700, P01902A, P107A2A) and the malfunctioning part could not be identified, replace the fuel pump (for low pressure side) as the fuel supply system, which cannot reproduce symptoms easily, may be malfunctioning.



NG

REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

6.CHECK SHORTAGE OF FUEL
a.

Check the amount of fuel remaining.


HINT:
·

No fuel remains in the fuel tank: Malfunction of the fuel sender gauge assembly is suspected.

·

Only the fuel pump side fuel chamber has no fuel remaining: Malfunction of the jet pump is suspected.

·

Fuel remains in the fuel tank: Malfunction of the fuel pump (for low pressure side) is suspected.

·

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

7.PERFORM ACTIVE TEST USING GTS (FUEL PUMP SINGLE PHASE ENERGIZATION)
A461564C02
0.396,2.396 0.823,2.688 0.427,0.292 0.479,2.458 0.938,2.656 0.458,0.198 10 false R43 0.167,0.135 0.625,0.333 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Fuel Pump (for low pressure side))


a.

Disconnect the fuel pump (for low pressure side) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Fuel Pump Single Phase Energization.

Powertrain > Engine > Active Test
Tester Display
Fuel Pump Single Phase Energization
50004 372 49

f.

Operate the fuel pump control ECU using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
R43-3 (BLPU) - Body ground U Phase 4.4 to 8.4 V*
R43-4 (BLPV) - Body ground V Phase 4.4 to 8.4 V*
R43-2 (BLPW) - Body ground W Phase 4.4 to 8.4 V*


HINT:
·

*: This Active Test restricts the fuel pump control ECU output duty cycle to 50%. Therefore, the output voltage of the fuel pump control ECU will be approximately 50% of the power source voltage.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).

·

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

NG

8.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP (FOR LOW PRESSURE SIDE))
8.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP (FOR LOW PRESSURE SIDE))
a.

Disconnect the fuel pump control ECU connector.


b.

Disconnect the fuel pump (for low pressure side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R17-2 (FPU) - R43-3 (BLPU) Always Below 1 Ω
R17-3 (FPV) - R43-4 (BLPV) Always Below 1 Ω
R17-4 (FPW) - R43-2 (BLPW) Always Below 1 Ω
R17-2 (FPU) or R43-3 (BLPU) - Body ground and other terminals Always 10 kΩ or higher
R17-3 (FPV) or R43-4 (BLPV) - Body ground and other terminals Always 10 kΩ or higher
R17-4 (FPW) or R43-2 (BLPW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FUEL PUMP CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FUEL PUMP CONTROL ECU)
A428848C46
0.5,1.083 0.917,1.333 0.417,0.25 1.083,1.708 1.417,1.333 false 2.26,1.729 1.969,1.344 false 0.125,0.125 0.438,0.281 0.313,0.156 10 false *a 0.583,1.104 1.031,1.323 0.448,0.219 10 false R18 0.979,1.729 1.427,1.948 0.448,0.219 10 false +B 2.177,1.771 2.625,1.99 0.448,0.219 10 false GND
*a Front view of wire harness connector
(to Fuel Pump Control ECU)


a.

Disconnect the fuel pump control ECU connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R18-1 (+B) - R18-3 (GND) Engine switch on (IG) 11 to 14 V


HINT:

Make a note of the measured voltage as it may be used in a following Active Test.



Result:
Proceed to
OK
NG



OK

10.INSPECT ECM (FPC TERMINAL)

NG

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - BODY GROUND)
10.INSPECT ECM (FPC TERMINAL)
A428848C47
0.5,1.083 0.917,1.333 0.417,0.25 1.74,1.823 1.729,1.396 true 0.229,0.323 0.542,0.521 0.313,0.198 10 false *a 0.573,1.104 0.885,1.302 0.313,0.198 10 false R18 1.604,1.844 1.917,2.042 0.313,0.198 10 false FPC
*a Front view of wire harness connector
(to Fuel Pump Control ECU)


a.

Disconnect the fuel pump control ECU connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Fuel Pump Single Phase Energization.

Powertrain > Engine > Active Test
Tester Display
Fuel Pump Single Phase Energization
50004 372 49

f.

Operate the fuel pump control ECU using the Active Test function and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Techstream Operation Specified Condition
R18-2 (FPC) - Body ground Before Active Test → During Active Test Before Active Test: Resistance is stable → During Active Test: Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the FPC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP CONTROL ECU

NG

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)
11.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)
a.

Disconnect the fuel pump control ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R18-2 (FPC) - A23-18 (FPC) Always Below 1 Ω
R18-2 (FPC) or A23-18 (FPC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - BODY GROUND)
a.

Disconnect the fuel pump control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R18-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF EFI-MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF EFI-MAIN NO. 2 RELAY)
a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 2 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.INSPECT EFI-MAIN NO. 2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 2 RELAY)

14.INSPECT EFI-MAIN NO. 2 RELAY

Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

NG

REPLACE EFI-MAIN NO. 2 RELAY

15.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 1 relay) - A23-46 (MREL) Always Below 1 Ω
2 (EFI-MAIN NO. 1 relay) or A23-46 (MREL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - EFI-MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - EFI-MAIN NO. 2 RELAY)
a.

Remove the EFI-MAIN NO. 1 and EFI-MAIN NO. 2 relays from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 1 relay) - 2 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) or 2 (EFI-MAIN NO. 2 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU)
a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the fuel pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 2 relay) - R18-1 (+B) Always Below 1 Ω
5 (EFI-MAIN NO. 2 relay) or R18-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR