Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2021.02
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 3 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area
There is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Radio and display receiver assembly

(w/ Radio and Display Type)

·

Accessory gateway ECU (network gateway ECU)

(w/ Accessory Gateway ECU)

·

Option connector (bus buffer ECU)

(w/ CAN Compatible Optional Devices)

·

Telematics transceiver

(w/ Telematics Transceiver)

·

No. 4 CAN junction connector



WIRING DIAGRAM

C396749E03
0.375,1.073 1.146,1.271 0.771,0.198 10 false 120 Ω 0.917,0.74 1.531,0.938 0.615,0.198 10 false CA3H 0.958,1.219 1.573,1.417 0.615,0.198 10 false CA3L 1.427,0.74 1.583,0.938 0.156,0.198 10 false 6 1.406,1.208 1.719,1.406 0.313,0.198 10 false 21 3.219,0.833 3.833,1.031 0.615,0.198 10 false K127 3.219,1.313 3.833,1.51 0.615,0.198 10 false K127 3.323,0.615 3.479,0.813 0.156,0.198 10 false 9 3.292,1.104 3.604,1.302 0.313,0.198 10 false 20 4.604,0.615 4.76,0.813 0.156,0.198 10 false 1 4.51,0.833 5.125,1.031 0.615,0.198 10 false K128 4.583,1.104 4.896,1.302 0.313,0.198 10 false 12 4.521,1.313 5.135,1.51 0.615,0.198 10 false K128 5.771,0.74 6.083,0.938 0.313,0.198 10 false 13 5.781,1.198 6.094,1.396 0.313,0.198 10 false 14 6.073,0.813 6.688,1.01 0.615,0.198 10 false CANH 6.094,1.302 6.708,1.5 0.615,0.198 10 false CANL 5.198,1.76 5.51,1.958 0.313,0.198 10 false K2 5.417,1.76 7.115,2.604 1.698,0.844 10 false Radio and Display Receiver Assembly*1 4.5,3.073 5.115,3.271 0.615,0.198 10 false K127 4.5,3.542 5.115,3.74 0.615,0.198 10 false K127 3.219,3.073 3.833,3.271 0.615,0.198 10 false K127 3.219,3.552 3.833,3.75 0.615,0.198 10 false K127 4.604,2.854 4.76,3.052 0.156,0.198 10 false 8 4.573,3.344 4.885,3.542 0.313,0.198 10 false 19 3.302,3.333 3.615,3.531 0.313,0.198 10 false 21 3.281,2.865 3.594,3.063 0.313,0.198 10 false 10 2.458,2.969 2.771,3.167 0.313,0.198 10 false 25 2.469,3.448 2.781,3.646 0.313,0.198 10 false 26 1.927,3.042 2.542,3.24 0.615,0.198 10 false CANP 1.948,3.521 2.563,3.719 0.615,0.198 10 false CANN 1.396,3.979 2.01,4.177 0.615,0.198 10 false K156 1.771,3.979 3.521,4.76 1.75,0.781 10 false Telematics Transceiver*4 0.375,5.729 1.146,5.927 0.771,0.198 10 false 120 Ω 5.781,2.958 6.094,3.156 0.313,0.198 10 false 18 5.781,3.438 6.094,3.635 0.313,0.198 10 false 17 6.083,3.052 6.698,3.25 0.615,0.198 10 false CA1H 6.094,3.531 6.708,3.729 0.615,0.198 10 false CA1L 5.083,4.01 5.698,4.208 0.615,0.198 10 false K155 5.458,4 7.094,4.844 1.635,0.844 10 false Accessory Gateway ECU (Network Gateway ECU)*2 0.906,5.375 1.521,5.573 0.615,0.198 10 false CAYH 0.958,5.865 1.573,6.063 0.615,0.198 10 false CAYL 1.427,5.375 1.74,5.573 0.313,0.198 10 false 19 1.438,5.844 1.75,6.042 0.313,0.198 10 false 20 0.031,6.354 0.49,6.552 0.458,0.198 10 false K76 0.323,6.354 2.281,7.198 1.958,0.844 10 false Central Gateway ECU (Network Gateway ECU) 3.208,5.479 3.823,5.677 0.615,0.198 10 false K127 3.219,5.958 3.833,6.156 0.615,0.198 10 false K127 3.281,5.25 3.594,5.448 0.313,0.198 10 false 11 3.292,5.75 3.604,5.948 0.313,0.198 10 false 22 4.5,5.479 5.115,5.677 0.615,0.198 10 false K128 4.51,5.958 5.125,6.156 0.615,0.198 10 false K128 4.615,5.271 4.771,5.469 0.156,0.198 10 false 3 4.583,5.75 4.896,5.948 0.313,0.198 10 false 14 5.844,5.365 6,5.563 0.156,0.198 10 false 2 5.844,5.844 6,6.042 0.156,0.198 10 false 1 6.063,5.469 6.677,5.667 0.615,0.198 10 false CAN+ 6.073,5.938 6.531,6.135 0.458,0.198 10 false CAN- 5.344,6.406 5.958,6.604 0.615,0.198 10 false K143 3.458,6.385 4.688,7.24 1.229,0.854 10 false No. 4 CAN Junction Connector 5.708,6.396 7.125,7.094 1.417,0.698 10 false Option Connector (Bus Buffer ECU)*3 0.104,7.156 4.542,7.354 4.438,0.198 10 false *1: w/ Radio and Display Type 0.115,7.479 4.396,7.677 4.281,0.198 10 false *2: w/ Accessory Gateway ECU 2.719,7.177 6.677,7.521 3.958,0.344 10 false *3: w/ CAN Compatible Optional Devices 2.729,7.49 6.688,7.833 3.958,0.344 10 false *4: w/ Telematics Transceiver

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the telematics transceiver, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the K127 No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C406091C52
0.188,1.229 0.667,1.5 0.479,0.271 3.656,1.229 4.177,1.51 0.521,0.281 6.125,2.229 5.958,2.229 5.958,2.229 5.958,1.729 true 2.719,1.417 2.719,0.417 2.719,0.417 2.885,0.417 true 2.552,1.719 2.552,2.385 2.552,2.385 2.385,2.385 true 2.729,1.719 2.729,2.385 2.729,2.385 2.896,2.385 true 2.552,1.417 2.552,0.417 2.552,0.417 2.385,0.417 true 2.385,1.438 2.385,0.667 2.385,0.667 2.219,0.667 true 2.385,1.698 2.385,2.156 2.385,2.156 2.219,2.156 true 2.875,1.438 2.875,0.667 2.875,0.667 3.042,0.667 true 2.896,1.708 2.896,2.167 2.896,2.167 3.073,2.167 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 3.865,0.104 4.177,0.302 0.313,0.198 10 false *1 6.208,2.146 6.625,2.396 0.417,0.25 10 false BAT 0.271,1.281 0.688,1.49 0.417,0.208 10 false K127 1.802,0.333 2.406,0.573 0.604,0.24 10 false CANH*c 1.823,2.302 2.427,2.542 0.604,0.24 10 false CANL*c 3.115,2.073 3.719,2.313 0.604,0.24 10 false CANL*c 3.094,0.583 3.698,0.823 0.604,0.24 10 false CANH*c 1.635,0.583 2.24,0.823 0.604,0.24 10 false CANH*b 1.667,2.073 2.271,2.313 0.604,0.24 10 false CANL*b 2.938,0.333 3.542,0.573 0.604,0.24 10 false CANH*d 2.938,2.302 3.542,2.542 0.604,0.24 10 false CANL*d 3.74,1.281 4.188,1.531 0.448,0.25 10 false K154
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Accessory Gateway ECU (Network Gateway ECU)
(w/ Accessory Gateway ECU)
*c to Central Gateway ECU (Network Gateway ECU) *d to Telematics Transceiver
(w/ Telematics Transceiver)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K127-8 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Accessory gateway ECU (network gateway ECU)*1
K127-19 (CANL) - K154-16 (BAT)
K127-9 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
K127-20 (CANL) - K154-16 (BAT)
K127-10 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Telematics transceiver*2
K127-21 (CANL) - K154-16 (BAT)
K127-11 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
K127-22 (CANL) - K154-16 (BAT)


·

*1: w/ Accessory Gateway ECU

·

*2: w/ Telematics Transceiver



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)

