Home › Drivetrain › K120 (CVT) › OIL PAN › from 2021.02
RM33A0E _52 Drivetrain _098634 K120 CVT _0461779 OIL PAN A

K120 CVT  OIL PAN  INSTALLATION  


PROCEDURE

Hide 35015Y 1.INSTALL TRANSAXLE SIDE COVER SUB-ASSEMBLY

a.
C399137C01
0,0 0,0 false
V100145

Area to be Cleaned


Clean the transaxle side cover sub-assembly installation surface of the transaxle case sub-assembly.

NOTICE:

Completely remove any oil or grease from the contact surfaces of the transaxle case sub-assembly.



b.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to a new transaxle side cover sub-assembly.


c.
C413795N01
1.833,3.229 2.052,3.406 0.219,0.177 10 true 11 0.385,3.208 0.531,3.396 0.146,0.188 10 true 1 2.875,3.188 3.021,3.375 0.146,0.188 10 true 4 3,1.135 3.156,1.333 0.156,0.198 10 true 7 3,2.021 3.156,2.208 0.156,0.188 10 true 9 2.896,0.24 3.052,0.438 0.156,0.198 10 true 2 1.906,0 2.052,0.188 0.146,0.188 10 true 5 0.781,0 0.906,0.198 0.125,0.198 10 true 3 0.646,0.677 0.854,0.854 0.208,0.177 10 true 10 0.333,1.104 0.469,1.302 0.135,0.198 10 true 8 0.323,2.094 0.458,2.302 0.135,0.208 10 true 6

Temporarily install the transaxle side cover sub-assembly to the transaxle case sub-assembly with the 11 bolts.


d.

Fully tighten the 11 bolts in the order shown in the illustration.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the transaxle side cover sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 32901L 3.INSTALL OIL COOLER ELBOW SUB-ASSEMBLY

a.

Temporarily install the oil cooler elbow sub-assembly and 2 gaskets to the transaxle housing with the 2 union bolts.


b.
C413796C01
0.781,2.531 0.854,2.354 0.854,2.354 1.021,2.354 false 1.719,2.99 2.031,3.146 0.313,0.156 10 false *a 1.063,2.26 1.375,2.417 0.313,0.156 10 false *b 0.781,0.813 0.938,1.01 0.156,0.198 10 true A 0.531,1.823 0.688,2.021 0.156,0.198 10 false B
*a Torque Wrench Fulcrum Length
*b 17 mm Union Nut Wrench


Fully tighten the union bolt (A).

Torque:
27.5 N*m (280 kgf*cm, 20 ft.*lbf)


c.

Using a 17 mm union nut wrench, fully tighten the union bolt (B).

Torque:
Specified Tightening Torque : 27.5 N*m (280 kgf*cm, 20 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

23.2 N*m (237 kgf*cm, 17 ft.*lbf)




Hide 4.CONNECT OIL COOLER HOSE

a.
C414222C01
1.844,0.385 2.083,0.76 true 2.354,1.479 2.635,1.51 true 1.854,3.021 1.719,3.198 1.719,3.198 2.063,3.021 true 1.635,0.281 1.813,0.448 0.177,0.167 10 true *1 2.667,1.427 2.854,1.594 0.188,0.167 10 true *2 1.552,3.094 1.865,3.25 0.313,0.156 10 false *a 1.74,2.125 2.052,2.281 0.313,0.156 10 false *b 1.719,2.365 2.031,2.521 0.313,0.156 10 false *c
*1 Outlet No. 1 Oil Cooler Hose
*2 Inlet Oil Cooler Hose
*a Paint Mark
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c 0 to 3 mm (0 to 0.118 in.)


Connect the outlet No. 1 oil cooler hose to the oil cooler elbow sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the outlet No. 1 oil cooler hose until it contacts the hose stopper of the oil cooler elbow sub-assembly.

·

Make sure to align the paint mark of the outlet No. 1 oil cooler hose with the paint mark of the oil cooler elbow sub-assembly.

·

Make sure that the clip is within the location shown in the illustration.



HINT:

Perform this procedure only when replacement of the outlet No. 1 oil cooler hose is necessary.



b.

Connect the inlet oil cooler hose to the oil cooler elbow sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the inlet oil cooler hose until it contacts the hose stopper of the oil cooler elbow sub-assembly.

·

Make sure to align the paint mark of the inlet oil cooler hose with the paint mark of the oil cooler elbow sub-assembly.

·

Make sure that the clip is within the location shown in the illustration.



HINT:

Perform this procedure only when replacement of the inlet oil cooler hose is necessary.



c.
C413797C01
1.344,0.708 1.813,1.052 true 1.552,1.698 1.76,1.344 true 2.104,3.021 2.417,3.208 2.417,3.208 2.313,3.021 true 1.135,0.573 1.313,0.74 0.177,0.167 10 true *1 1.427,1.729 1.615,1.896 0.188,0.167 10 true *2 2.448,3.135 2.76,3.292 0.313,0.156 10 false *a 2.281,2.125 2.594,2.281 0.313,0.156 10 false *b 2.313,2.365 2.625,2.521 0.313,0.156 10 false *c
*1 Outlet No. 1 Oil Cooler Hose
*2 Inlet Oil Cooler Hose
*a Paint Mark
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c 0 to 3 mm (0 to 0.118 in.)


Connect the outlet No. 1 oil cooler hose to the transmission oil cooler and slide the clip to secure it.

NOTICE:
·

Make sure to slide the outlet No. 1 oil cooler hose until it contacts the hose stopper of the transmission oil cooler.

·

Make sure to align the paint mark of the outlet No. 1 oil cooler hose with the paint mark of the transmission oil cooler.

·

Make sure that the clip is within the location shown in the illustration.




d.

Connect the inlet oil cooler hose to the transmission oil cooler and slide the clip to secure it.

NOTICE:
·

Make sure to slide the inlet oil cooler hose until it contacts the hose stopper of the transmission oil cooler.

·

Make sure to align the paint mark of the inlet oil cooler hose with the paint mark of the transmission oil cooler.

·

Make sure that the clip is within the location shown in the illustration.




Hide 6.ADJUST CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 7.INSPECT FOR FLUID LEAKS

Hide 53737B 8.INSTALL FRONT FENDER APRON SEAL LH

Hide 51441 9.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 53852K 10.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 11.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH