To prevent injury due to contact with an operating V-ribbed belt or cooling fan, keep your hands and clothing away from the V-ribbed belt and cooling fans when working in the engine compartment with the engine running or the engine switch on (IG).
1.INSPECT ENGINE COOLANT
2.INSPECT ENGINE OIL
3.CHECK BATTERY CONDITION
19100P
4.INSPECT SPARK PLUG
17801
5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly.
Visually check that the air cleaner filter element sub-assembly is not damaged or excessively oily.
If there is any dirt or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.
If any dirt or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.
Install the air cleaner filter element sub-assembly.
16361A
6.INSPECT V-RIBBED BELT
16620
7.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
Remove the V-ribbed belt.
Turn the V-ribbed belt tensioner assembly clockwise and counterclockwise and check that it turns smoothly and does not catch.
If the V-ribbed belt tensioner assembly does not turn smoothly or catches, replace the V-ribbed belt tensioner assembly.
Install the V-ribbed belt.
Click hereGeneral>MAINTENANCE>2GR-FKS DRIVE BELT>INSTALLATION
13750
8.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE
Rev up the engine several times. Check that the engine does not emit unusual noises.
If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.
If any defects or problems are found during the inspection, perform valve lash adjuster assembly inspection.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION
9.INSPECT IGNITION TIMING
Check the ignition timing with the cooling fans off.
Turn off all the electrical systems and the A/C.
When checking the ignition timing, the transaxle should be in neutral or park.
Warm up and stop the engine.
When using the GTS:
Connect the GTS to the DLC3.
Start the engine and run it at idle.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Ignition Timing Cylinder #1
| Tester Display |
|---|
| Ignition Timing Cylinder #1 |
12 to 24° BTDC at idle
Check that the ignition timing advances immediately when the engine speed is increased.
Enter the following menus: Powertrain / Engine / Active Test / Activate the TC Terminal / ON.
| Active Test Display |
|---|
| Activate the TC Terminal |
| Data List Display |
|---|
| Ignition Timing Cylinder #1 |
Monitor Ignition Timing Cylinder #1 of the Data List.
8 to 12° BTDC at idle
When not using the GTS:
| *a | DLC3 |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Confirm the terminal numbers before connecting them. Connecting the wrong terminals may damage electrical components.
Remove the front wheel RH.
Remove the front fender apron seal RH.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
Connect the clip of a timing light to the ignition coil wire for the No. 1 cylinder.
Use a timing light that detects primary signals.
Start the engine and run it at idle.
| *a | Cutout |
| *b | 10° BTDC |
| *c | TDC |
Check the ignition timing at idle.
8 to 12° BTDC at idle
If the cutout of the crankshaft pulley is approximately aligned the protrusion (10° BTDC) of the timing chain cover assembly, the ignition timing meets the standard.
Run the engine at 1000 to 1300 rpm for 5 seconds, and then check that the engine speed returns to engine idle speed.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Check the ignition timing at idle.
12 to 24° BTDC at idle
Confirm that the ignition timing advances immediately when the engine speed is increased.
Disconnect the clip of the timing light from the ignition coil wire for the No. 1 cylinder.
Install the front fender apron seal RH.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
Install the front wheel RH.
10.INSPECT ENGINE IDLE SPEED
Check the idle speed with the cooling fans off.
Turn off all the electrical systems and the A/C.
When checking the idle speed, the transaxle should be in neutral or park.
Warm up and stop the engine.
Connect the GTS to the DLC3.
Start the engine and run it at idle.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Read the value displayed on the GTS.
600 to 700 rpm
11.INSPECT COMPRESSION
Keep the spark plug holes free of foreign matter when measuring the compression pressure.
Warm up and stop the engine.
Check for DTCs.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
Remove the 6 spark plugs.
Check the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Start.
| Tester Display |
|---|
| Check the Cylinder Compression |
Depress and hold the brake pedal, and push the engine switch. Then check the compression pressure.
1400 kPa (14.3 kgf/cm2, 203 psi)
1050 kPa (10.7 kgf/cm2, 152 psi)
200 kPa (2.0 kgf/cm2, 29 psi) or less
Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
Inspect all cylinders in the same way.
Measure the compression pressure as quickly as possible.
If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole then inspect the cylinder compression pressure again.
If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.
If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.
Install the 6 spark plugs.
Click hereGeneral>MAINTENANCE>2GR-FKS SPARK PLUG>INSTALLATION
Clear the DTCs.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.
12.INSPECT CO/HC
This check determines whether or not the idle CO/HC complies with regulations.
Start the engine.
Run the engine speed at 2500 rpm for approximately 180 seconds.
Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.
Immediately check the CO/HC concentration at idle and then at an engine speed of 2500 rpm.
When performing a 2 mode test (with the engine idling/running at 2500 rpm), the measurement procedures are determined by applicable local regulations.
If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.
Check for DTCs.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
See the following table for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problem | Cause |
|---|---|---|---|
| Normal | High | Rough idle | 1.
Faulty ignition: -
Incorrect valve timing -
Fouled, shorted or improperly gapped spark plugs 2.
Incorrect valve clearance (valve lash adjuster assembly) 3.
Leaks in intake or exhaust valves 4.
Leaks in cylinders |
| Low | High | Rough idle
(Fluctuating HC reading) |
1.
Vacuum leaks: -
PCV hoses -
Intake manifold -
Throttle body with motor assembly -
Brake booster line 2.
Lean mixture causing misfire |
| High | High | Rough idle
(Black smoke from exhaust) |
1.
Restricted air cleaner filter element sub-assembly 2.
Plugged PCV valve 3.
Faulty SFI system: -
Fuel pressure regulator assembly -
Engine coolant temperature sensor -
Mass air flow meter sub-assembly -
ECM -
Fuel injector assemblies -
Throttle position sensor (built into throttle body with motor assembly) |