B

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the K128 No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C406091C53
0.188,1.229 0.667,1.5 0.479,0.271 3.625,1.24 4.115,1.531 0.49,0.292 6.125,2.229 5.958,2.229 5.958,2.229 5.958,1.729 true 1.552,1.438 1.552,0.438 1.552,0.438 1.719,0.438 true 1.552,1.698 1.552,2.365 1.552,2.365 1.719,2.365 true 1.208,1.438 1.208,0.667 1.208,0.667 1.042,0.667 true 1.208,1.698 1.208,2.156 1.208,2.156 1.042,2.156 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 3.865,0.104 4.177,0.302 0.313,0.198 10 false *1 6.208,2.146 6.625,2.396 0.417,0.25 10 false BAT 0.271,1.281 0.688,1.49 0.417,0.208 10 false K128 1.813,2.281 2.417,2.521 0.604,0.24 10 false CANL*c 1.823,0.354 2.427,0.594 0.604,0.24 10 false CANH*c 0.469,0.594 1.073,0.833 0.604,0.24 10 false CANH*b 0.479,2.083 1.083,2.323 0.604,0.24 10 false CANL*b 3.708,1.302 4.25,1.656 0.542,0.354 10 false K154
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Radio and Display Receiver Assembly
(w/ Radio and Display Type)
*c to Option Connector (Bus Buffer ECU)
(w/ CAN Compatible Optional Devices)
- -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K128-1 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Radio and display receiver assembly*1
K128-12 (CANL) - K154-16 (BAT)
K128-3 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Option connector (bus buffer ECU)*2
K128-14 (CANL) - K154-16 (BAT)


·

*1: w/ Radio and Display Type

·

*2: w/ CAN Compatible Optional Devices


HINT:

If there is a short to +B in a CAN bus line without any CAN compatible optional devices connected to the option connector, repair or replace the CAN bus branch line or the option connector.



Result:
Result
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
3.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the K76 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C406091C54
0.271,1.354 0.729,1.594 0.458,0.24 3.583,1.333 4.094,1.594 0.51,0.26 2.885,1.698 2.885,2.198 2.885,2.198 3.052,2.198 true 5.948,1.729 5.948,2.146 5.948,2.146 6.115,2.146 true 2.552,1.698 2.552,2.198 2.552,2.198 2.385,2.198 true 2.885,1.417 2.885,0.667 2.885,0.667 3.052,0.667 true 2.552,1.427 2.552,0.677 2.552,0.677 2.385,0.677 true 0.604,0.302 0.917,0.5 0.313,0.198 10 false *a 3.854,0.333 4.167,0.531 0.313,0.198 10 false *1 0.344,1.385 0.74,1.583 0.396,0.198 10 false K127 6.208,2.052 6.604,2.25 0.396,0.198 10 false BAT 1.823,0.594 2.469,0.844 0.646,0.25 10 false CANH*b 3.125,0.583 3.771,0.833 0.646,0.25 10 false CANH*b 1.854,2.115 2.5,2.365 0.646,0.25 10 false CANL*b 3.115,2.115 3.76,2.365 0.646,0.25 10 false CANL*b 3.698,1.375 4.438,1.771 0.74,0.396 10 false K154
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
K127-9 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
K127-20 (CANL) - K154-16 (BAT)
K127-11 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
K127-22 (CANL) - K154-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C405813C11
1.594,0.198 2.01,0.469 0.417,0.271 4.958,0.385 5.375,0.656 0.417,0.271 1.5,1.229 1.5,0.625 1.5,0.625 1.365,0.625 true 1.385,2.104 1.521,2.104 1.521,2.104 1.521,1.406 true 6.021,2.156 5.854,2.156 5.854,2.156 5.854,1.677 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.688,0.26 2,0.458 0.313,0.198 10 false K76 0.969,0.552 1.521,0.75 0.552,0.198 10 false CA3H 6.135,2.083 6.688,2.281 0.552,0.198 10 false BAT 0.99,2.031 1.542,2.229 0.552,0.198 10 false CA3L 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 5,0.438 5.51,0.719 0.51,0.281 10 false K154
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
K76-6 (CA3H) - K154-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
K76-21 (CA3L) - K154-16 (BAT)


HINT:
·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR