Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2021.02
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 2 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Central gateway ECU (network gateway ECU)

·

ECM

·

TCM

·

No. 2 CAN junction connector

·

No. 4 CAN junction connector



WIRING DIAGRAM

C451578E01
0.448,1.021 0.906,1.219 0.458,0.198 10 false 120 Ω 0.99,1.177 1.448,1.375 0.458,0.198 10 false CA4L 0.969,0.656 1.427,0.854 0.458,0.198 10 false CA4H 1.458,0.635 1.917,0.833 0.458,0.198 10 false 18 1.479,1.177 1.938,1.375 0.458,0.198 10 false 17 0.104,1.719 0.563,1.917 0.458,0.198 10 false K76 0.469,1.729 2.448,2.167 1.979,0.438 10 false Central Gateway ECU (Network Gateway ECU) 2.854,1.281 3.313,1.479 0.458,0.198 10 false K127 2.865,0.76 3.323,0.958 0.458,0.198 10 false K127 3.146,1.719 4.427,2.417 1.281,0.698 10 false No. 4 CAN Junction Connector 4.042,1.281 4.5,1.479 0.458,0.198 10 false K128 4.115,1.073 4.573,1.271 0.458,0.198 10 false 22 4.042,0.76 4.5,0.958 0.458,0.198 10 false K128 4.104,0.552 4.563,0.75 0.458,0.198 10 false 11 2.948,0.552 3.406,0.75 0.458,0.198 10 false 1 2.917,1.073 3.375,1.271 0.458,0.198 10 false 12 4.042,4.031 4.5,4.229 0.458,0.198 10 false 9 4.052,4.542 4.51,4.74 0.458,0.198 10 false 20 3,4.542 3.458,4.74 0.458,0.198 10 false 22 2.99,4.01 3.448,4.208 0.458,0.198 10 false 11 0.969,4.021 1.427,4.219 0.458,0.198 10 false CANH 0.979,4.573 1.438,4.771 0.458,0.198 10 false CANL 0.479,4.365 0.938,4.563 0.458,0.198 10 false 120 Ω 1.521,4.021 1.979,4.219 0.458,0.198 10 false 8*2*3 1.479,4.552 1.938,4.75 0.458,0.198 10 false 18*2*3 5.417,0.833 7.156,1.167 1.74,0.333 10 false *2: for A25A-FKS 4,2.771 4.458,2.969 0.458,0.198 10 false 10 4.021,3.281 4.479,3.479 0.458,0.198 10 false 21 5.417,1.167 7.156,1.5 1.74,0.333 10 false *3: for M20A-FKS 5.417,1.5 7.156,1.833 1.74,0.333 10 false *4: for CVT (K120) 6.01,4.135 6.469,4.333 0.458,0.198 10 false CANH 6.021,4.656 6.479,4.854 0.458,0.198 10 false CANL 5.74,4.031 6.208,4.323 0.469,0.292 10 false 15 5.75,4.552 6.219,4.844 0.469,0.292 10 false 16 5.417,0.5 7.156,0.865 1.74,0.365 10 false *1: for 2GR-FKS 3.146,5.125 4.427,5.823 1.281,0.698 10 false No. 2 CAN Junction Connector 5.823,5.135 6.281,5.333 0.458,0.198 10 false C111 2.792,5.135 3.25,5.333 0.458,0.198 10 false A67 6.229,5.135 6.823,5.646 0.594,0.51 10 false TCM*4 0.948,5.156 1.542,5.667 0.594,0.51 10 false ECM 0.313,5.156 0.927,5.354 0.615,0.198 10 false A23*1 0.313,5.333 0.958,5.594 0.646,0.26 10 false A24*2*3 1.521,3.802 1.979,4 0.458,0.198 10 false 13*1 1.5,4.354 1.958,4.552 0.458,0.198 10 false 26*1

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A67 No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C451579C01
1.323,1.344 1.813,1.615 0.49,0.271 4.427,1.427 4.427,0.594 4.427,0.594 4.594,0.594 true 4.094,1.708 4.094,2.208 4.094,2.208 3.927,2.208 true 4.427,1.698 4.427,2.198 4.427,2.198 4.594,2.198 true 4.094,1.438 4.094,0.604 4.094,0.604 3.927,0.604 true 4.26,1.417 4.26,0.25 4.26,0.25 4.094,0.25 true 4.26,1.688 4.26,2.521 4.26,2.521 4.094,2.521 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.448,1.396 1.865,1.656 0.417,0.26 10 false A67 3.375,0.5 4.052,0.792 0.677,0.292 10 false CANH*b 3.385,2.125 4.063,2.417 0.677,0.292 10 false CANL*b 4.656,0.51 5.333,0.802 0.677,0.292 10 false CANH*d 4.667,2.125 5.344,2.417 0.677,0.292 10 false CANL*d 3.5,0.167 4.177,0.458 0.677,0.292 10 false CANH*c 3.51,2.448 4.188,2.74 0.677,0.292 10 false CANL*c
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to TCM
(for CVT (K120))
*c to No. 4 CAN Junction Connector *d to ECM


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A67-9 (CANH) - A67-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher TCM*
A67-10 (CANH) - A67-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 4 CAN junction connector
A67-11 (CANH) - A67-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM


*: for CVT (K120)



Result:
Result Proceed to
OK A
NG (Line to ECM) B
NG (Line to No. 4 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)

C

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

D

6.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
2.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A23 or A24 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

C372332C12
1.323,1.344 1.813,1.615 0.49,0.271 4.427,1.427 4.427,0.594 4.427,0.594 4.594,0.594 true 4.427,1.698 4.427,2.198 4.427,2.198 4.594,2.198 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.438,1.396 1.854,1.656 0.417,0.26 10 false A67 4.656,0.51 5.333,0.802 0.677,0.292 10 false CANH*b 4.667,2.125 5.344,2.417 0.677,0.292 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to ECM


Standard Resistance:
Tester Connection Condition Specified Condition
A67-11 (CANH) - A67-22 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result Proceed to
OK (for A25A-FKS or M20A-FKS) A
OK (for 2GR-FKS) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - ECM)

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the K128 No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C381591C35
1.25,1.375 1.729,1.656 0.479,0.281 4.427,1.708 4.427,2.104 4.427,2.104 4.594,2.104 true 4.438,1.417 4.438,0.708 4.438,0.708 4.604,0.708 true 1.333,1.438 1.792,1.635 0.458,0.198 10 false K128 0.135,0.083 0.594,0.281 0.458,0.198 10 false *a 4.698,0.635 5.323,0.958 0.625,0.323 10 false CANH*b 4.688,2.031 5.313,2.354 0.625,0.323 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to No. 2 CAN Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K128-11 (CANH) - K128-22 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher No. 2 CAN junction connector



Result:
Result
OK
NG



OK

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the K127 No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C372332C09
1.323,1.344 1.813,1.615 0.49,0.271 2.76,1.427 2.76,0.583 2.76,0.583 2.573,0.583 true 2.76,1.708 2.76,2.167 2.76,2.167 2.573,2.167 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.417,1.406 1.833,1.667 0.417,0.26 10 false K127 1.99,0.5 2.667,0.792 0.677,0.292 10 false CANH*b 2,2.083 2.677,2.375 0.677,0.292 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K127-1 (CANH) - K127-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

5.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
5.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the K76 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C372332C09
1.323,1.344 1.813,1.615 0.49,0.271 2.76,1.427 2.76,0.583 2.76,0.583 2.573,0.583 true 2.76,1.708 2.76,2.167 2.76,2.167 2.573,2.167 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.417,1.406 1.833,1.667 0.417,0.26 10 false K127 1.99,0.5 2.667,0.792 0.677,0.292 10 false CANH*b 2,2.083 2.677,2.375 0.677,0.292 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
K127-1 (CANH) - K127-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

6.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C451580C01
1.479,0.083 1.885,0.313 0.406,0.229 1.51,0.5 1.677,0.5 1.677,0.5 1.677,1.083 true 1.917,0.5 1.75,0.5 1.75,0.5 1.75,1.083 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.583,0.115 2.021,0.365 0.438,0.25 10 false K76 1.094,0.427 1.531,0.677 0.438,0.25 10 false CA4H 1.99,0.417 2.427,0.667 0.438,0.25 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K76-18 (CA4H) - K76-17 (CA4L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR